snakemake_logo

deltazeus/marlin/Configuration.h

@@ -493,10 +493,10 @@
 
 
 
-// deltazeus /w e3dv6 // changed
-#define DEFAULT_Kp 32.65
-#define DEFAULT_Ki 2.89
-#define DEFAULT_Kd 92.27
+// deltazeus /w e3dv6 normalized values // changed
+#define DEFAULT_Kp 33.00
+#define DEFAULT_Ki 3.00
+#define DEFAULT_Kd 95.00
 
 // stoffel-hotend
 //#define DEFAULT_Kp 21.80
@@ -673,7 +673,7 @@
 #define DELTA_DIAGONAL_ROD 202.0        // (mm) changed
 
 // Distance between bed and nozzle Z home position
-#define DELTA_HEIGHT 196.35             // (mm) Get this value from G33 auto calibrate // changed
+#define DELTA_HEIGHT 197.0             // (mm) Get this value from G33 auto calibrate // changed
 
 #define DELTA_ENDSTOP_ADJ { -0.1, -0.20, 0.0 } // Get these values from G33 auto calibrate
 
@@ -989,7 +989,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-#define BLTOUCH
+//#define BLTOUCH
 
 /**
  * Pressure sensor with a BLTouch-like interface
@@ -2324,12 +2324,12 @@
 // @section extras
 
 // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
-//#define FAST_PWM_FAN
+#define FAST_PWM_FAN //changed, needed for sunon fans
 
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
-//#define FAN_SOFT_PWM
+//#define FAN_SOFT_PWM //changed, needed fot sunon fans
 
 // Incrementing this by 1 will double the software PWM frequency,
 // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.

deltazeus/marlin/Configuration_adv.h

@@ -391,7 +391,7 @@
 // When first starting the main fan, run it at full speed for the
 // given number of milliseconds.  This gets the fan spinning reliably
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
-//#define FAN_KICKSTART_TIME 100
+#define FAN_KICKSTART_TIME 500
 
 // Some coolers may require a non-zero "off" state.
 //#define FAN_OFF_PWM  1
@@ -1606,7 +1606,7 @@
 #define LIN_ADVANCE
 #if ENABLED(LIN_ADVANCE)
   //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
-  #define LIN_ADVANCE_K 0    // Unit: mm compression per 1mm/s extruder speed
+  #define LIN_ADVANCE_K 0.38    // Unit: mm compression per 1mm/s extruder speed
   //#define LA_DEBUG            // If enabled, this will generate debug information output over USB.
   #define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
 #endif

openscad/own/2d-to-3d-scad/snakemake.scad

@@ -0,0 +1,29 @@
+// some basic 2d-to-3d-extrusion of Vectorfiles
+// by zeus - zeus@ctdo.de - CC-BY-NC-4.0
+// -> https://www.thingiverse.com/zeus
+// -> https://github.com/zeus86
+// 2021-02-18
+// ###############
+h=4;  //height
+w=25;  //width
+l=112.5; //lenght
+hd=10;  //hole_dia
+emd=1;  // embossing depth
+$fn=100; //resolution
+// ###############
+difference(){ 
+    translate([0,0,h/2*1]){
+        hull(){
+            translate([+(l-w)/2,0,0])cylinder(h=h,r=w/2,center=true,$fn=100);
+            translate([-(l-w)/2,0,0])cylinder(h=h,r=w/2,center=true,$fn=100);
+        }    
+    }
+    translate([w/3,0,h-emd]){
+        scale([0.66,0.66,0.66]){
+            linear_extrude(height = h/2*1){
+                import("snakemake_sw.svg",center=true);
+            }
+        }
+    }
+    translate([-(l/2)+(w/3),0,h/2])cylinder(h=h+0.1,r=hd/2,center=true);
+}