diff --git a/PrusaSlicer/.gitignore b/PrusaSlicer/.gitignore
index f057244..d7ecf96 100644
--- a/PrusaSlicer/.gitignore
+++ b/PrusaSlicer/.gitignore
@@ -1,2 +1,3 @@
 /snapshots/*
 /cache/*
+/vendor/*
diff --git a/PrusaSlicer/filament/PLA_Sunlu_Grasgruen.ini b/PrusaSlicer/filament/PLA_Sunlu_Grasgruen.ini
index 5b33f51..c9412fb 100644
--- a/PrusaSlicer/filament/PLA_Sunlu_Grasgruen.ini
+++ b/PrusaSlicer/filament/PLA_Sunlu_Grasgruen.ini
@@ -1,12 +1,12 @@
-# generated by PrusaSlicer 2.4.1+linux-x64-GTK2 on 2022-05-17 at 21:53:02 UTC
-bed_temperature = 55
+# generated by PrusaSlicer 2.5.0+linux-x64-GTK2 on 2022-09-26 at 18:17:08 UTC
+bed_temperature = 60
 bridge_fan_speed = 100
 compatible_printers = 
 compatible_printers_condition = 
 compatible_prints = 
 compatible_prints_condition = 
 cooling = 1
-disable_fan_first_layers = 1
+disable_fan_first_layers = 2
 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
 extrusion_multiplier = 0.98
 fan_always_on = 1
@@ -45,13 +45,13 @@ filament_unloading_speed = 90
 filament_unloading_speed_start = 100
 filament_vendor = (Unknown)
 filament_wipe = nil
-first_layer_bed_temperature = 55
+first_layer_bed_temperature = 62
 first_layer_temperature = 210
-full_fan_speed_layer = 0
+full_fan_speed_layer = 3
 inherits = 
 max_fan_speed = 100
-min_fan_speed = 40
-min_print_speed = 10
-slowdown_below_layer_time = 8
+min_fan_speed = 50
+min_print_speed = 15
+slowdown_below_layer_time = 15
 start_filament_gcode = "; Filament gcode\n"
 temperature = 205
diff --git a/PrusaSlicer/print/delta.ini b/PrusaSlicer/print/delta.ini
index 11b0449..16f7791 100644
--- a/PrusaSlicer/print/delta.ini
+++ b/PrusaSlicer/print/delta.ini
@@ -1,13 +1,15 @@
-# generated by PrusaSlicer 2.3.0+linux-x64 on 2021-06-14 at 08:38:14 UTC
+# generated by PrusaSlicer 2.5.0+linux-x64-GTK2 on 2022-09-26 at 18:20:40 UTC
 avoid_crossing_perimeters = 0
 avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonic
 bottom_solid_layers = 4
-bottom_solid_min_thickness = 1
+bottom_solid_min_thickness = 0
 bridge_acceleration = 0
 bridge_angle = 0
-bridge_flow_ratio = 0.92
-bridge_speed = 50
+bridge_flow_ratio = 0.95
+bridge_speed = 60
+brim_separation = 0
+brim_type = outer_only
 brim_width = 0
 clip_multipart_objects = 1
 compatible_printers = 
@@ -15,47 +17,60 @@ compatible_printers_condition =
 complete_objects = 0
 default_acceleration = 0
 dont_support_bridges = 1
-draft_shield = 0
+draft_shield = disabled
 elefant_foot_compensation = 0.1
-ensure_vertical_shell_thickness = 1
-external_perimeter_extrusion_width = 0.4
+ensure_vertical_shell_thickness = 0
+external_perimeter_extrusion_width = 0
 external_perimeter_speed = 40
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
 extruder_clearance_radius = 20
-extrusion_width = 0.4
+extrusion_width = 0
 fill_angle = 45
 fill_density = 30%
-fill_pattern = cubic
+fill_pattern = rectilinear
 first_layer_acceleration = 0
-first_layer_extrusion_width = 0.45
-first_layer_height = 0.25
-first_layer_speed = 30
-gap_fill_speed = 30
+first_layer_acceleration_over_raft = 0
+first_layer_extrusion_width = 200%
+first_layer_height = 0.4
+first_layer_speed = 35
+first_layer_speed_over_raft = 30
+fuzzy_skin = none
+fuzzy_skin_point_dist = 0.8
+fuzzy_skin_thickness = 0.3
+gap_fill_enabled = 1
+gap_fill_speed = 40
 gcode_comments = 0
 gcode_label_objects = 0
+gcode_resolution = 0.0125
+gcode_substitutions = 
 infill_acceleration = 0
 infill_anchor = 600%
 infill_anchor_max = 50
 infill_every_layers = 1
 infill_extruder = 1
-infill_extrusion_width = 0.45
+infill_extrusion_width = 0
 infill_first = 0
 infill_only_where_needed = 0
 infill_overlap = 25%
-infill_speed = 100
+infill_speed = 60
 inherits = 
 interface_shells = 0
 ironing = 0
-ironing_flowrate = 13%
+ironing_flowrate = 15%
 ironing_spacing = 0.1
 ironing_speed = 20
-ironing_type = top
-layer_height = 0.25
-max_print_speed = 100
-max_volumetric_speed = 0
+ironing_type = topmost
+layer_height = 0.4
+max_print_speed = 200
+max_volumetric_extrusion_rate_slope_negative = 0
+max_volumetric_extrusion_rate_slope_positive = 0
+max_volumetric_speed = 16
+min_bead_width = 85%
+min_feature_size = 25%
 min_skirt_length = 10
+mmu_segmented_region_max_width = 0
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
@@ -63,57 +78,75 @@ output_filename_format = [input_filename_base].gcode
 overhangs = 1
 perimeter_acceleration = 0
 perimeter_extruder = 1
-perimeter_extrusion_width = 0.4
+perimeter_extrusion_width = 0
+perimeter_generator = arachne
 perimeter_speed = 60
 perimeters = 4
 post_process = 
 print_settings_id = delta
+raft_contact_distance = 0.1
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 3
 raft_layers = 0
 resolution = 0
-seam_position = aligned
+seam_position = rear
 single_extruder_multi_material_priming = 1
-skirt_distance = 4
+skirt_distance = 7
 skirt_height = 1
 skirts = 1
 slice_closing_radius = 0.049
+slicing_mode = regular
 small_perimeter_speed = 50%
 solid_infill_below_area = 70
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
-solid_infill_extrusion_width = 0.45
-solid_infill_speed = 100
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 0
 support_material_angle = 0
 support_material_auto = 1
+support_material_bottom_contact_distance = 0
+support_material_bottom_interface_layers = -1
 support_material_buildplate_only = 0
+support_material_closing_radius = 2
 support_material_contact_distance = 0.25
 support_material_enforce_layers = 0
 support_material_extruder = 1
-support_material_extrusion_width = 0.35
+support_material_extrusion_width = 0
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
 support_material_interface_layers = 3
+support_material_interface_pattern = rectilinear
 support_material_interface_spacing = 0
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear-grid
-support_material_spacing = 2
-support_material_speed = 80
+support_material_spacing = 2.5
+support_material_speed = 70
+support_material_style = grid
 support_material_synchronize_layers = 0
-support_material_threshold = 30
+support_material_threshold = 45
 support_material_with_sheath = 0
-support_material_xy_spacing = 60%
+support_material_xy_spacing = 50%
+thick_bridges = 1
 thin_walls = 1
-threads = 8
+threads = 4
 top_fill_pattern = monotonic
-top_infill_extrusion_width = 0.4
+top_infill_extrusion_width = 0
 top_solid_infill_speed = 40
 top_solid_layers = 4
-top_solid_min_thickness = 1
+top_solid_min_thickness = 0
 travel_speed = 200
+travel_speed_z = 0
+wall_distribution_count = 1
+wall_transition_angle = 10
+wall_transition_filter_deviation = 25%
+wall_transition_length = 100%
 wipe_tower = 0
 wipe_tower_bridging = 10
+wipe_tower_brim_width = 2
 wipe_tower_no_sparse_layers = 0
 wipe_tower_rotation_angle = 0
 wipe_tower_width = 60
diff --git a/PrusaSlicer/printer/delta.ini b/PrusaSlicer/printer/delta.ini
index e1a9817..58b04a9 100644
--- a/PrusaSlicer/printer/delta.ini
+++ b/PrusaSlicer/printer/delta.ini
@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.3.0+linux-x64 on 2021-05-31 at 16:56:56 UTC
+# generated by PrusaSlicer 2.5.0+linux-x64-GTK2 on 2022-09-26 at 18:16:41 UTC
 bed_custom_model = 
 bed_custom_texture = 
 bed_shape = 89.6575x7.84402,88.6327x15.6283,86.9333x23.2937,84.5723x30.7818,81.5677x38.0356,77.9423x45,73.7237x51.6219,68.944x57.8509,63.6396x63.6396,57.8509x68.944,51.6219x73.7237,45x77.9423,38.0356x81.5677,30.7818x84.5723,23.2937x86.9333,15.6283x88.6327,7.84402x89.6575,5.51091e-15x90,-7.84402x89.6575,-15.6283x88.6327,-23.2937x86.9333,-30.7818x84.5723,-38.0356x81.5677,-45x77.9423,-51.6219x73.7237,-57.8509x68.944,-63.6396x63.6396,-68.944x57.8509,-73.7237x51.6219,-77.9423x45,-81.5677x38.0356,-84.5723x30.7818,-86.9333x23.2937,-88.6327x15.6283,-89.6575x7.84402,-90x1.10218e-14,-89.6575x-7.84402,-88.6327x-15.6283,-86.9333x-23.2937,-84.5723x-30.7818,-81.5677x-38.0356,-77.9423x-45,-73.7237x-51.6219,-68.944x-57.8509,-63.6396x-63.6396,-57.8509x-68.944,-51.6219x-73.7237,-45x-77.9423,-38.0356x-81.5677,-30.7818x-84.5723,-23.2937x-86.9333,-15.6283x-88.6327,-7.84402x-89.6575,-1.65327e-14x-90,7.84402x-89.6575,15.6283x-88.6327,23.2937x-86.9333,30.7818x-84.5723,38.0356x-81.5677,45x-77.9423,51.6219x-73.7237,57.8509x-68.944,63.6396x-63.6396,68.944x-57.8509,73.7237x-51.6219,77.9423x-45,81.5677x-38.0356,84.5723x-30.7818,86.9333x-23.2937,88.6327x-15.6283,89.6575x-7.84402,90x-2.20436e-14
@@ -10,11 +10,11 @@ cooling_tube_retraction = 91.5
 default_filament_profile = ""
 default_print_profile = 
 deretract_speed = 0
-end_gcode = M104 S0 ; turn off hotend temperature\nM190 S0; turn off bed temperature\nM106; hotend fan full blast\nG28; home \nM84; disable motors\nG4 S10; wait 10 seconds for hotend cooldown\n; play some tunes:\n;Mission Impossible\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2637 P75\nM300 S2793 P75\nM300 S2959 P75\nM300 S3135 P75\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S1864 P150\nM300 S0 P150\nM300 S2093 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S2793 P150\nM300 S0 P150\nM300 S2959 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S1864 P150\nM300 S0 P150\nM300 S2093 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S2793 P150\nM300 S0 P150\nM300 S2959 P150\nM300 S0 P150\nM300 S1864 P150\nM300 S3135 P150\nM300 S2349 P1200\nM300 S0 P75\nM300 S1864 P150\nM300 S3135 P150\nM300 S2217 P1200\nM300 S0 P75\nM300 S1864 P150\nM300 S3135 P150\nM300 S2093 P1200\nM300 S0 P150\nM300 S932 P150\nM300 S2093 P150\n; end of tune\nG4 S60; wait another 2 Minutes for hotend cooldown\nM107; hotend fan off
+end_gcode = M104 S0 ; turn off hotend temperature\nM190 S0; turn off bed temperature\nM106; hotend fan full blast\nG28; home \nM84; disable motors\nG4 S10; wait 10 seconds for hotend cooldown\n; play some tunes:\n;Mission Impossible\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2637 P75\nM300 S2793 P75\nM300 S2959 P75\nM300 S3135 P75\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S1864 P150\nM300 S0 P150\nM300 S2093 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S2793 P150\nM300 S0 P150\nM300 S2959 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S1864 P150\nM300 S0 P150\nM300 S2093 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S2793 P150\nM300 S0 P150\nM300 S2959 P150\nM300 S0 P150\nM300 S1864 P150\nM300 S3135 P150\nM300 S2349 P1200\nM300 S0 P75\nM300 S1864 P150\nM300 S3135 P150\nM300 S2217 P1200\nM300 S0 P75\nM300 S1864 P150\nM300 S3135 P150\nM300 S2093 P1200\nM300 S0 P150\nM300 S932 P150\nM300 S2093 P150\n; end of tune\nG4 S120; wait another 2 Minutes for hotend cooldown\nM107; hotend fan off
 extra_loading_move = -2
 extruder_colour = #019B9B
 extruder_offset = 0x0
-gcode_flavor = marlin
+gcode_flavor = marlin2
 high_current_on_filament_swap = 0
 host_type = octoprint
 inherits = 
@@ -23,6 +23,7 @@ machine_limits_usage = emit_to_gcode
 machine_max_acceleration_e = 10000,5000
 machine_max_acceleration_extruding = 1500,1250
 machine_max_acceleration_retracting = 1500,1250
+machine_max_acceleration_travel = 1500,1250
 machine_max_acceleration_x = 9000,9000
 machine_max_acceleration_y = 9000,9000
 machine_max_acceleration_z = 9000,9000
@@ -37,9 +38,9 @@ machine_max_jerk_z = 9,9
 machine_min_extruding_rate = 0,0
 machine_min_travel_rate = 0,0
 max_layer_height = 0
-max_print_height = 196
+max_print_height = 190
 min_layer_height = 0.1
-nozzle_diameter = 0.4
+nozzle_diameter = 0.6
 parking_pos_retraction = 92
 pause_print_gcode = M601
 print_host = 
@@ -62,12 +63,13 @@ retract_lift_above = 0
 retract_lift_below = 150
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
-retract_speed = 35
+retract_speed = 37.5
 silent_mode = 1
 single_extruder_multi_material = 0
-start_gcode = G28 ; home all axes\nM140 S[first_layer_bed_temperature] ; set bed final temp\nG1 X0 Y0 Z100 F4000 ; safe position\nG1 X0 Y-50 Z5 F4000 ; lift nozzle\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\nM104 S[first_layer_temperature] ; set extruder final temp\nM109 S[first_layer_temperature] ; wait for extruder final temp\nG1 X0 Y-45 Z0.3 F3000 ; move down\n;G1 Z0.5; lift\nG92 E0\n{if perimeter_speed >= 75}M900 K0; Disable LINEAR_ADVANCE for speed's sake!\n;{elsif perimeter_speed >= 65}M900 K0.2; reduced LINEAR_ADVANCE because of higher speeds\n{else}M900 K0.38; LINEAR_ADVANCE high quality preset\n{endif}
+start_gcode = G28 ; home all axes\nM140 S[first_layer_bed_temperature] ; set bed final temp\nG1 X0 Y0 Z100 F4000 ; safe position\nG1 X0 Y-50 Z25 F4000 ; lift nozzle\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\nM104 S[first_layer_temperature] ; set extruder final temp\nM109 S[first_layer_temperature] ; wait for extruder final temp\nG1 X0 Y-45 Z0.3 F3000 ; move down\n;G1 Z0.5; lift\nG92 E0\n;{if perimeter_speed >= 75}M900 K0; Disable LINEAR_ADVANCE for speed's sake!\n;{elsif perimeter_speed >= 60}M900 K0.1; reduced LINEAR_ADVANCE because of medium speeds\n;{else}M900 K0.2; LINEAR_ADVANCE high quality preset\n; qualitywise ideal K would be somewhere around 0.38, but this slows the printer down at a unacceptable rate\nM900 K0  ;disabled linear advance alltogether, because it really hurts the printer and makes very screecy noises\n;{endif}
 template_custom_gcode = 
 thumbnails = 
+thumbnails_format = PNG
 toolchange_gcode = 
 use_firmware_retraction = 0
 use_relative_e_distances = 0
diff --git a/PrusaSlicer/vendor/PrusaResearch.idx b/PrusaSlicer/vendor/PrusaResearch.idx
deleted file mode 100644
index 47c1b7e..0000000
--- a/PrusaSlicer/vendor/PrusaResearch.idx
+++ /dev/null
@@ -1,216 +0,0 @@
-min_slic3r_version = 2.5.0-alpha0
-1.5.2 Added SLA material profiles.
-1.5.1 Renamed filament type "NYLON" to "PA". Updated Adura X profile. Updated PETG fan settings for Prusa MINI (removed fan ramp up).
-1.5.0 Updated arachne parameters. Added profiles for Jessie filaments.
-1.5.0-alpha1 Added filament profile for Prusament PA11 Carbon Fiber. Added profiles for multiple 3D-Fuel filaments.
-1.5.0-alpha0 Added parameters for Arachne perimeter generator. Changed default seam position. Updated output filename format.
-min_slic3r_version = 2.4.0-rc
-1.4.8 Added filament and SLA material profiles. Updated settings.
-1.4.7 Added filament profile for Prusament PA11 Carbon Fiber. Added profiles for multiple 3D-Fuel filaments.
-1.4.6 Added SLA materials. Updated filament profiles. 
-1.4.5 Added MMU2/S profiles for 0.25mm nozzle. Updated FW version. Enabled g-code thumbnails for MK3 family printers. Updated end g-code.
-1.4.4 Added multiple Fiberlogy filament profiles. Updated Extrudr filament profiles.
-1.4.3 Added new filament profiles and SLA materials.
-1.4.2 Added SLA material profiles.
-1.4.1 Updated firmware version.
-1.4.0 Updated for the PrusaSlicer 2.4.0-rc release. Updated SLA material colors.
-min_slic3r_version = 2.4.0-beta2
-1.4.0-beta3 Added material profiles for Prusament Resins.
-1.4.0-beta2 Added SLA material colors. Updated BASF filament profiles.
-min_slic3r_version = 2.4.0-beta0
-1.4.0-beta1 Updated pad wall slope angle for SLA printers. Updated Filatech Filacarbon profile for Prusa MINI. 
-1.4.0-beta0 Added multiple Filatech and BASF filament profiles. Added material profiles for SL1S.
-min_slic3r_version = 2.4.0-alpha0
-1.4.0-alpha8 Added material profiles for Prusament Resin. Detect bridging perimeters enabled by default. 
-1.4.0-alpha7 Updated brim_separation value. Updated Prusa MINI end g-code. Added Filamentworld filament profiles. 
-1.4.0-alpha6 Added nozzle priming after M600. Added nozzle diameter checks for 0.8 nozzle printer profiles. Updated FW version. Increased number of top solid infill layers (0.2 layer height).
-1.4.0-alpha5 Added multiple add:north and Extrudr filament profiles. Updated support head settings (SL1S).
-1.4.0-alpha4 Decreased Area Fill (SL1S).
-1.4.0-alpha3 Updated SL1S tilt times.
-1.4.0-alpha2 Updated Prusa MINI machine limits.
-1.4.0-alpha1 Added new SL1S resin profiles.
-1.4.0-alpha0 Bumped up config version.
-1.3.0-alpha2 Added SL1S SPEED profiles.
-1.3.0-alpha1 Added Prusament PCCF. Increased travel acceleration for Prusa MINI. Updated start g-code for Prusa MINI. Added multiple add:north and Extrudr filament profiles. Updated Z travel speed values.
-1.3.0-alpha0 Disabled thick bridges, updated support settings.
-min_slic3r_version = 2.3.2-alpha0
-1.3.7 Updated firmware version.
-1.3.6 Updated firmware version.
-1.3.5 Added material profiles for Prusament Resins.
-1.3.4 Added material profiles for new Prusament Resins. Added profiles for multiple BASF filaments.
-1.3.3 Added multiple profiles for Filatech filaments. Added material profiles for SL1S SPEED. Updated SLA print settings.
-1.3.2 Added material profiles for Prusament Resin.
-1.3.1 Added multiple add:north and Extrudr filament profiles. Updated support head settings (SL1S).
-1.3.0 Added SL1S SPEED profiles.
-min_slic3r_version = 2.3.0-rc1
-1.2.12 Updated firmware version.
-1.2.11 Updated firmware version.
-1.2.10 Added multiple profiles for Filatech filaments. Updated SLA print settings (pad wall slope angle).
-1.2.9 Added material profiles for Prusament Resin.
-1.2.8 Added multiple add:north and Extrudr filament profiles.
-1.2.7 Updated "Prusament PC Blend Carbon Fiber" profile for Prusa MINI.
-1.2.6 Added filament profile for "Prusament PC Blend Carbon Fiber".
-1.2.5 Updated firmware version. Added filament profiles. Various improvements.
-1.2.4 Updated cost/density values in filament settings. Various changes in print settings.
-1.2.3 Updated firmware version. Updated end g-code in MMU2 printer profiles.
-1.2.2 Added Prusament PVB filament profile. Added 0.8mm nozzle profiles. 
-1.2.1 Updated FW version for MK2.5 family printers.
-1.2.0 Added full_fan_speed_layer value for PETG. Increased support interface spacing for 0.6mm nozzle profiles. Updated firmware version.
-min_slic3r_version = 2.3.0-beta2
-1.2.0-beta1 Updated end g-code. Added full_fan_speed_layer values.
-min_slic3r_version = 2.3.0-beta0
-1.2.0-beta0 Adjusted infill anchor limits. Added filament spool weights. 
-min_slic3r_version = 2.3.0-alpha4
-1.2.0-alpha1 Renamed MK3S and MINI printer profiles. Updated end g-code (MINI). Added new SLA materials and filament profiles.
-1.2.0-alpha0 Added filament spool weights
-min_slic3r_version = 2.2.0-alpha3
-1.1.16 Updated firmware version.
-1.1.15 Updated firmware version.
-1.1.14 Updated firmware version.
-1.1.13 Updated firmware version. Updated end g-code in MMU2 printer profiles.
-1.1.12 Added Prusament PVB filament profile. Added 0.8mm nozzle profiles. 
-1.1.11 Renamed MK3S and MINI printer profiles. Updated end g-code (MINI). Added new SLA materials and filament profiles.
-1.1.10 Updated firmware version.
-1.1.9 Updated K values in filament profiles (linear advance). Added new filament profiles and SLA materials.
-1.1.8 Updated start/end g-code scripts for MK3 family printer profiles (reduced extruder motor current for some print profiles). Added new filament and SLA material profiles.
-1.1.7 Updated end g-code for MMU2 Single printer profiles. Added/updated filament and SLA material profiles.
-1.1.6 Updated firmware version for MK2.5/S and MK3/S.
-1.1.5 Updated MMU1 specific retraction settings for Prusament PC Blend
-1.1.4 Added Prusament PC Blend filament profile.
-1.1.3 Added SLA material and filament profile
-1.1.2 Added renamed_from fields for PETG filaments to indicate that they were renamed from PET.
-1.1.1 Added Verbatim and Fiberlogy PETG filament profiles. Updated auto cooling settings for ABS.
-1.1.1-beta Updated for PrusaSlicer 2.2.0-beta
-1.1.1-alpha4 Extended list of default filaments to be installed, top/bottom_solid_min_thickness defined, infill_acceleration changed etc
-1.1.1-alpha3 Print bed textures are now configurable from the Preset Bundle. Requires PrusaSlicer 2.2.0-alpha3 and newer.
-# The following line (max_slic3r_version) forces the users of PrusaSlicer 2.2.0-alpha3 and newer to update the profiles to 1.1.1-alpha3 and newer,
-# so they will see the print bed.
-max_slic3r_version = 2.2.0-alpha2
-min_slic3r_version = 2.2.0-alpha0
-1.1.1-alpha2 Bumped up config version, so our in house customer will get updated profiles.
-1.1.0 Filament aliases, Creality profiles and other goodies for PrusaSlicer 2.2.0-alpha0
-min_slic3r_version = 2.1.1-beta0
-1.0.12 Updated firmware version.
-1.0.11 Updated firmware version.
-1.0.10 Updated firmware version for MK2.5/S and MK3/S.
-1.0.9 Updated firmware version for MK2.5/S and MK3/S.
-1.0.8 Various changes in FFF profiles, new filaments/materials added. See changelog.
-1.0.7 Updated layer height limits for MINI
-1.0.6 Added Prusa MINI profiles
-min_slic3r_version = 2.1.0-alpha0
-1.0.5 Added SLA materials
-1.0.4 Updated firmware version and 0.25mm nozzle profiles
-1.0.3 Added filament profiles
-1.0.2 Added SLA materials
-1.0.1 Updated MK3 firmware version check to 3.8.0, new soluble support profiles for 0.6mm nozzle diameter MMU2S printers.
-1.0.0 Updated end G-code for the MMU2 profiles to lift the extruder at the end of print. Wipe tower bridging distance was made smaller for soluble supports.
-1.0.0-beta1 Updated color for the ASA filaments to differ from the other filaments. Single extruder printers now have no extruder color assigned, obects and toolpaths will be colored with the color of the active filament.
-1.0.0-beta0 Printer model checks in start G-codes, ASA filament profiles, limits on min / max SL1 exposition times
-1.0.0-alpha2 Printer model and nozzle diameter check
-1.0.0-alpha1 Added Prusament ASA profile
-1.0.0-alpha0 Filament specific retract for PET and similar copolymers, and for FLEX
-min_slic3r_version = 1.42.0-alpha6
-0.8.11 Updated firmware version.
-0.8.10 Updated firmware version.
-0.8.9 Updated firmware version for MK2.5/S and MK3/S.
-0.8.8 Updated firmware version for MK2.5/S and MK3/S.
-0.8.7 Updated firmware version
-0.8.6 Updated firmware version for MK2.5/S and MK3/S
-0.8.5 Updated SL1 printer and material settings
-0.8.4 Added Prusament ASA profile
-0.8.3 FW version and SL1 materials update
-0.8.2 FFF and SL1 settings update
-0.8.1 Output settings and SLA materials update
-0.8.0 Updated for the PrusaSlicer 2.0.0 final release
-0.8.0-rc2 Updated firmware versions for MK2.5/S and MK3/S
-0.8.0-rc1 Updated SLA profiles
-0.8.0-rc Updated for the PrusaSlicer 2.0.0-rc release
-0.8.0-beta4 Updated SLA profiles
-0.8.0-beta3 Updated SLA profiles
-0.8.0-beta2 Updated SLA profiles
-0.8.0-beta1 Updated SLA profiles
-0.8.0-beta Updated SLA profiles
-0.8.0-alpha9 Updated SLA and FFF profiles
-0.8.0-alpha8 Updated SLA profiles
-0.8.0-alpha7 Updated SLA profiles
-0.8.0-alpha6 Updated SLA profiles
-min_slic3r_version = 1.42.0-alpha
-0.8.0-alpha Updated SLA profiles
-0.4.0-alpha4 Updated SLA profiles
-0.4.0-alpha3 Update of SLA profiles
-0.4.0-alpha2 First SLA profiles
-min_slic3r_version = 1.41.3-alpha
-0.4.12 Updated firmware version for MK2.5/S and MK3/S.
-0.4.11 Updated firmware version for MK2.5/S and MK3/S.
-0.4.10 Updated firmware version
-0.4.9 Updated firmware version for MK2.5/S and MK3/S
-0.4.8 MK2.5/3/S FW update
-0.4.7 MK2/S/MMU FW update
-0.4.6 Updated firmware versions for MK2.5/S and MK3/S
-0.4.5 Enabled remaining time support for MK2/S/MMU1
-0.4.4 Changelog: https://github.com/prusa3d/Slic3r-settings/blob/master/live/PrusaResearch/changelog.txt
-0.4.3 Changelog: https://github.com/prusa3d/Slic3r-settings/blob/master/live/PrusaResearch/changelog.txt
-0.4.2 Changelog: https://github.com/prusa3d/Slic3r-settings/blob/master/live/PrusaResearch/changelog.txt
-0.4.1 New MK2.5S and MK3S FW versions
-0.4.0 Changelog: https://github.com/prusa3d/Slic3r-settings/blob/master/live/PrusaResearch/changelog.txt 
-min_slic3r_version = 1.41.1
-0.3.11 Updated firmware version for MK2.5/S and MK3/S.
-0.3.10 Updated firmware version
-0.3.9 Updated firmware version for MK2.5/S and MK3/S
-0.3.8 MK2.5/3/S FW update
-0.3.7 MK2/S/MMU FW update
-0.3.6 Updated firmware versions for MK2.5 and MK3
-0.3.5 New MK2.5 and MK3 FW versions
-0.3.4 Changelog: https://github.com/prusa3d/Slic3r-settings/blob/master/live/PrusaResearch/changelog.txt 
-0.3.3 Prusament PETG released
-0.3.2 New MK2.5 and MK3 FW versions
-0.3.1 New MK2.5 and MK3 FW versions
-0.3.0 New MK2.5 and MK3 FW version
-min_slic3r_version = 1.41.0-alpha
-0.2.9 New MK2.5 and MK3 FW versions
-0.2.8 New MK2.5 and MK3 FW version
-min_slic3r_version = 1.41.1
-0.2.7 New MK2.5 and MK3 FW version
-0.2.6 Added MMU2 MK2.5 settings
-min_slic3r_version = 1.41.0-alpha
-0.2.5 Prusament is out - added prusament settings
-0.2.4 Added soluble support profiles for MMU2
-0.2.3 Added materials for MMU2 single mode, edited MK3 xy stealth feedrate limit
-0.2.2 Edited MMU2 Single mode purge line
-0.2.1 Added PET and BVOH settings for MMU2
-0.2.0-beta5 Fixed MMU1 ramming parameters
-0.2.0-beta4 Added filament loading speed at start, increased minimal purge on wipe tower
-0.2.0-beta3 Edited ramming parameters and filament cooling moves for MMU2
-0.2.0-beta2 Edited first layer speed and wipe tower position
-0.2.0-beta Removed limit on the MK3MMU2 height, added legacy M204 S T format to the MK2 profiles
-0.2.0-alpha8 Added filament_load/unload_time for the PLA/ABS MMU2 filament presets.
-0.2.0-alpha7 Vojtech's fix the incorrect *MK3* references
-0.2.0-alpha6 Jindra's way to fix the 0.2.0-alpha5 version
-0.2.0-alpha5 Bumped up firmware versions for MK2.5/MK3 to 3.3.1, disabled priming areas for MK3MMU2
-0.2.0-alpha4 Extended the custom start/end G-codes of the MMU2.0 printers for no priming towers.
-0.2.0-alpha3 Adjusted machine limits for time estimates, added filament density and cost
-0.2.0-alpha2 Renamed the key MK3SMMU to MK3MMU2, added a generic PLA MMU2 material
-0.2.0-alpha1 added initial profiles for the i3 MK3 Multi Material Upgrade 2.0
-0.2.0-alpha moved machine limits from the start G-code to the new print profile parameters
-min_slic3r_version = 1.40.0
-0.1.18 Updated firmware version
-0.1.17 Updated firmware version for MK2.5/S and MK3/S
-0.1.16 MK2.5/3/S FW update
-0.1.15 MK2/S/MMU FW update
-0.1.14 Updated firmware versions for MK2.5 and MK3
-0.1.13 New MK2.5 and MK3 FW versions
-0.1.12 New MK2.5 and MK3 FW versions
-0.1.11 fw version changed to 3.3.1
-0.1.10 MK3 jerk and acceleration update
-0.1.9 edited support extrusion width for 0.25 and 0.6 nozzles
-0.1.8 extrusion width for 0,25, 0.6 and variable layer height fixes
-0.1.7 Fixed errors in 0.25mm and 0.6mm profiles
-0.1.6 Split the MK2.5 profile from the MK2S
-min_slic3r_version = 1.40.0-beta
-0.1.5 fixed printer_variant fields for the i3 MK3 0.25 and 0.6mm nozzles
-0.1.4 edited fw version, added z-raise after print
-min_slic3r_version = 1.40.0-alpha
-0.1.3 Fixed an incorrect position of the max_print_height parameter
-0.1.2 Wipe tower changes
-0.1.1 Minor print speed adjustments
-0.1.0 Initial
diff --git a/PrusaSlicer/vendor/PrusaResearch.ini b/PrusaSlicer/vendor/PrusaResearch.ini
deleted file mode 100644
index 17d8486..0000000
--- a/PrusaSlicer/vendor/PrusaResearch.ini
+++ /dev/null
@@ -1,9625 +0,0 @@
-# Print profiles for the Prusa Research printers.
-
-[vendor]
-# Vendor name will be shown by the Config Wizard.
-name = Prusa Research
-# Configuration version of this file. Config file will only be installed, if the config_version differs.
-# This means, the server may force the PrusaSlicer configuration to be downgraded.
-config_version = 1.5.1
-# Where to get the updates from?
-config_update_url = https://files.prusa3d.com/wp-content/uploads/repository/PrusaSlicer-settings-master/live/PrusaResearch/
-changelog_url = https://files.prusa3d.com/?latest=slicer-profiles&lng=%1%
-
-# The printer models will be shown by the Configuration Wizard in this order,
-# also the first model installed & the first nozzle installed will be activated after install.
-# Printer model name will be shown by the installation wizard.
-
-[printer_model:MINI]
-name = Original Prusa MINI && MINI+
-variants = 0.4; 0.25; 0.6; 0.8
-technology = FFF
-family = MINI
-bed_model = mini_bed.stl
-bed_texture = mini.svg
-default_materials = Generic PLA; Generic ABS @MINI; Generic PETG @MINI; Prusament PLA; Prusament PETG @MINI; Prusament ASA @MINI; Prusament PC Blend @MINI; Prusament PC Blend Carbon Fiber @MINI; Prusament PVB
-
-[printer_model:MK3S]
-name = Original Prusa i3 MK3S && MK3S+
-variants = 0.4; 0.25; 0.6; 0.8
-technology = FFF
-family = MK3
-bed_model = mk3_bed.stl
-bed_texture = mk3.svg
-default_materials = Generic PLA; Generic ABS; Generic PETG; Prusament PLA; Prusament PETG; Prusament ASA; Prusament PC Blend; Prusament PC Blend Carbon Fiber; Prusament PVB; Prusament PA11 Carbon Fiber
-
-[printer_model:MK3]
-name = Original Prusa i3 MK3
-variants = 0.4; 0.25; 0.6; 0.8
-technology = FFF
-family = MK3
-bed_model = mk3_bed.stl
-bed_texture = mk3.svg
-default_materials = Generic PLA; Generic ABS; Generic PETG; Prusament PLA; Prusament PETG; Prusament ASA; Prusament PC Blend; Prusament PC Blend Carbon Fiber; Prusament PVB; Prusament PA11 Carbon Fiber
-
-[printer_model:MK3SMMU2S]
-name = Original Prusa i3 MK3S && MK3S+ MMU2S
-variants = 0.4; 0.25; 0.6; 0.8
-technology = FFF
-family = MK3
-bed_model = mk3_bed.stl
-bed_texture = mk3.svg
-default_materials = Generic PLA; Generic ABS; Generic PETG; Prusament PLA @MMU2; Prusament PETG @MMU2; Prusament ASA @MMU2; Verbatim BVOH @MMU2; Prusament PC Blend @MMU2; Prusament PC Blend Carbon Fiber @MMU2; Prusament PVB @MMU2
-
-[printer_model:MK3MMU2]
-name = Original Prusa i3 MK3 MMU2
-variants = 0.4; 0.25; 0.6; 0.8
-technology = FFF
-family = MK3
-bed_model = mk3_bed.stl
-bed_texture = mk3.svg
-default_materials = Generic PLA; Generic ABS; Generic PETG; Prusament PLA @MMU2; Prusament PETG @MMU2; Prusament ASA @MMU2; Verbatim BVOH @MMU2; Prusament PC Blend @MMU2; Prusament PC Blend Carbon Fiber @MMU2; Prusament PVB @MMU2
-
-[printer_model:MK2.5S]
-name = Original Prusa i3 MK2.5S
-variants = 0.4; 0.25; 0.6; 0.8
-technology = FFF
-family = MK2.5
-bed_model = mk3_bed.stl
-bed_texture = mk3.svg
-default_materials = Generic PLA; Generic ABS; Generic PETG; Prusament PLA; Prusament PETG; Prusament ASA; Prusament PC Blend; Prusament PC Blend Carbon Fiber; Prusament PVB; Prusament PA11 Carbon Fiber @MK2
-
-[printer_model:MK2.5]
-name = Original Prusa i3 MK2.5
-variants = 0.4; 0.25; 0.6; 0.8
-technology = FFF
-family = MK2.5
-bed_model = mk3_bed.stl
-bed_texture = mk3.svg
-default_materials = Generic PLA; Generic ABS; Generic PETG; Prusament PLA; Prusament PETG; Prusament ASA; Prusament PC Blend; Prusament PC Blend Carbon Fiber; Prusament PVB; Prusament PA11 Carbon Fiber @MK2
-
-[printer_model:MK2.5SMMU2S]
-name = Original Prusa i3 MK2.5S MMU2S
-variants = 0.4; 0.25; 0.6; 0.8
-technology = FFF
-family = MK2.5
-bed_model = mk3_bed.stl
-bed_texture = mk3.svg
-default_materials = Generic PLA; Generic ABS; Generic PETG; Prusament PLA @MMU2; Prusament PETG @MMU2; Prusament ASA @MMU2; Verbatim BVOH @MMU2; Prusament PC Blend @MMU2; Prusament PC Blend Carbon Fiber @MMU2; Prusament PVB @MMU2
-
-[printer_model:MK2.5MMU2]
-name = Original Prusa i3 MK2.5 MMU2
-variants = 0.4; 0.25; 0.6; 0.8
-technology = FFF
-family = MK2.5
-bed_model = mk3_bed.stl
-bed_texture = mk3.svg
-default_materials = Generic PLA; Generic ABS; Generic PETG; Prusament PLA @MMU2; Prusament PETG @MMU2; Prusament ASA @MMU2; Verbatim BVOH @MMU2; Prusament PC Blend @MMU2; Prusament PC Blend Carbon Fiber @MMU2; Prusament PVB @MMU2
-
-[printer_model:MK2S]
-name = Original Prusa i3 MK2S
-variants = 0.4; 0.25; 0.6
-technology = FFF
-family = MK2
-bed_model = mk2_bed.stl
-bed_texture = mk2.svg
-default_materials = Generic PLA; Generic ABS; Generic PETG; Prusament PLA; Prusament PETG; Prusament ASA; Prusament PC Blend; Prusament PC Blend Carbon Fiber; Prusament PVB; Prusament PA11 Carbon Fiber @MK2
-
-[printer_model:MK2SMM]
-name = Original Prusa i3 MK2S MMU1
-variants = 0.4; 0.6
-technology = FFF
-family = MK2
-bed_model = mk2_bed.stl
-bed_texture = mk2.svg
-default_materials =  Generic PLA; Generic ABS; Generic PETG @MMU1; Prusament PLA; Prusament PETG @MMU1; Prusament ASA; Prusament PC Blend; Prusament PC Blend Carbon Fiber; Prusament PVB
-
-[printer_model:SL1]
-name = Original Prusa SL1
-variants = default
-technology = SLA
-family = SL1
-bed_model = sl1_bed.stl
-bed_texture = sl1.svg
-default_materials = Prusa Orange Tough @0.05; Prusament Resin Tough Prusa Orange @0.05
-
-[printer_model:SL1S]
-name = Original Prusa SL1S SPEED
-variants = default
-technology = SLA
-family = SL1
-bed_model = sl1s_bed.stl
-bed_texture = sl1s.svg
-default_materials = Prusa Orange Tough @0.05 SL1S; Prusament Resin Tough Prusa Orange @0.05 SL1S
-
-# All presets starting with asterisk, for example *common*, are intermediate and they will
-# not make it into the user interface.
-
-# Common print presets
-
-[print:*common*]
-avoid_crossing_perimeters = 0
-thick_bridges = 0
-bridge_acceleration = 1000
-bridge_angle = 0
-bridge_flow_ratio = 1
-bridge_speed = 25
-brim_width = 0
-brim_separation = 0.1
-clip_multipart_objects = 1
-compatible_printers = 
-complete_objects = 0
-default_acceleration = 1000
-dont_support_bridges = 0
-elefant_foot_compensation = 0.2
-ensure_vertical_shell_thickness = 1
-external_fill_pattern = rectilinear
-external_perimeters_first = 0
-external_perimeter_extrusion_width = 0.45
-extra_perimeters = 0
-extruder_clearance_height = 20
-extruder_clearance_radius = 45
-extrusion_width = 0.45
-fill_angle = 45
-fill_density = 20%
-fill_pattern = cubic
-first_layer_acceleration = 800
-first_layer_extrusion_width = 0.42
-first_layer_height = 0.2
-first_layer_speed = 20
-gap_fill_speed = 40
-gcode_comments = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0.45
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap = 25%
-interface_shells = 0
-max_print_speed = 100
-max_volumetric_extrusion_rate_slope_negative = 0
-max_volumetric_extrusion_rate_slope_positive = 0
-max_volumetric_speed = 0
-min_skirt_length = 4
-notes = 
-overhangs = 1
-only_retract_when_crossing_perimeters = 0
-ooze_prevention = 0
-output_filename_format = {input_filename_base}_{layer_height}mm_{initial_filament_type}_{printer_model}_{print_time}.gcode
-perimeters = 2
-perimeter_extruder = 1
-perimeter_extrusion_width = 0.45
-post_process = 
-print_settings_id = 
-raft_layers = 0
-raft_first_layer_density = 90%
-resolution = 0
-seam_position = aligned
-single_extruder_multi_material_priming = 1
-skirts = 1
-skirt_distance = 2
-skirt_height = 3
-small_perimeter_speed = 25
-solid_infill_below_area = 0
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 0.45
-spiral_vase = 0
-standby_temperature_delta = -5
-support_material = 0
-support_material_extruder = 0
-support_material_extrusion_width = 0.35
-support_material_interface_extruder = 0
-support_material_angle = 0
-support_material_buildplate_only = 0
-support_material_enforce_layers = 0
-support_material_contact_distance = 0.2
-raft_contact_distance = 0.2
-support_material_interface_contact_loops = 0
-support_material_interface_layers = 2
-support_material_interface_spacing = 0.2
-support_material_interface_speed = 80%
-support_material_pattern = rectilinear
-support_material_spacing = 2
-support_material_speed = 50
-support_material_synchronize_layers = 0
-support_material_threshold = 50
-support_material_with_sheath = 0
-support_material_xy_spacing = 60%
-support_material_bottom_interface_layers = 0
-thin_walls = 0
-top_infill_extrusion_width = 0.45
-top_solid_infill_speed = 40
-travel_speed = 180
-travel_speed_z = 12
-wipe_tower = 1
-wipe_tower_bridging = 10
-wipe_tower_rotation_angle = 0
-wipe_tower_width = 60
-wipe_tower_x = 170
-wipe_tower_y = 140
-xy_size_compensation = 0
-top_solid_min_thickness = 0.7
-bottom_solid_min_thickness = 0.5
-gcode_label_objects = 1
-infill_anchor = 2.5
-infill_anchor_max = 12
-wall_transition_angle = 10
-wall_transition_filter_deviation = 25%
-wall_transition_length = 0.4
-wall_distribution_count = 1
-min_bead_width = 85%
-
-[print:*MK3*]
-fill_pattern = grid
-single_extruder_multi_material_priming = 0
-travel_speed = 180
-wipe_tower_x = 170
-wipe_tower_y = 125
-
-[print:*MK306*]
-inherits = *MK3*
-fill_pattern = gyroid
-fill_density = 15%
-
-[print:*MINI*]
-fill_pattern = grid
-travel_speed = 150
-wipe_tower = 0
-default_acceleration = 1000
-first_layer_acceleration = 800
-infill_acceleration = 1000
-bridge_acceleration = 1000
-support_material_speed = 40
-max_print_speed = 150
-extruder_clearance_height = 20
-extruder_clearance_radius = 35
-
-[print:*0.25nozzle*]
-elefant_foot_compensation = 0
-external_perimeter_extrusion_width = 0.25
-extrusion_width = 0.25
-first_layer_extrusion_width = 0.3
-infill_extrusion_width = 0.25
-perimeter_extrusion_width = 0.25
-solid_infill_extrusion_width = 0.25
-top_infill_extrusion_width = 0.25
-support_material_extrusion_width = 0.25
-support_material_interface_layers = 0
-support_material_interface_spacing = 0.15
-support_material_spacing = 1
-support_material_xy_spacing = 150%
-support_material_contact_distance = 0.1
-output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{initial_filament_type}_{printer_model}_{print_time}.gcode
-thick_bridges = 0
-bridge_flow_ratio = 1
-bridge_speed = 20
-wipe_tower_bridging = 6
-wall_transition_angle = 10
-wall_transition_filter_deviation = 25%
-wall_transition_length = 0.25
-wall_distribution_count = 1
-min_bead_width = 85%
-
-[print:*0.25nozzleMK3*]
-inherits = *0.25nozzle*
-perimeter_speed = 30
-external_perimeter_speed = 20
-small_perimeter_speed = 20
-infill_speed = 45
-solid_infill_speed = 45
-top_solid_infill_speed = 30
-support_material_speed = 40
-gap_fill_speed = 30
-perimeter_acceleration = 500
-infill_acceleration = 1000
-bridge_acceleration = 500
-first_layer_acceleration = 500
-default_acceleration = 1000
-max_print_speed = 80
-perimeters = 3
-fill_pattern = grid
-fill_density = 20%
-wipe_tower_bridging = 6
-
-[print:*0.25nozzleMINI*]
-inherits = *0.25nozzleMK3*
-infill_speed = 40
-solid_infill_speed = 40
-infill_acceleration = 800
-first_layer_acceleration = 500
-
-[print:*0.6nozzle*]
-external_perimeter_extrusion_width = 0.61
-extrusion_width = 0.67
-first_layer_extrusion_width = 0.65
-infill_extrusion_width = 0.7
-perimeter_extrusion_width = 0.65
-solid_infill_extrusion_width = 0.65
-top_infill_extrusion_width = 0.6
-support_material_extrusion_width = 0.55
-support_material_contact_distance = 0.15
-support_material_xy_spacing = 80%
-support_material_interface_spacing = 0.3
-output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{initial_filament_type}_{printer_model}_{print_time}.gcode
-infill_anchor_max = 15
-top_solid_min_thickness = 0.9
-bottom_solid_min_thickness = 0.6
-thick_bridges = 1
-bridge_flow_ratio = 0.95
-bridge_speed = 25
-wall_transition_angle = 10
-wall_transition_filter_deviation = 25%
-wall_transition_length = 0.6
-wall_distribution_count = 1
-min_bead_width = 85%
-
-[print:*0.6nozzleMK3*]
-inherits = *0.6nozzle*
-external_perimeter_extrusion_width = 0.65
-extrusion_width = 0.65
-infill_extrusion_width = 0.65
-thick_bridges = 0
-
-[print:*0.6nozzleMINI*]
-inherits = *0.6nozzleMK3*
-infill_extrusion_width = 0.68
-solid_infill_extrusion_width = 0.68
-fill_pattern = gyroid
-fill_density = 15%
-travel_speed = 150
-perimeter_acceleration = 800
-infill_acceleration = 1000
-bridge_acceleration = 1000
-first_layer_acceleration = 800
-default_acceleration = 1250
-support_material_speed = 40
-support_material_interface_speed = 100%
-
-[print:*0.8nozzle*]
-external_perimeter_extrusion_width = 0.9
-extrusion_width = 0.9
-first_layer_extrusion_width = 0.9
-infill_extrusion_width = 0.9
-perimeter_extrusion_width = 0.9
-solid_infill_extrusion_width = 0.9
-top_infill_extrusion_width = 0.8
-support_material_extrusion_width = 0.7
-support_material_contact_distance = 0.25
-support_material_interface_spacing = 0.4
-support_material_interface_speed = 100%
-support_material_spacing = 2
-support_material_xy_spacing = 80%
-support_material_threshold = 50
-output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{initial_filament_type}_{printer_model}_{print_time}.gcode
-fill_pattern = gyroid
-fill_density = 15%
-infill_anchor_max = 20
-top_solid_layers = 4
-bottom_solid_layers = 3
-skirt_distance = 3
-skirt_height = 2
-first_layer_height = 0.3
-infill_overlap = 30%
-bridge_speed = 22
-gap_fill_speed = 30
-bridge_flow_ratio = 0.9
-perimeter_acceleration = 800
-infill_acceleration = 1000
-bridge_acceleration = 1000
-first_layer_acceleration = 800
-default_acceleration = 1000
-top_solid_min_thickness = 1.2
-bottom_solid_min_thickness = 0.8
-single_extruder_multi_material_priming = 0
-thick_bridges = 1
-overhangs = 0
-wall_transition_angle = 10
-wall_transition_filter_deviation = 25%
-wall_transition_length = 0.8
-wall_distribution_count = 1
-min_bead_width = 85%
-
-[print:*soluble_support*]
-overhangs = 1
-skirts = 0
-support_material = 1
-support_material_contact_distance = 0
-support_material_extruder = 4
-support_material_extrusion_width = 0.45
-support_material_interface_extruder = 4
-support_material_interface_spacing = 0.1
-support_material_synchronize_layers = 1
-support_material_threshold = 80
-support_material_with_sheath = 1
-wipe_tower_bridging = 6
-support_material_interface_speed = 80%
-support_material_bottom_interface_layers = -1
-thick_bridges = 1
-
-[print:*0.05mm*]
-inherits = *common*
-layer_height = 0.05
-bottom_solid_layers = 10
-bridge_acceleration = 300
-bridge_flow_ratio = 1.15
-bridge_speed = 15
-default_acceleration = 1000
-external_perimeter_speed = 20
-fill_density = 20%
-first_layer_acceleration = 800
-gap_fill_speed = 20
-infill_acceleration = 800
-infill_speed = 30
-max_print_speed = 80
-small_perimeter_speed = 20
-solid_infill_speed = 30
-support_material_extrusion_width = 0.33
-support_material_spacing = 1.5
-support_material_contact_distance = 0.15
-raft_contact_distance = 0.15
-perimeter_acceleration = 300
-perimeter_speed = 30
-perimeters = 3
-support_material_speed = 30
-top_solid_infill_speed = 20
-top_solid_layers = 15
-
-[print:*0.07mm*]
-inherits = *0.05mm*
-layer_height = 0.07
-bottom_solid_layers = 8
-bridge_flow_ratio = 1
-fill_density = 15%
-infill_speed = 40
-solid_infill_speed = 40
-support_material_speed = 40
-top_solid_infill_speed = 30
-top_solid_layers = 11
-
-[print:*0.10mm*]
-inherits = *common*
-bottom_solid_layers = 7
-bridge_flow_ratio = 1
-bridge_speed = 20
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders==1
-layer_height = 0.1
-perimeter_acceleration = 600
-top_solid_layers = 9
-support_material_contact_distance = 0.17
-raft_contact_distance = 0.15
-
-[print:*0.15mm*]
-inherits = *common*
-bottom_solid_layers = 5
-external_perimeter_speed = 40
-infill_acceleration = 2000
-infill_speed = 60
-layer_height = 0.15
-perimeter_acceleration = 800
-perimeter_speed = 50
-solid_infill_speed = 50
-top_infill_extrusion_width = 0.4
-top_solid_layers = 8
-bridge_flow_ratio = 1
-bridge_speed = 25
-
-[print:*0.20mm*]
-inherits = *common*
-bottom_solid_layers = 4
-bridge_flow_ratio = 0.95
-external_perimeter_speed = 40
-infill_acceleration = 2000
-infill_speed = 60
-layer_height = 0.2
-perimeter_acceleration = 800
-perimeter_speed = 50
-solid_infill_speed = 50
-top_infill_extrusion_width = 0.4
-top_solid_layers = 6
-
-[print:*0.25mm*]
-inherits = *common*
-bottom_solid_layers = 4
-bridge_flow_ratio = 0.95
-external_perimeter_speed = 40
-perimeter_acceleration = 800
-layer_height = 0.25
-perimeter_speed = 50
-top_solid_layers = 4
-
-[print:*0.30mm*]
-inherits = *common*
-bottom_solid_layers = 4
-bridge_flow_ratio = 0.95
-external_perimeter_speed = 40
-infill_acceleration = 2000
-infill_speed = 60
-layer_height = 0.3
-perimeter_acceleration = 800
-perimeter_speed = 50
-solid_infill_speed = 50
-top_infill_extrusion_width = 0.4
-top_solid_layers = 4
-support_material_contact_distance = 0.3
-
-[print:*0.35mm*]
-inherits = *common*
-bottom_solid_layers = 3
-external_perimeter_extrusion_width = 0.6
-external_perimeter_speed = 40
-first_layer_extrusion_width = 0.75
-infill_acceleration = 2000
-infill_speed = 60
-layer_height = 0.35
-perimeter_acceleration = 800
-perimeter_extrusion_width = 0.65
-perimeter_speed = 50
-solid_infill_extrusion_width = 0.65
-solid_infill_speed = 60
-top_solid_infill_speed = 50
-top_solid_layers = 4
-
-[print:*0.40mm*]
-inherits = *common*
-bottom_solid_layers = 3
-external_perimeter_extrusion_width = 0.6
-external_perimeter_speed = 40
-first_layer_extrusion_width = 0.65
-infill_acceleration = 2000
-infill_speed = 60
-layer_height = 0.4
-perimeter_acceleration = 800
-perimeter_extrusion_width = 0.65
-perimeter_speed = 50
-solid_infill_extrusion_width = 0.65
-solid_infill_speed = 60
-top_solid_infill_speed = 40
-top_solid_layers = 4
-
-## MK2 family ##
-
-## MK2 - 0.4mm nozzle
-[print:0.05mm ULTRADETAIL]
-inherits = *0.05mm*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders==1
-infill_extrusion_width = 0.5
-
-[print:0.10mm DETAIL]
-inherits = *0.10mm*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders==1
-external_perimeter_speed = 40
-infill_acceleration = 2000
-infill_speed = 60
-perimeter_speed = 50
-solid_infill_speed = 50
-perimeters = 3
-bridge_acceleration = 800
-
-[print:0.15mm 100mms Linear Advance]
-inherits = *0.15mm*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4
-external_perimeter_speed = 50
-infill_speed = 100
-max_print_speed = 150
-perimeter_speed = 60
-small_perimeter_speed = 30
-solid_infill_speed = 100
-support_material_speed = 60
-top_solid_infill_speed = 70
-
-[print:0.15mm OPTIMAL]
-inherits = *0.15mm*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4
-top_infill_extrusion_width = 0.45
-
-[print:0.20mm 100mms Linear Advance]
-inherits = *0.20mm*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4
-external_perimeter_speed = 50
-infill_speed = 100
-max_print_speed = 150
-perimeter_speed = 60
-small_perimeter_speed = 30
-solid_infill_speed = 100
-support_material_speed = 60
-top_solid_infill_speed = 70
-
-[print:0.20mm NORMAL]
-inherits = *0.20mm*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4
-
-[print:0.35mm FAST]
-inherits = *0.35mm*
-bridge_flow_ratio = 0.95
-bridge_speed = 30
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4
-first_layer_extrusion_width = 0.42
-perimeter_extrusion_width = 0.43
-solid_infill_extrusion_width = 0.7
-top_infill_extrusion_width = 0.45
-support_material_extrusion_width = 0.37
-support_material_contact_distance = 0.1
-raft_contact_distance = 0.2
-top_solid_infill_speed = 40
-thick_bridges = 1
-overhangs = 0
-
-## MMU1 specific
-[print:0.15mm OPTIMAL SOLUBLE FULL]
-inherits = *0.15mm*; *soluble_support*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4 and num_extruders>1
-external_perimeter_speed = 25
-notes = Set your soluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
-perimeter_speed = 40
-solid_infill_speed = 40
-top_infill_extrusion_width = 0.45
-top_solid_infill_speed = 30
-bridge_flow_ratio = 0.8
-bridge_speed = 30
-
-[print:0.15mm OPTIMAL SOLUBLE INTERFACE]
-inherits = 0.15mm OPTIMAL SOLUBLE FULL
-notes = Set your soluble extruder in Multiple Extruders >  Support material/raft interface extruder
-support_material_extruder = 0
-support_material_interface_layers = 3
-support_material_with_sheath = 0
-support_material_xy_spacing = 80%
-
-[print:0.20mm NORMAL SOLUBLE FULL]
-inherits = *0.20mm*; *soluble_support*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4 and num_extruders>1
-external_perimeter_speed = 30
-notes = Set your soluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
-perimeter_speed = 40
-solid_infill_speed = 40
-top_solid_infill_speed = 30
-bridge_flow_ratio = 0.95
-bridge_speed = 30
-
-[print:0.20mm NORMAL SOLUBLE INTERFACE]
-inherits = 0.20mm NORMAL SOLUBLE FULL
-notes = Set your soluble extruder in Multiple Extruders >  Support material/raft interface extruder
-support_material_extruder = 0
-support_material_interface_layers = 3
-support_material_with_sheath = 0
-support_material_xy_spacing = 80%
-
-## MK2 - 0.25mm nozzle
-
-[print:0.05mm ULTRADETAIL @0.25 nozzle]
-inherits = *0.05mm*; *0.25nozzle*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25 and num_extruders==1
-fill_density = 20%
-infill_speed = 20
-max_print_speed = 100
-perimeter_speed = 20
-small_perimeter_speed = 15
-solid_infill_speed = 20
-support_material_speed = 20
-support_material_contact_distance = 0.07
-raft_contact_distance = 0.07
-
-[print:0.10mm DETAIL @0.25 nozzle]
-inherits = *0.10mm*; *0.25nozzle*
-bridge_acceleration = 600
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25
-external_perimeter_speed = 20
-infill_acceleration = 1000
-infill_speed = 40
-perimeter_acceleration = 600
-perimeter_speed = 25
-small_perimeter_speed = 15
-solid_infill_speed = 40
-top_solid_infill_speed = 30
-support_material_contact_distance = 0.07
-raft_contact_distance = 0.07
-single_extruder_multi_material_priming = 0
-
-[print:0.15mm OPTIMAL @0.25 nozzle]
-inherits = *0.15mm*; *0.25nozzle*
-bridge_acceleration = 600
-bridge_flow_ratio = 0.8
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25
-external_perimeter_speed = 20
-infill_acceleration = 1000
-infill_speed = 40
-perimeter_acceleration = 600
-perimeter_speed = 25
-small_perimeter_speed = 15
-solid_infill_speed = 40
-top_solid_infill_speed = 30
-support_material_contact_distance = 0.08
-raft_contact_distance = 0.07
-perimeter_extrusion_width = 0.27
-external_perimeter_extrusion_width = 0.27
-infill_extrusion_width = 0.27
-solid_infill_extrusion_width = 0.27
-single_extruder_multi_material_priming = 0
-
-[print:0.15mm SOLUBLE FULL @0.25 nozzle]
-inherits = 0.15mm OPTIMAL @0.25 nozzle
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25 and num_extruders>1
-support_material_contact_distance = 0
-raft_contact_distance = 0
-wipe_tower_bridging = 5
-solid_infill_speed = 40
-support_material_extruder = 5
-support_material_interface_extruder = 5
-support_material_with_sheath = 1
-support_material_interface_layers = 4
-support_material_threshold = 60
-support_material = 1
-support_material_synchronize_layers = 1
-support_material_xy_spacing = 100%
-support_material_style = snug
-raft_first_layer_expansion = 2
-support_material_interface_spacing = 0.05
-single_extruder_multi_material_priming = 0
-
-[print:0.15mm SOLUBLE INTERFACE @0.25 nozzle]
-inherits = 0.15mm SOLUBLE FULL @0.25 nozzle
-support_material_extruder = 0
-support_material_interface_extruder = 5
-support_material_with_sheath = 0
-support_material_style = grid
-
-## MK2 - 0.6mm nozzle
-
-[print:0.15mm OPTIMAL @0.6 nozzle]
-inherits = *0.15mm*; *0.6nozzle*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6
-
-[print:0.20mm NORMAL @0.6 nozzle]
-inherits = *0.20mm*; *0.6nozzle*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6
-
-[print:0.35mm FAST @0.6 nozzle]
-inherits = *0.35mm*; *0.6nozzle*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6
-
-## MMU1 specific
-[print:0.35mm FAST sol full @0.6 nozzle]
-inherits = *0.35mm*; *0.6nozzle*; *soluble_support*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_model=="MK2SMM" and nozzle_diameter[0]==0.6 and num_extruders>1
-external_perimeter_extrusion_width = 0.6
-external_perimeter_speed = 30
-notes = Set your soluble extruder in Multiple Extruders > Support material/raft interface extruder
-perimeter_speed = 40
-support_material_speed = 40
-support_material_interface_layers = 2
-support_material_xy_spacing = 120%
-top_infill_extrusion_width = 0.6
-support_material_extrusion_width = 0.6
-
-[print:0.35mm FAST sol int @0.6 nozzle]
-inherits = 0.35mm FAST sol full @0.6 nozzle
-support_material_extruder = 0
-support_material_interface_layers = 3
-support_material_with_sheath = 0
-support_material_xy_spacing = 150%
-
-## MK2.5
-
-[print:0.10mm DETAIL @MK2.5]
-inherits = 0.10mm DETAIL
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
-single_extruder_multi_material_priming = 0
-
-[print:0.15mm 100mms Linear Advance @MK2.5]
-inherits = 0.15mm 100mms Linear Advance
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4
-single_extruder_multi_material_priming = 0
-
-[print:0.15mm OPTIMAL @MK2.5]
-inherits = 0.15mm OPTIMAL
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4
-single_extruder_multi_material_priming = 0
-
-[print:0.20mm 100mms Linear Advance @MK2.5]
-inherits = 0.20mm 100mms Linear Advance
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4
-single_extruder_multi_material_priming = 0
-
-[print:0.20mm NORMAL @MK2.5]
-inherits = 0.20mm NORMAL
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4
-single_extruder_multi_material_priming = 0
-
-[print:0.35mm FAST @MK2.5]
-inherits = 0.35mm FAST
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4
-single_extruder_multi_material_priming = 0
-overhangs = 0
-
-## MK2.5 - MMU2 specific
-
-[print:0.15mm OPTIMAL SOLUBLE FULL @MK2.5]
-inherits = 0.15mm OPTIMAL SOLUBLE FULL
-support_material_extruder = 5
-support_material_interface_extruder = 5
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
-
-[print:0.15mm OPTIMAL SOLUBLE INTERFACE @MK2.5]
-inherits = 0.15mm OPTIMAL SOLUBLE INTERFACE
-support_material_extruder = 0
-support_material_interface_extruder = 5
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
-
-[print:0.20mm NORMAL SOLUBLE FULL @MK2.5]
-inherits = 0.20mm NORMAL SOLUBLE FULL
-support_material_extruder = 5
-support_material_interface_extruder = 5
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
-single_extruder_multi_material_priming = 0
-
-[print:0.20mm NORMAL SOLUBLE INTERFACE @MK2.5]
-inherits = 0.20mm NORMAL SOLUBLE INTERFACE
-support_material_extruder = 0
-support_material_interface_extruder = 5
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
-single_extruder_multi_material_priming = 0
-
-# MK2.5 MMU2 0.6 nozzle
-[print:0.35mm SOLUBLE FULL @0.6 nozzle MK2.5]
-inherits = *0.35mm*; *0.6nozzle*; *soluble_support*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and printer_model!="MK2SMM" and nozzle_diameter[0]==0.6 and num_extruders>1
-external_perimeter_extrusion_width = 0.6
-external_perimeter_speed = 30
-notes = Set your soluble extruder in Multiple Extruders > Support material/raft interface extruder
-perimeter_speed = 40
-support_material_speed = 40
-support_material_interface_layers = 2
-support_material_xy_spacing = 80%
-support_material_extruder = 5
-support_material_interface_extruder = 5
-top_infill_extrusion_width = 0.6
-support_material_extrusion_width = 0.6
-
-[print:0.35mm SOLUBLE INTERFACE @0.6 nozzle MK2.5]
-inherits = 0.35mm SOLUBLE FULL @0.6 nozzle MK2.5
-support_material_extruder = 0
-support_material_interface_layers = 3
-support_material_with_sheath = 0
-support_material_xy_spacing = 80%
-
-## MK3 family ##
-
-## MK3 - 0.4mm nozzle
-
-[print:0.05mm ULTRADETAIL @MK3]
-inherits = *0.05mm*; *MK3*
-fill_pattern = gyroid
-fill_density = 15%
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/  and nozzle_diameter[0]==0.4 and ! single_extruder_multi_material
-top_infill_extrusion_width = 0.4
-
-[print:0.07mm ULTRADETAIL @MK3]
-inherits = *0.07mm*; *MK3*
-fill_pattern = gyroid
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/  and nozzle_diameter[0]==0.4 and ! single_extruder_multi_material
-top_infill_extrusion_width = 0.4
-
-[print:0.10mm DETAIL @MK3]
-inherits = *0.10mm*; *MK3*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4
-external_perimeter_speed = 25
-infill_acceleration = 1000
-bridge_acceleration = 800
-infill_speed = 80
-max_print_speed = 200
-perimeter_speed = 45
-solid_infill_speed = 80
-top_infill_extrusion_width = 0.4
-top_solid_infill_speed = 40
-fill_pattern = gyroid
-fill_density = 15%
-perimeters = 3
-wipe_tower_bridging = 5
-
-[print:0.15mm QUALITY @MK3]
-inherits = *0.15mm*; *MK3*
-bridge_speed = 25
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4
-external_perimeter_speed = 25
-infill_acceleration = 1000
-infill_speed = 80
-max_print_speed = 200
-perimeter_speed = 45
-solid_infill_speed = 80
-top_solid_infill_speed = 40
-fill_pattern = gyroid
-fill_density = 15%
-
-[print:0.15mm SPEED @MK3]
-inherits = *0.15mm*; *MK3*
-bridge_speed = 25
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4
-external_perimeter_speed = 35
-infill_acceleration = 1000
-infill_speed = 200
-max_print_speed = 200
-perimeter_speed = 60
-solid_infill_speed = 200
-top_solid_infill_speed = 50
-
-[print:0.20mm QUALITY @MK3]
-inherits = *0.20mm*; *MK3*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4
-external_perimeter_speed = 25
-infill_acceleration = 1000
-infill_speed = 80
-max_print_speed = 200
-perimeter_speed = 45
-solid_infill_speed = 80
-top_solid_infill_speed = 40
-fill_pattern = gyroid
-fill_density = 15%
-
-[print:0.20mm SPEED @MK3]
-inherits = *0.20mm*; *MK3*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4
-external_perimeter_speed = 35
-infill_acceleration = 1000
-infill_speed = 200
-max_print_speed = 200
-perimeter_speed = 60
-solid_infill_speed = 200
-top_solid_infill_speed = 50
-
-[print:0.30mm DRAFT @MK3]
-inherits = *0.30mm*; *MK3*
-bottom_solid_layers = 3
-bridge_speed = 25
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4
-external_perimeter_speed = 35
-infill_acceleration = 1000
-infill_speed = 85
-max_print_speed = 200
-perimeter_speed = 50
-small_perimeter_speed = 30
-solid_infill_speed = 80
-top_solid_infill_speed = 40
-support_material_speed = 45
-external_perimeter_extrusion_width = 0.6
-extrusion_width = 0.5
-first_layer_extrusion_width = 0.42
-infill_extrusion_width = 0.5
-perimeter_extrusion_width = 0.5
-solid_infill_extrusion_width = 0.5
-top_infill_extrusion_width = 0.45
-support_material_extrusion_width = 0.38
-support_material_contact_distance = 0.2
-raft_contact_distance = 0.2
-
-## MK3 - MMU2 specific
-[print:0.15mm SOLUBLE FULL @MK3]
-inherits = 0.15mm SPEED @MK3; *soluble_support*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
-notes = Set your soluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
-support_material_extruder = 5
-support_material_interface_extruder = 5
-perimeter_speed = 40
-solid_infill_speed = 40
-infill_speed = 80
-top_infill_extrusion_width = 0.45
-top_solid_infill_speed = 30
-support_material_speed = 45
-bridge_flow_ratio = 0.8
-bridge_speed = 30
-
-[print:0.15mm SOLUBLE INTERFACE @MK3]
-inherits = 0.15mm SOLUBLE FULL @MK3
-notes = Set your soluble extruder in Multiple Extruders >  Support material/raft interface extruder
-support_material_extruder = 0
-support_material_interface_layers = 3
-support_material_with_sheath = 0
-
-[print:0.20mm SOLUBLE FULL @MK3]
-inherits = 0.20mm SPEED @MK3; *soluble_support*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
-notes = Set your soluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
-support_material_extruder = 5
-support_material_interface_extruder = 5
-perimeter_speed = 40
-solid_infill_speed = 40
-infill_speed = 80
-top_infill_extrusion_width = 0.45
-top_solid_infill_speed = 30
-support_material_speed = 45
-bridge_flow_ratio = 0.95
-bridge_speed = 30
-
-[print:0.20mm SOLUBLE INTERFACE @MK3]
-inherits = 0.20mm SOLUBLE FULL @MK3
-notes = Set your soluble extruder in Multiple Extruders >  Support material/raft interface extruder
-support_material_extruder = 0
-support_material_interface_layers = 3
-support_material_with_sheath = 0
-
-## MK3 - 0.25mm nozzle
-
-[print:0.05mm ULTRADETAIL @0.25 nozzle MK3]
-inherits = *0.05mm*; *0.25nozzle*; *MK3*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.25 and num_extruders==1
-fill_pattern = grid
-fill_density = 20%
-support_material_contact_distance = 0.07
-raft_contact_distance = 0.07
-
-[print:0.07mm ULTRADETAIL @0.25 nozzle MK3]
-inherits = *0.07mm*; *0.25nozzle*; *MK3*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.25
-infill_speed = 30
-solid_infill_speed = 30
-support_material_speed = 30
-top_solid_infill_speed = 20
-fill_pattern = grid
-fill_density = 20%
-support_material_contact_distance = 0.07
-raft_contact_distance = 0.07
-
-[print:0.10mm DETAIL @0.25 nozzle MK3]
-inherits = *0.10mm*; *0.25nozzleMK3*; *MK3*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.25
-fill_pattern = grid
-fill_density = 20%
-support_material_contact_distance = 0.07
-raft_contact_distance = 0.07
-
-[print:0.15mm QUALITY @0.25 nozzle MK3]
-inherits = *0.15mm*; *0.25nozzleMK3*; *MK3*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.25
-fill_pattern = grid
-fill_density = 20%
-support_material_contact_distance = 0.08
-raft_contact_distance = 0.07
-perimeter_extrusion_width = 0.27
-external_perimeter_extrusion_width = 0.27
-infill_extrusion_width = 0.27
-solid_infill_extrusion_width = 0.27
-
-[print:0.15mm SOLUBLE FULL @0.25 nozzle MK3]
-inherits = 0.15mm QUALITY @0.25 nozzle MK3
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.25 and num_extruders>1
-support_material_contact_distance = 0
-raft_contact_distance = 0
-wipe_tower_bridging = 5
-solid_infill_speed = 40
-support_material_extruder = 5
-support_material_interface_extruder = 5
-support_material_with_sheath = 1
-support_material_interface_layers = 4
-support_material_threshold = 60
-support_material = 1
-support_material_synchronize_layers = 1
-support_material_xy_spacing = 100%
-support_material_style = snug
-raft_first_layer_expansion = 2
-support_material_interface_spacing = 0.05
-
-[print:0.15mm SOLUBLE INTERFACE @0.25 nozzle MK3]
-inherits = 0.15mm SOLUBLE FULL @0.25 nozzle MK3
-support_material_extruder = 0
-support_material_interface_extruder = 5
-support_material_with_sheath = 0
-support_material_style = grid
-
-## MK3 - 0.6mm nozzle
-
-[print:0.15mm DETAIL @0.6 nozzle MK3]
-inherits = *0.15mm*; *0.6nozzleMK3*; *MK306*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.6
-external_perimeter_speed = 35
-infill_acceleration = 1000
-infill_speed = 70
-max_print_speed = 100
-perimeter_speed = 45
-solid_infill_speed = 70
-top_solid_infill_speed = 45
-support_material_contact_distance = 0.22
-raft_contact_distance = 0.2
-bridge_flow_ratio = 1
-
-[print:0.20mm DETAIL @0.6 nozzle MK3]
-inherits = *0.20mm*; *0.6nozzleMK3*; *MK306*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.6
-external_perimeter_speed = 35
-infill_acceleration = 1000
-infill_speed = 70
-max_print_speed = 100
-perimeter_speed = 45
-solid_infill_speed = 70
-top_solid_infill_speed = 45
-support_material_contact_distance = 0.22
-raft_contact_distance = 0.2
-bridge_flow_ratio = 1
-
-[print:0.30mm QUALITY @0.6 nozzle MK3]
-inherits = *0.30mm*; *0.6nozzleMK3*; *MK306*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.6
-external_perimeter_speed = 35
-infill_acceleration = 1000
-infill_speed = 70
-max_print_speed = 100
-perimeter_speed = 45
-solid_infill_speed = 70
-top_solid_infill_speed = 45
-support_material_contact_distance = 0.25
-raft_contact_distance = 0.25
-bridge_flow_ratio = 1
-
-[print:0.35mm SPEED @0.6 nozzle MK3]
-inherits = *0.35mm*; *0.6nozzleMK3*; *MK306*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.6
-external_perimeter_speed = 35
-infill_acceleration = 1000
-infill_speed = 70
-max_print_speed = 100
-perimeter_speed = 45
-solid_infill_speed = 70
-top_solid_infill_speed = 45
-external_perimeter_extrusion_width = 0.68
-perimeter_extrusion_width = 0.68
-infill_extrusion_width = 0.68
-solid_infill_extrusion_width = 0.68
-support_material_contact_distance = 0.25
-raft_contact_distance = 0.25
-bridge_flow_ratio = 0.95
-
-[print:0.40mm DRAFT @0.6 nozzle MK3]
-inherits = *0.40mm*; *0.6nozzleMK3*; *MK306*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.6
-external_perimeter_speed = 35
-infill_acceleration = 1000
-infill_speed = 70
-max_print_speed = 100
-perimeter_speed = 45
-solid_infill_speed = 70
-top_solid_infill_speed = 45
-external_perimeter_extrusion_width = 0.68
-perimeter_extrusion_width = 0.68
-infill_extrusion_width = 0.68
-solid_infill_extrusion_width = 0.68
-support_material_contact_distance = 0.25
-raft_contact_distance = 0.25
-bridge_flow_ratio = 0.95
-
-## MK3 - MMU2 specific
-
-[print:0.30mm SOLUBLE FULL @0.6 nozzle MK3]
-inherits = 0.30mm QUALITY @0.6 nozzle MK3; *soluble_support*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.6 and num_extruders>1
-notes = Set your soluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
-support_material_extruder = 5
-support_material_interface_extruder = 5
-support_material_speed = 40
-perimeter_speed = 40
-solid_infill_speed = 40
-top_infill_extrusion_width = 0.6
-support_material_extrusion_width = 0.6
-top_solid_infill_speed = 30
-support_material_xy_spacing = 80%
-
-[print:0.30mm SOLUBLE INTERFACE @0.6 nozzle MK3]
-inherits = 0.30mm SOLUBLE FULL @0.6 nozzle MK3
-notes = Set your soluble extruder in Multiple Extruders >  Support material/raft interface extruder
-support_material_extruder = 0
-support_material_interface_layers = 3
-support_material_with_sheath = 0
-
-## 0.8mm nozzle - MK2.5 and MK3
-## Only for MMU2 Single mode at the moment
-
-[print:0.30mm DETAIL @0.8 nozzle]
-inherits = *common*; *0.8nozzle*
-layer_height = 0.30
-compatible_printers_condition = printer_model=~/(MK3|MK2.5).*/ and nozzle_diameter[0]==0.8 and num_extruders==1
-perimeter_speed = 35
-external_perimeter_speed = 25
-infill_acceleration = 1000
-infill_speed = 50
-max_print_speed = 80
-solid_infill_speed = 50
-top_solid_infill_speed = 35
-support_material_speed = 40
-
-[print:0.40mm QUALITY @0.8 nozzle]
-inherits = *common*; *0.8nozzle*
-layer_height = 0.4
-compatible_printers_condition = printer_model=~/(MK3|MK2.5).*/ and nozzle_diameter[0]==0.8 and num_extruders==1
-perimeter_speed = 35
-external_perimeter_speed = 25
-infill_acceleration = 1000
-infill_speed = 50
-max_print_speed = 50
-solid_infill_speed = 45
-top_solid_infill_speed = 35
-support_material_speed = 40
-
-[print:0.55mm DRAFT @0.8 nozzle]
-inherits = *common*; *0.8nozzle*
-layer_height = 0.55
-compatible_printers_condition = printer_model=~/(MK3|MK2.5).*/ and nozzle_diameter[0]==0.8 and num_extruders==1
-perimeter_speed = 30
-external_perimeter_speed = 25
-infill_acceleration = 1000
-infill_speed = 50
-max_print_speed = 50
-solid_infill_speed = 40
-support_material_speed = 35
-support_material_contact_distance = 0.25
-top_solid_infill_speed = 30
-external_perimeter_extrusion_width = 1
-perimeter_extrusion_width = 1
-
-## MINI ##
-
-# MINI - 0.4mm nozzle
-
-[print:0.05mm ULTRADETAIL @MINI]
-inherits = *0.05mm*; *MINI*
-fill_pattern = gyroid
-fill_density = 15%
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/  and nozzle_diameter[0]==0.4
-top_infill_extrusion_width = 0.4
-small_perimeter_speed = 15
-perimeter_extrusion_width = 0.4
-external_perimeter_extrusion_width = 0.4
-support_material_xy_spacing = 60%
-support_material_speed = 30
-support_material_extrusion_width = 0.35
-bridge_acceleration = 300
-
-[print:0.07mm ULTRADETAIL @MINI]
-inherits = *0.07mm*; *MINI*
-fill_pattern = gyroid
-fill_density = 15%
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/  and nozzle_diameter[0]==0.4
-top_infill_extrusion_width = 0.4
-small_perimeter_speed = 15
-perimeter_extrusion_width = 0.4
-external_perimeter_extrusion_width = 0.4
-support_material_xy_spacing = 60%
-support_material_extrusion_width = 0.35
-bridge_acceleration = 300
-
-[print:0.10mm DETAIL @MINI]
-inherits = *0.10mm*; *MINI*
-bridge_speed = 20
-bridge_acceleration = 700
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.4
-perimeter_speed = 40
-external_perimeter_speed = 30
-infill_speed = 80
-solid_infill_speed = 80
-top_infill_extrusion_width = 0.4
-top_solid_infill_speed = 40
-fill_pattern = gyroid
-fill_density = 15%
-perimeters = 3
-support_material_xy_spacing = 60%
-
-[print:0.15mm QUALITY @MINI]
-inherits = *0.15mm*; *MINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.4
-perimeter_speed = 40
-external_perimeter_speed = 30
-infill_speed = 80
-solid_infill_speed = 80
-top_solid_infill_speed = 40
-fill_pattern = gyroid
-fill_density = 15%
-support_material_xy_spacing = 60%
-
-[print:0.15mm SPEED @MINI]
-inherits = *0.15mm*; *MINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.4
-perimeter_speed = 50
-external_perimeter_speed = 40
-infill_speed = 140
-solid_infill_speed = 140
-top_solid_infill_speed = 40
-support_material_xy_spacing = 60%
-
-[print:0.20mm QUALITY @MINI]
-inherits = *0.20mm*; *MINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.4
-perimeter_speed = 40
-external_perimeter_speed = 30
-infill_speed = 80
-solid_infill_speed = 80
-top_solid_infill_speed = 40
-fill_pattern = gyroid
-fill_density = 15%
-support_material_xy_spacing = 60%
-
-[print:0.20mm SPEED @MINI]
-inherits = *0.20mm*; *MINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.4
-perimeter_speed = 50
-external_perimeter_speed = 40
-infill_speed = 140
-max_print_speed = 150
-solid_infill_speed = 140
-top_solid_infill_speed = 40
-support_material_xy_spacing = 60%
-
-[print:0.25mm DRAFT @MINI]
-inherits = *0.25mm*; *MINI*
-bridge_speed = 25
-bridge_flow_ratio = 0.95
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.4
-external_perimeter_speed = 40
-infill_speed = 110
-perimeter_speed = 55
-small_perimeter_speed = 25
-solid_infill_speed = 100
-top_solid_infill_speed = 45
-first_layer_extrusion_width = 0.42
-infill_extrusion_width = 0.45
-solid_infill_extrusion_width = 0.45
-top_infill_extrusion_width = 0.4
-support_material_xy_spacing = 60%
-support_material_contact_distance = 0.2
-raft_contact_distance = 0.2
-
-# MINI - 0.25mm nozzle
-
-[print:0.05mm ULTRADETAIL @0.25 nozzle MINI]
-inherits = *0.05mm*; *0.25nozzle*; *MINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.25
-fill_pattern = grid
-fill_density = 20%
-support_material_speed = 30
-support_material_contact_distance = 0.07
-raft_contact_distance = 0.07
-
-[print:0.07mm ULTRADETAIL @0.25 nozzle MINI]
-inherits = *0.07mm*; *0.25nozzle*; *MINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.25
-infill_speed = 30
-solid_infill_speed = 30
-support_material_speed = 30
-top_solid_infill_speed = 20
-fill_pattern = grid
-fill_density = 20%
-support_material_contact_distance = 0.07
-raft_contact_distance = 0.07
-
-[print:0.10mm DETAIL @0.25 nozzle MINI]
-inherits = *0.10mm*; *0.25nozzleMINI*; *MINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.25
-fill_pattern = grid
-fill_density = 20%
-support_material_contact_distance = 0.07
-raft_contact_distance = 0.07
-
-[print:0.15mm QUALITY @0.25 nozzle MINI]
-inherits = *0.15mm*; *0.25nozzleMINI*; *MINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.25
-fill_pattern = grid
-fill_density = 20%
-support_material_contact_distance = 0.08
-raft_contact_distance = 0.07
-perimeter_extrusion_width = 0.27
-external_perimeter_extrusion_width = 0.27
-infill_extrusion_width = 0.27
-solid_infill_extrusion_width = 0.27
-
-# MINI - 0.6mm nozzle
-
-[print:0.15mm DETAIL @0.6 nozzle MINI]
-inherits = *0.15mm*; *0.6nozzleMINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6
-external_perimeter_speed = 35
-infill_speed = 70
-max_print_speed = 100
-perimeter_speed = 45
-solid_infill_speed = 70
-top_solid_infill_speed = 45
-infill_extrusion_width = 0.65
-solid_infill_extrusion_width = 0.65
-support_material_contact_distance = 0.22
-raft_contact_distance = 0.22
-bridge_flow_ratio = 1
-
-[print:0.20mm DETAIL @0.6 nozzle MINI]
-inherits = *0.20mm*; *0.6nozzleMINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6
-external_perimeter_speed = 35
-infill_speed = 70
-max_print_speed = 100
-perimeter_speed = 45
-solid_infill_speed = 70
-top_solid_infill_speed = 45
-infill_extrusion_width = 0.65
-solid_infill_extrusion_width = 0.65
-support_material_contact_distance = 0.22
-raft_contact_distance = 0.22
-bridge_flow_ratio = 1
-
-[print:0.30mm QUALITY @0.6 nozzle MINI]
-inherits = *0.30mm*; *0.6nozzleMINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6
-external_perimeter_speed = 35
-infill_speed = 65
-max_print_speed = 100
-perimeter_speed = 45
-solid_infill_speed = 65
-top_solid_infill_speed = 45
-external_perimeter_extrusion_width = 0.68
-perimeter_extrusion_width = 0.68
-support_material_contact_distance = 0.25
-raft_contact_distance = 0.25
-bridge_flow_ratio = 1
-
-[print:0.35mm SPEED @0.6 nozzle MINI]
-inherits = *0.35mm*; *0.6nozzleMINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6
-external_perimeter_speed = 35
-infill_speed = 60
-max_print_speed = 100
-perimeter_speed = 45
-solid_infill_speed = 60
-top_solid_infill_speed = 45
-external_perimeter_extrusion_width = 0.68
-perimeter_extrusion_width = 0.68
-support_material_contact_distance = 0.25
-raft_contact_distance = 0.25
-bridge_flow_ratio = 0.95
-
-[print:0.40mm DRAFT @0.6 nozzle MINI]
-inherits = *0.40mm*; *0.6nozzleMINI*
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6
-external_perimeter_speed = 35
-infill_speed = 50
-max_print_speed = 100
-perimeter_speed = 45
-solid_infill_speed = 50
-top_solid_infill_speed = 45
-external_perimeter_extrusion_width = 0.68
-perimeter_extrusion_width = 0.68
-infill_extrusion_width = 0.68
-solid_infill_extrusion_width = 0.68
-support_material_contact_distance = 0.25
-raft_contact_distance = 0.25
-bridge_flow_ratio = 0.95
-
-# MINI - 0.8mm nozzle
-
-[print:0.30mm DETAIL @0.8 nozzle MINI]
-inherits = 0.30mm DETAIL @0.8 nozzle
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]==0.8
-perimeter_speed = 35
-external_perimeter_speed = 25
-infill_acceleration = 1000
-infill_speed = 50
-max_print_speed = 80
-solid_infill_speed = 45
-top_solid_infill_speed = 35
-support_material_speed = 40
-travel_speed = 150
-
-[print:0.40mm QUALITY @0.8 nozzle MINI]
-inherits = 0.40mm QUALITY @0.8 nozzle
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]==0.8
-infill_speed = 40
-max_print_speed = 50
-solid_infill_speed = 40
-top_solid_infill_speed = 30
-support_material_speed = 40
-travel_speed = 150
-
-[print:0.55mm DRAFT @0.8 nozzle MINI]
-inherits = 0.55mm DRAFT @0.8 nozzle
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]==0.8
-infill_acceleration = 1000
-infill_speed = 40
-solid_infill_speed = 40
-support_material_speed = 35
-support_material_contact_distance = 0.25
-raft_contact_distance = 0.2
-top_solid_infill_speed = 28
-external_perimeter_extrusion_width = 1
-perimeter_extrusion_width = 1
-travel_speed = 150
-
-# XXXXXXxxXXXXXXXXXXXXXX
-# XXX--- filament ---XXX
-# XXXXXXXXxxXXXXXXXXXXXX
-
-[filament:*common*]
-cooling = 1
-compatible_printers = 
-# For now, all but selected filaments are disabled for the MMU 2.0
-compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-end_filament_gcode = "; Filament-specific end gcode"
-extrusion_multiplier = 1
-filament_loading_speed = 28
-filament_loading_speed_start = 3
-filament_unloading_speed = 90
-filament_unloading_speed_start = 100
-filament_toolchange_delay = 0
-filament_cooling_moves = 4
-filament_cooling_initial_speed = 2.2
-filament_cooling_final_speed = 3.4
-filament_load_time = 0
-filament_unload_time = 0
-filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-filament_minimal_purge_on_wipe_tower = 15
-filament_cost = 0
-filament_density = 0
-filament_diameter = 1.75
-filament_notes = ""
-filament_settings_id = ""
-filament_soluble = 0
-min_print_speed = 15
-slowdown_below_layer_time = 15
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif} ; Filament gcode"
-
-[filament:*PLA*]
-inherits = *common*
-bed_temperature = 60
-bridge_fan_speed = 100
-disable_fan_first_layers = 1
-full_fan_speed_layer = 4
-fan_always_on = 1
-fan_below_layer_time = 100
-filament_colour = #FF8000
-filament_max_volumetric_speed = 15
-filament_type = PLA
-first_layer_bed_temperature = 60
-first_layer_temperature = 215
-max_fan_speed = 100
-min_fan_speed = 100
-temperature = 210
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0"
-
-[filament:*PET*]
-inherits = *common*
-bed_temperature = 90
-bridge_fan_speed = 50
-disable_fan_first_layers = 3
-full_fan_speed_layer = 5
-fan_always_on = 1
-fan_below_layer_time = 20
-filament_colour = #FF8000
-filament_max_volumetric_speed = 8
-filament_type = PETG
-first_layer_bed_temperature = 85
-first_layer_temperature = 230
-max_fan_speed = 50
-min_fan_speed = 30
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.08{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
-temperature = 240
-filament_retract_length = 1
-filament_retract_lift = 0.2
-compatible_printers_condition = printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:*PET06*]
-inherits = *PET*
-compatible_printers_condition = nozzle_diameter[0]==0.6 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-filament_max_volumetric_speed = 15
-
-[filament:*PETMMU1*]
-# inherits = *PET*
-filament_retract_length = nil
-filament_retract_speed = nil
-filament_retract_lift = 0.2
-compatible_printers_condition = printer_model=="MK2SMM"
-
-[filament:*PETMINI*]
-full_fan_speed_layer = 0
-filament_retract_length = nil
-filament_retract_speed = 45
-filament_deretract_speed = 25
-filament_retract_lift = nil
-filament_retract_before_travel = 1
-filament_max_volumetric_speed = 7
-compatible_printers_condition = printer_model=="MINI"
-start_filament_gcode = "M900 K{if nozzle_diameter[0]==0.6}0.12{elsif nozzle_diameter[0]==0.8}0.06{else}0.2{endif} ; Filament gcode"
-
-[filament:*PETMINI06*]
-full_fan_speed_layer = 0
-filament_retract_length = nil
-filament_retract_speed = 45
-filament_deretract_speed = 25
-filament_retract_lift = nil
-filament_retract_before_travel = 1
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]==0.6
-start_filament_gcode = "M900 K0.12 ; Filament gcode"
-filament_max_volumetric_speed = 13
-
-[filament:*ABSMINI*]
-bed_temperature = 100
-first_layer_bed_temperature = 100
-filament_retract_length = 2.7
-filament_retract_speed = nil
-filament_deretract_speed = nil
-filament_retract_lift = nil
-filament_retract_before_travel = 3
-filament_wipe = 0
-filament_max_volumetric_speed = 10
-slowdown_below_layer_time = 20
-compatible_printers_condition = printer_model=="MINI"
-start_filament_gcode = "M900 K{if nozzle_diameter[0]==0.6}0.12{elsif nozzle_diameter[0]==0.8}0.06{else}0.2{endif} ; Filament gcode"
-
-[filament:*FLEXMINI*]
-inherits = *FLEX*
-first_layer_temperature = 245
-temperature = 245
-filament_retract_length = 4
-filament_retract_speed = 40
-filament_deretract_speed = 15
-filament_retract_lift = 0
-filament_retract_before_travel = 7
-filament_wipe = 0
-bridge_fan_speed = 80
-fan_always_on = 1
-cooling = 0
-max_fan_speed = 50
-min_fan_speed = 50
-filament_max_volumetric_speed = 1.35
-compatible_printers_condition = nozzle_diameter[0]>0.35 and printer_model=="MINI"
-disable_fan_first_layers = 4
-full_fan_speed_layer = 6
-extrusion_multiplier = 1.15
-filament_density = 1.22
-filament_colour = #F2F200
-start_filament_gcode = "M900 K0 ; Filament gcode"
-
-[filament:*ABS*]
-inherits = *common*
-bed_temperature = 110
-bridge_fan_speed = 25
-cooling = 0
-disable_fan_first_layers = 3
-fan_always_on = 0
-fan_below_layer_time = 20
-filament_colour = #FFF2EC
-filament_max_volumetric_speed = 11
-filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-filament_type = ABS
-first_layer_bed_temperature = 100
-first_layer_temperature = 255
-max_fan_speed = 30
-min_fan_speed = 20
-temperature = 255
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-compatible_printers_condition = printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:*ABSC*]
-inherits = *common*
-bed_temperature = 110
-bridge_fan_speed = 25
-cooling = 1
-disable_fan_first_layers = 4
-fan_always_on = 0
-fan_below_layer_time = 30
-slowdown_below_layer_time = 20
-filament_colour = #FFF2EC
-filament_max_volumetric_speed = 11
-filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-filament_type = ABS
-first_layer_bed_temperature = 100
-first_layer_temperature = 255
-max_fan_speed = 15
-min_fan_speed = 15
-min_print_speed = 15
-temperature = 255
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-compatible_printers_condition = printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:*FLEX*]
-inherits = *common*
-bed_temperature = 50
-bridge_fan_speed = 80
-# For now, all but selected filaments are disabled for the MMU 2.0
-compatible_printers_condition = nozzle_diameter[0]>0.35 and printer_model!="MK2SMM" and printer_model!="MINI" and num_extruders==1 && ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and single_extruder_multi_material)
-cooling = 0
-disable_fan_first_layers = 3
-extrusion_multiplier = 1.15
-fan_always_on = 0
-fan_below_layer_time = 100
-filament_colour = #008000
-filament_max_volumetric_speed = 1.5
-filament_type = FLEX
-first_layer_bed_temperature = 50
-first_layer_temperature = 240
-max_fan_speed = 90
-min_fan_speed = 70
-start_filament_gcode = "M900 K0"; Filament gcode"
-temperature = 240
-filament_retract_length = 0.8
-filament_deretract_speed = 25
-filament_retract_lift = 0
-filament_wipe = 0
-
-[filament:ColorFabb bronzeFill]
-inherits = *PLA*
-filament_vendor = ColorFabb
-compatible_printers_condition = nozzle_diameter[0]>0.35 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-extrusion_multiplier = 1.12
-filament_cost = 80.65
-filament_density = 3.9
-filament_spool_weight = 236
-filament_colour = #804040
-filament_max_volumetric_speed = 9
-
-[filament:ColorFabb steelFill]
-inherits = *PLA*
-filament_vendor = ColorFabb
-compatible_printers_condition = nozzle_diameter[0]>0.35 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-extrusion_multiplier = 1.15
-filament_cost = 80.65
-filament_density = 3.13
-filament_spool_weight = 236
-filament_colour = #808080
-filament_max_volumetric_speed = 8
-
-[filament:ColorFabb copperFill]
-inherits = *PLA*
-filament_vendor = ColorFabb
-compatible_printers_condition = nozzle_diameter[0]>0.35 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-extrusion_multiplier = 1.15
-filament_cost = 80.65
-filament_density = 3.9
-filament_spool_weight = 236
-filament_colour = #82603E
-filament_max_volumetric_speed = 9
-
-[filament:ColorFabb HT]
-inherits = *PET*
-filament_vendor = ColorFabb
-bed_temperature = 110
-bridge_fan_speed = 30
-cooling = 1
-disable_fan_first_layers = 3
-fan_always_on = 0
-fan_below_layer_time = 10
-filament_cost = 65.66
-filament_density = 1.18
-filament_spool_weight = 236
-first_layer_bed_temperature = 105
-first_layer_temperature = 270
-max_fan_speed = 20
-min_fan_speed = 10
-temperature = 270
-
-[filament:ColorFabb PLA-PHA]
-inherits = *PLA*
-filament_vendor = ColorFabb
-filament_cost = 54.84
-filament_density = 1.24
-filament_spool_weight = 236
-
-[filament:ColorFabb woodFill]
-inherits = *PLA*
-filament_vendor = ColorFabb
-compatible_printers_condition = nozzle_diameter[0]>0.35 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-extrusion_multiplier = 1.1
-filament_cost = 78.63
-filament_density = 1.15
-filament_spool_weight = 236
-filament_colour = #dfc287
-filament_max_volumetric_speed = 9
-first_layer_temperature = 200
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-temperature = 200
-filament_retract_lift = 0.2
-
-[filament:ColorFabb corkFill]
-inherits = *PLA*
-filament_vendor = ColorFabb
-compatible_printers_condition = nozzle_diameter[0]>0.35 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-extrusion_multiplier = 1.1
-filament_cost = 78.63
-filament_density = 1.18
-filament_spool_weight = 236
-filament_colour = #634d33
-filament_max_volumetric_speed = 6
-first_layer_temperature = 220
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-temperature = 220
-filament_retract_lift = 0.2
-
-[filament:ColorFabb XT]
-inherits = *PET*
-filament_vendor = ColorFabb
-filament_cost = 62.90
-filament_density = 1.27
-filament_spool_weight = 236
-first_layer_bed_temperature = 90
-first_layer_temperature = 260
-temperature = 270
-
-[filament:ColorFabb XT-CF20]
-inherits = *PET*
-filament_vendor = ColorFabb
-extrusion_multiplier = 1.05
-filament_cost = 80.65
-filament_density = 1.35
-filament_spool_weight = 236
-filament_colour = #804040
-filament_max_volumetric_speed = 2
-first_layer_bed_temperature = 90
-first_layer_temperature = 260
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.06{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0"
-temperature = 260
-filament_retract_length = nil
-filament_retract_lift = 0.4
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:ColorFabb nGen]
-inherits = *PET*
-filament_vendor = ColorFabb
-filament_cost = 52.46
-filament_density = 1.2
-filament_spool_weight = 236
-bridge_fan_speed = 40
-fan_always_on = 0
-fan_below_layer_time = 10
-filament_type = NGEN
-first_layer_temperature = 240
-max_fan_speed = 35
-min_fan_speed = 20
-
-[filament:ColorFabb nGen flex]
-inherits = *FLEX*
-filament_vendor = ColorFabb
-filament_cost = 58.30
-filament_density = 1
-filament_spool_weight = 236
-bed_temperature = 85
-bridge_fan_speed = 40
-cooling = 1
-disable_fan_first_layers = 3
-extrusion_multiplier = 1
-fan_below_layer_time = 10
-filament_max_volumetric_speed = 5
-first_layer_bed_temperature = 85
-first_layer_temperature = 260
-max_fan_speed = 35
-min_fan_speed = 20
-temperature = 260
-filament_retract_length = nil
-filament_retract_lift = 0
-compatible_printers_condition = nozzle_diameter[0]>0.35 and printer_model!="MINI" and num_extruders==1 && ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and single_extruder_multi_material)
-
-[filament:Kimya PETG Carbon]
-inherits = *PET*
-filament_vendor = Kimya
-extrusion_multiplier = 1.05
-filament_cost = 150.02
-filament_density = 1.317
-filament_colour = #804040
-filament_max_volumetric_speed = 6
-first_layer_bed_temperature = 85
-first_layer_temperature = 240
-temperature = 240
-filament_retract_length = nil
-filament_retract_lift = 0.3
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.06{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0"
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Kimya ABS Carbon]
-inherits = *ABSC*
-filament_vendor = Kimya
-filament_cost = 140.34
-filament_density = 1.032
-filament_colour = #804040
-filament_max_volumetric_speed = 6
-first_layer_temperature = 260
-temperature = 260
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Kimya ABS Kevlar]
-inherits = Kimya ABS Carbon
-filament_vendor = Kimya
-filament_density = 1.037
-
-[filament:E3D Edge]
-inherits = *PET*
-filament_vendor = E3D
-filament_cost = 56.9
-filament_density = 1.26
-filament_type = EDGE
-compatible_printers_condition = printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:E3D PC-ABS]
-inherits = *ABS*
-filament_vendor = E3D
-filament_cost = 0
-filament_type = PC
-filament_density = 1.05
-first_layer_temperature = 270
-temperature = 270
-
-[filament:Fillamentum PLA]
-inherits = *PLA*
-filament_vendor = Fillamentum
-filament_cost = 35.48
-filament_density = 1.24
-filament_spool_weight = 230
-
-[filament:Fillamentum ABS]
-inherits = *ABSC*
-filament_vendor = Fillamentum
-filament_cost = 32.4
-filament_density = 1.04
-filament_spool_weight = 230
-first_layer_temperature = 240
-temperature = 240
-
-[filament:Fillamentum ASA]
-inherits = *ABS*
-filament_vendor = Fillamentum
-filament_cost = 38.7
-filament_density = 1.07
-filament_spool_weight = 230
-fan_always_on = 1
-cooling = 1
-min_fan_speed = 20
-max_fan_speed = 20
-min_print_speed = 15
-slowdown_below_layer_time = 15
-first_layer_temperature = 260
-temperature = 260
-filament_type = ASA
-
-[filament:Prusament ASA]
-inherits = *ABS*
-filament_vendor = Prusa Polymers
-filament_cost = 42.69
-filament_density = 1.07
-filament_spool_weight = 201
-fan_always_on = 1
-first_layer_temperature = 260
-first_layer_bed_temperature = 105
-temperature = 260
-bed_temperature = 110
-cooling = 1
-min_fan_speed = 20
-max_fan_speed = 20
-bridge_fan_speed = 30
-min_print_speed = 15
-slowdown_below_layer_time = 15
-disable_fan_first_layers = 4
-filament_type = ASA
-filament_colour = #FFF2EC
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Prusament PC Blend]
-inherits = *ABS*
-filament_vendor = Prusa Polymers
-filament_cost = 62.36
-filament_density = 1.22
-filament_spool_weight = 201
-fan_always_on = 0
-first_layer_temperature = 275
-first_layer_bed_temperature = 110
-temperature = 275
-bed_temperature = 115
-cooling = 1
-min_fan_speed = 20
-max_fan_speed = 20
-bridge_fan_speed = 30
-min_print_speed = 15
-slowdown_below_layer_time = 20
-disable_fan_first_layers = 4
-fan_below_layer_time = 30
-filament_type = PC
-filament_colour = #DEE0E6
-filament_max_volumetric_speed = 8
-filament_retract_lift = 0.2
-compatible_printers_condition = printer_notes!~/.*PRINTER_MODEL_MK(2|2.5).*/ and nozzle_diameter[0]!=0.8 and printer_model!="MINI" and ! single_extruder_multi_material
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.07{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
-
-[filament:Prusament PC Blend @MK2]
-inherits = Prusament PC Blend
-first_layer_bed_temperature = 105
-bed_temperature = 110
-disable_fan_first_layers = 6
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and printer_notes=~/.*PRINTER_MODEL_MK(2|2.5).*/ and ! (printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and single_extruder_multi_material)
-
-[filament:Prusament PC Blend Carbon Fiber]
-inherits = Prusament PC Blend
-filament_cost = 90.73 
-filament_density = 1.16
-extrusion_multiplier = 1.04
-first_layer_temperature = 285
-temperature = 285
-disable_fan_first_layers = 4
-fan_below_layer_time = 10
-filament_colour = #BBBBBB
-filament_retract_length = nil
-filament_retract_lift = nil
-compatible_printers_condition = printer_notes!~/.*PRINTER_MODEL_MK(2|2.5).*/ and nozzle_diameter[0]>=0.4 and nozzle_diameter[0]!=0.8 and printer_model!="MINI" and ! single_extruder_multi_material
-
-[filament:Prusament PC Blend Carbon Fiber @MK2]
-inherits = Prusament PC Blend Carbon Fiber
-first_layer_bed_temperature = 105
-bed_temperature = 110
-disable_fan_first_layers = 6
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and nozzle_diameter[0]!=0.8 and printer_notes=~/.*PRINTER_MODEL_MK(2|2.5).*/ and ! (printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and single_extruder_multi_material)
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.07{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
-
-[filament:Prusament PA11 Carbon Fiber]
-inherits = Prusament PC Blend Carbon Fiber
-filament_cost = 151.24 
-filament_density = 1.11
-filament_type = PA
-filament_max_volumetric_speed = 6.5
-extrusion_multiplier = 1.05
-first_layer_temperature = 275
-temperature = 285
-first_layer_bed_temperature = 90
-bed_temperature = 115
-fan_below_layer_time = 10
-compatible_printers_condition = printer_notes!~/.*PRINTER_MODEL_MK(2|2.5).*/ and nozzle_diameter[0]>=0.4 and nozzle_diameter[0]!=0.8 and printer_model!="MINI" and ! single_extruder_multi_material
-
-[filament:Prusament PA11 Carbon Fiber @MK2]
-inherits = Prusament PA11 Carbon Fiber
-first_layer_bed_temperature = 90
-bed_temperature = 110
-disable_fan_first_layers = 6
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and nozzle_diameter[0]!=0.8 and printer_notes=~/.*PRINTER_MODEL_MK(2|2.5).*/ and ! (printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and single_extruder_multi_material)
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.07{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
-
-[filament:Fillamentum CPE]
-inherits = *PET*
-filament_vendor = Fillamentum
-filament_cost = 56.45
-filament_density = 1.25
-filament_spool_weight = 230
-filament_type = CPE
-first_layer_bed_temperature = 90
-first_layer_temperature = 275
-min_fan_speed = 30
-max_fan_speed = 50
-disable_fan_first_layers = 3
-full_fan_speed_layer = 5
-temperature = 275
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.08{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
-
-[filament:Fillamentum Timberfill]
-inherits = *PLA*
-filament_vendor = Fillamentum
-compatible_printers_condition = nozzle_diameter[0]>0.35 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-extrusion_multiplier = 1.1
-filament_cost = 68
-filament_density = 1.15
-filament_spool_weight = 230
-filament_colour = #804040
-filament_max_volumetric_speed = 10
-first_layer_temperature = 190
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-temperature = 190
-filament_retract_lift = 0.2
-
-[filament:Smartfil Wood]
-inherits = *PLA*
-filament_vendor = Smart Materials 3D
-compatible_printers_condition = nozzle_diameter[0]>0.35 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-extrusion_multiplier = 1.1
-filament_cost = 68
-filament_density = 1.58
-filament_colour = #804040
-filament_max_volumetric_speed = 9
-first_layer_temperature = 220
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-temperature = 220
-filament_retract_lift = 0.2
-
-[filament:Generic ABS]
-inherits = *ABSC*
-filament_vendor = Generic
-filament_cost = 27.82
-filament_density = 1.04
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Esun ABS]
-inherits = *ABSC*
-filament_vendor = Esun
-filament_cost = 27.82
-filament_density = 1.01
-filament_spool_weight = 265
-
-[filament:Hatchbox ABS]
-inherits = *ABSC*
-filament_vendor = Hatchbox
-filament_cost = 27.82
-filament_density = 1.04
-filament_spool_weight = 245
-
-[filament:Filament PM ABS]
-inherits = *ABSC*
-renamed_from = "Plasty Mladec ABS"
-filament_vendor = Filament PM
-filament_cost = 27.82
-filament_density = 1.08
-filament_spool_weight = 230
-
-[filament:Verbatim ABS]
-inherits = *ABSC*
-filament_vendor = Verbatim
-filament_cost = 25.87
-filament_density = 1.05
-filament_spool_weight = 235
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.03{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-
-[filament:Generic PETG]
-inherits = *PET*
-renamed_from = "Generic PET"
-filament_vendor = Generic
-filament_cost = 27.82
-filament_density = 1.27
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Extrudr DuraPro ASA]
-inherits = Fillamentum ASA
-filament_vendor = Extrudr
-bed_temperature = 90
-filament_cost = 34.64
-filament_density = 1.05
-filament_notes = "https://www.extrudr.com/en/products/catalogue/?material=120"
-first_layer_bed_temperature = 90
-first_layer_temperature = 220
-temperature = 220
-filament_max_volumetric_speed = 10
-compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-filament_spool_weight = 230
-
-[filament:Extrudr PETG]
-inherits = *PET*
-filament_vendor = Extrudr
-bed_temperature = 70
-filament_cost = 35.45
-filament_density = 1.29
-filament_notes = "https://www.extrudr.com/en/products/catalogue/?material=94"
-first_layer_bed_temperature = 70
-first_layer_temperature = 220
-temperature = 220
-slowdown_below_layer_time = 20
-filament_retract_length = nil
-filament_retract_lift = nil
-filament_spool_weight = 262
-full_fan_speed_layer = 0
-compatible_printers_condition = printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Extrudr PETG @MINI]
-inherits = Extrudr PETG; *PETMINI*
-filament_vendor = Extrudr
-
-[filament:Extrudr XPETG CF]
-inherits = Extrudr PETG
-filament_cost = 62.49
-filament_density = 1.29
-filament_notes = "https://www.extrudr.com/en/products/catalogue/?material=198"
-first_layer_temperature = 235
-temperature = 235
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-filament_spool_weight = 230
-
-[filament:Extrudr XPETG CF @MINI]
-inherits = Extrudr XPETG CF; *PETMINI*
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model=="MINI"
-
-[filament:Extrudr XPETG Matt]
-inherits = Extrudr PETG
-filament_cost = 29.99
-filament_density = 1.41
-filament_notes = "https://www.extrudr.com/en/products/catalogue/?material=199"
-first_layer_temperature = 230
-temperature = 230
-
-[filament:Extrudr XPETG Matt @MINI]
-inherits = Extrudr XPETG Matt; *PETMINI*
-
-[filament:Extrudr BioFusion]
-inherits = *PLA*
-filament_vendor = Extrudr
-disable_fan_first_layers = 3
-full_fan_speed_layer = 0
-filament_cost = 31.23
-filament_density = 1.25
-filament_notes = "https://www.extrudr.com/en/products/catalogue/?material=121"
-first_layer_temperature = 220
-temperature = 220
-max_fan_speed = 45
-min_fan_speed = 25
-slowdown_below_layer_time = 20
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.07{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K43{endif} ; Filament gcode LA 1.0"
-filament_spool_weight = 230
-
-[filament:Extrudr Flax]
-inherits = *PLA*
-filament_vendor = Extrudr
-filament_cost = 50.91
-filament_density = 1.45
-filament_notes = "High Performance Filament for decorative parts.\nPrints as easily as PLA with much higher strength and temperature resistance.\nFully biodegradable with a nice matt finish.\n\nhttps://www.extrudr.com/en/products/catalogue/?material=131"
-first_layer_temperature = 190
-temperature = 190
-max_fan_speed = 80
-min_fan_speed = 30
-full_fan_speed_layer = 0
-slowdown_below_layer_time = 20
-filament_max_volumetric_speed = 11
-filament_spool_weight = 262
-
-[filament:Extrudr GreenTEC]
-inherits = *PLA*
-filament_vendor = Extrudr
-filament_cost = 50.91
-filament_density = 1.3
-filament_notes = "https://www.extrudr.com/en/products/catalogue/?ignorechildren=1&material=106"
-first_layer_temperature = 208
-temperature = 208
-slowdown_below_layer_time = 20
-filament_spool_weight = 262
-
-[filament:Extrudr GreenTEC Pro]
-inherits = *PLA*
-filament_vendor = Extrudr
-filament_cost = 56.23
-filament_density = 1.35
-filament_notes = "High Performance Filament for technical parts.\nPrints as easily as PLA with much higher strength and temperature resistance.\nFully biodegradable with a nice matt finish.\n\nhttps://www.extrudr.com/en/products/catalogue/?material=134"
-temperature = 215
-max_fan_speed = 80
-min_fan_speed = 30
-full_fan_speed_layer = 0
-slowdown_below_layer_time = 20
-filament_spool_weight = 230
-
-[filament:Extrudr GreenTEC Pro Carbon]
-inherits = *PLA*
-filament_vendor = Extrudr
-filament_cost = 62.49
-filament_density = 1.2
-filament_notes = "High Performance Filament for technical parts.\nPrints as easily as PLA with much higher stregnth and temperature resistance.\nFully biodegradable with a nice matt finish.\n\nhttps://www.extrudr.com/en/products/catalogue/?material=138"
-first_layer_temperature = 225
-max_fan_speed = 80
-min_fan_speed = 30
-temperature = 225
-full_fan_speed_layer = 0
-slowdown_below_layer_time = 20
-filament_spool_weight = 230
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Extrudr PLA NX1]
-inherits = *PLA*
-filament_vendor = Extrudr
-filament_cost = 22.76
-filament_density = 1.24
-filament_notes = "https://www.extrudr.com/en/products/catalogue/?material=97"
-temperature = 205
-bed_temperature = 60
-first_layer_temperature = 205
-first_layer_bed_temperature = 60
-full_fan_speed_layer = 0
-max_fan_speed = 90
-min_fan_speed = 30
-slowdown_below_layer_time = 20
-filament_spool_weight = 262
-
-[filament:Extrudr PLA NX2]
-inherits = Extrudr PLA NX1
-filament_cost = 23.63
-filament_density = 1.3
-filament_notes = "https://www.extrudr.com/en/products/catalogue/?material=128"
-
-[filament:Extrudr Flex Hard]
-inherits = *FLEX*
-filament_vendor = Extrudr
-disable_fan_first_layers = 1
-extrusion_multiplier = 1.2
-filament_cost = 39.98
-filament_density = 1.2
-filament_deretract_speed = nil
-filament_max_volumetric_speed = 3
-filament_notes = "https://www.extrudr.com/en/products/catalogue/?material=115"
-filament_retract_length = 0.4
-filament_wipe = nil
-filament_spool_weight = 230
-slowdown_below_layer_time = 20
-
-[filament:Extrudr Flex Medium]
-inherits = *FLEX*
-filament_vendor = Extrudr
-disable_fan_first_layers = 1
-extrusion_multiplier = 1.2
-filament_cost = 39.98
-filament_density = 1.19
-filament_deretract_speed = nil
-filament_max_volumetric_speed = 3
-filament_notes = "https://www.extrudr.com/en/products/catalogue/?material=117"
-filament_retract_length = 0.4
-filament_wipe = nil
-filament_spool_weight = 230
-slowdown_below_layer_time = 20
-
-[filament:Extrudr Flex SemiSoft]
-inherits = *FLEX*
-filament_vendor = Extrudr
-disable_fan_first_layers = 1
-extrusion_multiplier = 1.2
-filament_cost = 39.98
-filament_density = 1.18
-filament_deretract_speed = nil
-filament_max_volumetric_speed = 1.8
-filament_notes = "https://www.extrudr.com/en/products/catalogue/?material=116"
-filament_retract_length = 0.4
-filament_wipe = nil
-filament_spool_weight = 230
-slowdown_below_layer_time = 20
-
-[filament:addnorth Adamant S1]
-inherits = *FLEX*
-filament_vendor = addnorth
-disable_fan_first_layers = 3
-extrusion_multiplier = 1
-filament_cost = 
-filament_density = 1.22
-temperature = 250
-bed_temperature = 50
-first_layer_temperature = 245
-first_layer_bed_temperature = 50
-slowdown_below_layer_time = 20
-min_print_speed = 20
-fan_below_layer_time = 15
-fan_always_on = 1
-cooling = 1
-min_fan_speed = 40
-max_fan_speed = 70
-bridge_fan_speed = 60
-filament_deretract_speed = nil
-filament_max_volumetric_speed = 1.7
-filament_retract_length = 0.6
-filament_retract_lift = 0.5
-filament_spool_weight = 0
-filament_retract_restart_extra = 0.1
-filament_wipe = nil
-
-[filament:addnorth Adura X]
-inherits = *PET*
-filament_vendor = addnorth
-filament_cost = 29.99
-filament_density = 1.27
-filament_type = PA
-extrusion_multiplier = 0.98
-bed_temperature = 115
-first_layer_bed_temperature = 105
-first_layer_temperature = 265
-temperature = 270
-fan_always_on = 0
-min_fan_speed = 20
-max_fan_speed = 40
-bridge_fan_speed = 70
-slowdown_below_layer_time = 10
-min_print_speed = 20
-fan_below_layer_time = 10
-disable_fan_first_layers = 3
-full_fan_speed_layer = 0
-filament_retract_length = 1.4
-filament_retract_lift = 0.4
-filament_max_volumetric_speed = 4
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.08{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
-filament_spool_weight = 0
-compatible_printers_condition = printer_notes!~/.*PRINTER_MODEL_MK(2|2.5).*/ and nozzle_diameter[0]>=0.4 and printer_model!="MINI" and printer_model!="MK2SMM" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:addnorth Adura X @MINI]
-inherits = addnorth Adura X
-filament_retract_length = nil
-filament_retract_lift = nil
-filament_retract_speed = 40
-filament_deretract_speed = 25
-bed_temperature = 60
-first_layer_bed_temperature = 60
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model=="MINI"
-
-[filament:addnorth Adura X @MMU1]
-inherits = addnorth Adura X
-filament_retract_length = nil
-filament_retract_lift = nil
-bed_temperature = 60
-first_layer_bed_temperature = 60
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model=="MK2SMM"
-
-[filament:addnorth Adura X @MK2]
-inherits = addnorth Adura X
-bed_temperature = 110
-first_layer_bed_temperature = 105
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_notes=~/.*PRINTER_MODEL_MK(2|2.5).*/ and ! (printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and single_extruder_multi_material)
-
-[filament:addnorth E-PLA]
-inherits = *PLA*
-filament_vendor = addnorth
-filament_cost = 24.99
-filament_density = 1.24
-extrusion_multiplier = 0.98
-temperature = 215
-bed_temperature = 60
-first_layer_temperature = 215
-first_layer_bed_temperature = 60
-full_fan_speed_layer = 3
-slowdown_below_layer_time = 15
-filament_spool_weight = 0
-
-[filament:addnorth ESD-PETG]
-inherits = *PET*
-filament_vendor = addnorth
-filament_cost = 29.99
-filament_density = 1.27
-extrusion_multiplier = 0.98
-bed_temperature = 80
-first_layer_bed_temperature = 85
-first_layer_temperature = 245
-temperature = 265
-fan_always_on = 1
-min_fan_speed = 15
-max_fan_speed = 30
-bridge_fan_speed = 35
-slowdown_below_layer_time = 10
-min_print_speed = 15
-fan_below_layer_time = 8
-disable_fan_first_layers = 3
-full_fan_speed_layer = 0
-filament_retract_length = 1.2
-filament_retract_lift = 0
-filament_max_volumetric_speed = 2
-filament_spool_weight = 0
-
-[filament:addnorth ESD-PETG @MINI]
-inherits = addnorth ESD-PETG
-filament_retract_length = nil
-filament_retract_speed = 40
-filament_deretract_speed = 25
-filament_max_volumetric_speed = 2
-compatible_printers_condition = printer_model=="MINI"
-
-[filament:addnorth ESD-PETG @MMU1]
-inherits = addnorth ESD-PETG
-filament_retract_length = nil
-filament_max_volumetric_speed = 2
-compatible_printers_condition = printer_model=="MK2SMM"
-
-[filament:addnorth OBC Polyethylene]
-inherits = *FLEX*
-filament_vendor = addnorth
-disable_fan_first_layers = 3
-extrusion_multiplier = 1
-filament_cost = 82
-filament_density = 1.22
-temperature = 200
-bed_temperature = 100
-first_layer_temperature = 195
-first_layer_bed_temperature = 100
-slowdown_below_layer_time = 5
-fan_below_layer_time = 15
-fan_always_on = 1
-cooling = 1
-min_fan_speed = 20
-max_fan_speed = 30
-bridge_fan_speed = 40
-min_print_speed = 20
-filament_max_volumetric_speed = 4
-filament_retract_length = nil
-filament_retract_lift = nil
-filament_retract_speed = 40
-filament_deretract_speed = 25
-filament_spool_weight = 0
-filament_notes = "Use Magigoo PP bed adhesive or PP packing tape (on a cold printbed)."
-
-[filament:addnorth PETG]
-inherits = *PET*
-filament_vendor = addnorth
-filament_cost = 29.99
-filament_density = 1.27
-bed_temperature = 80
-first_layer_bed_temperature = 85
-first_layer_temperature = 240
-temperature = 250
-fan_always_on = 1
-min_fan_speed = 15
-max_fan_speed = 40
-bridge_fan_speed = 50
-slowdown_below_layer_time = 10
-min_print_speed = 15
-fan_below_layer_time = 15
-disable_fan_first_layers = 3
-full_fan_speed_layer = 0
-filament_retract_length = 1.4
-filament_max_volumetric_speed = 8
-filament_spool_weight = 0
-
-[filament:addnorth PETG @MINI]
-inherits = addnorth PETG
-filament_retract_length = nil
-filament_retract_lift = nil
-filament_retract_speed = 40
-filament_deretract_speed = 25
-filament_max_volumetric_speed = 7
-compatible_printers_condition = printer_model=="MINI"
-
-[filament:addnorth PETG @MMU1]
-inherits = addnorth PETG
-filament_retract_length = nil
-filament_retract_lift = nil
-filament_max_volumetric_speed = 7
-compatible_printers_condition = printer_model=="MK2SMM"
-
-[filament:addnorth Rigid X]
-inherits = *PET*
-filament_vendor = addnorth
-filament_cost = 29.99
-filament_density = 1.27
-extrusion_multiplier = 0.98
-bed_temperature = 85
-first_layer_bed_temperature = 90
-first_layer_temperature = 250
-temperature = 260
-fan_always_on = 1
-min_fan_speed = 20
-max_fan_speed = 60
-bridge_fan_speed = 70
-slowdown_below_layer_time = 10
-fan_below_layer_time = 20
-min_print_speed = 20
-disable_fan_first_layers = 3
-full_fan_speed_layer = 0
-filament_retract_length = 1.4
-filament_max_volumetric_speed = 5
-filament_spool_weight = 0
-filament_notes = "Please use a nozzle that is resistant to abrasive filaments, like hardened steel."
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model!="MINI" and printer_model!="MK2SMM" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:addnorth Rigid X @MINI]
-inherits = addnorth Rigid X
-filament_retract_length = nil
-filament_retract_lift = nil
-filament_retract_speed = 40
-filament_deretract_speed = 25
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model=="MINI"
-
-[filament:addnorth Rigid X @MMU1]
-inherits = addnorth Rigid X
-filament_retract_length = nil
-filament_retract_lift = nil
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model=="MK2SMM"
-
-[filament:addnorth Textura]
-inherits = *PLA*
-filament_vendor = addnorth
-filament_cost = 24.99
-filament_density = 1.24
-extrusion_multiplier = 0.95
-temperature = 215
-bed_temperature = 65
-first_layer_temperature = 215
-first_layer_bed_temperature = 65
-min_fan_speed = 20
-max_fan_speed = 40
-bridge_fan_speed = 60
-full_fan_speed_layer = 0
-slowdown_below_layer_time = 15
-min_print_speed = 20
-filament_spool_weight = 0
-filament_retract_length = 1
-compatible_printers_condition = printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:addnorth Textura @MINI]
-inherits = addnorth Textura
-filament_retract_length = nil
-compatible_printers_condition = printer_model=="MINI"
-
-[filament:addnorth Textura @MMU1]
-inherits = addnorth Textura
-filament_retract_length = nil
-compatible_printers_condition = printer_model=="MK2SMM"
-
-[filament:Filamentworld ABS]
-inherits = *ABSC*
-filament_vendor = Filamentworld
-filament_cost = 24.9
-filament_density = 1.04
-temperature = 230
-bed_temperature = 95
-first_layer_temperature = 240
-first_layer_bed_temperature = 105
-max_fan_speed = 20
-min_fan_speed = 10
-min_print_speed = 20
-disable_fan_first_layers = 3
-fan_below_layer_time = 60
-slowdown_below_layer_time = 15
-bridge_fan_speed = 20
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Filamentworld ABS @MINI]
-inherits = Filamentworld ABS
-first_layer_bed_temperature = 100
-min_fan_speed = 15
-fan_below_layer_time = 60
-compatible_printers_condition = printer_model=="MINI"
-
-[filament:Filamentworld PETG]
-inherits = *PET*
-filament_vendor = Filamentworld
-filament_cost = 34.9
-filament_density = 1.27
-bed_temperature = 70
-first_layer_bed_temperature = 85
-first_layer_temperature = 240
-temperature = 235
-fan_always_on = 1
-min_fan_speed = 25
-max_fan_speed = 55
-bridge_fan_speed = 55
-slowdown_below_layer_time = 20
-min_print_speed = 20
-fan_below_layer_time = 35
-disable_fan_first_layers = 2
-full_fan_speed_layer = 0
-filament_retract_length = 1.4
-filament_max_volumetric_speed = 8
-filament_spool_weight = 0
-
-[filament:Filamentworld PETG @MINI]
-inherits = Filamentworld PETG
-filament_retract_length = nil
-filament_retract_lift = nil
-filament_retract_speed = 40
-filament_deretract_speed = 25
-filament_max_volumetric_speed = 7
-compatible_printers_condition = printer_model=="MINI"
-
-[filament:Filamentworld PLA]
-inherits = *PLA*
-filament_vendor = Filamentworld
-filament_cost = 24.9
-filament_density = 1.24
-temperature = 205
-bed_temperature = 55
-first_layer_temperature = 215
-first_layer_bed_temperature = 60
-full_fan_speed_layer = 3
-slowdown_below_layer_time = 10
-filament_spool_weight = 0
-min_print_speed = 20
-
-[filament:Filament PM PETG]
-inherits = *PET*
-renamed_from = "Plasty Mladec PETG"
-filament_vendor = Filament PM
-filament_cost = 27.82
-filament_density = 1.27
-filament_spool_weight = 230
-compatible_printers_condition = nozzle_diameter[0]!=0.6 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Generic PLA]
-inherits = *PLA*
-filament_vendor = Generic
-filament_cost = 25.4
-filament_density = 1.24
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:3D-Fuel Standard PLA]
-inherits = *PLA*
-filament_vendor = 3D-Fuel
-filament_cost = 22.14
-filament_density = 1.24
-filament_max_volumetric_speed = 10
-first_layer_temperature = 210
-temperature = 200
-
-[filament:3D-Fuel EasiPrint PLA]
-inherits = 3D-Fuel Standard PLA
-filament_cost = 30.44
-
-[filament:3D-Fuel Pro PLA]
-inherits = *PLA*
-filament_vendor = 3D-Fuel
-filament_cost = 26.57
-filament_density = 1.22
-filament_max_volumetric_speed = 12
-first_layer_temperature = 220
-temperature = 215
-filament_retract_lift = 0
-
-[filament:3D-Fuel Buzzed]
-inherits = 3D-Fuel Standard PLA
-filament_cost = 44.27
-filament_retract_lift = 0
-first_layer_temperature = 210
-temperature = 195
-filament_max_volumetric_speed = 8
-
-[filament:3D-Fuel Wound up]
-inherits = 3D-Fuel Buzzed
-filament_cost = 44.27
-filament_retract_lift = nil
-first_layer_temperature = 215
-temperature = 210
-filament_max_volumetric_speed = 8
-
-[filament:3D-Fuel Workday ABS]
-inherits = *ABSC*
-filament_vendor = 3D-Fuel
-filament_cost = 23.25
-filament_density = 1.04
-
-[filament:3D-Fuel Workday ABS @MINI]
-inherits = 3D-Fuel Workday ABS; *ABSMINI*
-
-[filament:Jessie PLA]
-inherits = *PLA*
-filament_vendor = Printed Solid
-filament_cost = 21
-filament_density = 1.24
-filament_max_volumetric_speed = 12
-
-[filament:Jessie PETG]
-inherits = *PET*
-filament_vendor = Printed Solid
-filament_cost = 22
-filament_density = 1.27
-first_layer_temperature = 240
-first_layer_bed_temperature = 85
-temperature = 245
-bed_temperature = 90
-filament_max_volumetric_speed = 7
-
-[filament:Jessie PETG @MINI]
-inherits = Jessie PETG; *PETMINI*
-
-[filament:Devil Design PLA]
-inherits = *PLA*
-filament_vendor = Devil Design
-filament_cost = 20.99
-filament_density = 1.24
-filament_spool_weight = 250
-
-[filament:Devil Design PETG]
-inherits = *PET*
-filament_vendor = Devil Design
-filament_cost = 20.99
-filament_density = 1.23
-filament_spool_weight = 250
-first_layer_temperature = 230
-first_layer_bed_temperature = 85
-temperature = 230
-bed_temperature = 90
-
-[filament:Spectrum PLA]
-inherits = *PLA*
-filament_vendor = Spectrum
-filament_cost = 21.50
-filament_density = 1.24
-
-[filament:Generic FLEX]
-inherits = *FLEX*
-filament_vendor = Generic
-filament_cost = 82
-filament_density = 1.22
-filament_max_volumetric_speed = 1.2
-filament_retract_length = 0
-filament_retract_speed = nil
-filament_retract_lift = nil
-compatible_printers_condition = nozzle_diameter[0]>0.35 and nozzle_diameter[0]!=0.8 and printer_model!="MK2SMM" and printer_model!="MINI" and num_extruders==1 && ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and single_extruder_multi_material)
-
-[filament:Fillamentum Flexfill 92A]
-inherits = *FLEX*
-filament_vendor = Fillamentum
-filament_cost = 33.99
-filament_density = 1.20
-filament_spool_weight = 230
-filament_max_volumetric_speed = 1.2
-filament_retract_length = 0.4
-filament_retract_speed = nil
-filament_deretract_speed = 20
-fan_always_on = 1
-cooling = 0
-max_fan_speed = 60
-min_fan_speed = 60
-disable_fan_first_layers = 4
-full_fan_speed_layer = 6
-
-[filament:AmazonBasics TPU]
-inherits = *FLEX*
-filament_vendor = AmazonBasics
-fan_always_on = 1
-filament_max_volumetric_speed = 1.8
-extrusion_multiplier = 1.14
-first_layer_temperature = 235
-first_layer_bed_temperature = 50
-temperature = 235
-bed_temperature = 50
-bridge_fan_speed = 100
-max_fan_speed = 80
-min_fan_speed = 80
-filament_retract_before_travel = 3
-filament_cost = 19.99
-filament_density = 1.21
-filament_retract_length = 2
-filament_retract_speed = 45
-filament_deretract_speed = 20
-filament_retract_lift = 0
-filament_wipe = 0
-disable_fan_first_layers = 4
-full_fan_speed_layer = 6
-min_print_speed = 15
-slowdown_below_layer_time = 10
-cooling = 1
-
-[filament:SainSmart TPU]
-inherits = *FLEX*
-filament_vendor = SainSmart
-fan_always_on = 1
-filament_max_volumetric_speed = 2.5
-extrusion_multiplier = 1.1
-first_layer_temperature = 230
-first_layer_bed_temperature = 50
-temperature = 230
-bed_temperature = 50
-bridge_fan_speed = 100
-max_fan_speed = 80
-min_fan_speed = 80
-filament_retract_before_travel = 3
-filament_cost = 32.99
-filament_density = 1.21
-filament_retract_length = 1
-filament_retract_speed = nil
-filament_deretract_speed = 25
-filament_retract_lift = 0
-filament_wipe = 0
-disable_fan_first_layers = 4
-full_fan_speed_layer = 6
-min_print_speed = 15
-slowdown_below_layer_time = 10
-cooling = 1
-
-[filament:Filatech FilaFlex40]
-inherits = *FLEX*
-filament_vendor = Filatech
-fan_always_on = 1
-filament_max_volumetric_speed = 2.5
-extrusion_multiplier = 1.1
-first_layer_temperature = 230
-first_layer_bed_temperature = 50
-temperature = 230
-bed_temperature = 50
-bridge_fan_speed = 100
-max_fan_speed = 50
-min_fan_speed = 50
-filament_retract_before_travel = 3
-filament_cost = 84.68
-filament_density = 1.22
-filament_retract_length = 2
-filament_retract_speed = 50
-filament_deretract_speed = 25
-filament_retract_lift = 0
-filament_wipe = 0
-disable_fan_first_layers = 4
-full_fan_speed_layer = 6
-min_print_speed = 15
-slowdown_below_layer_time = 10
-cooling = 1
-
-[filament:Filatech FilaFlex30]
-inherits = Filatech FilaFlex40
-temperature = 225
-filament_density = 1.15
-extrusion_multiplier = 1.1
-filament_cost =
-
-[filament:Filatech FilaFlex55]
-inherits = Filatech FilaFlex40
-temperature = 230
-filament_density = 1.18
-bed_temperature = 60
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_cost =
-first_layer_temperature = 235
-extrusion_multiplier = 1
-
-# [filament:Filatech TPE]
-# inherits = Filatech FilaFlex40
-# first_layer_temperature = 230
-# temperature = 225
-# filament_density = 1.2
-# fan_below_layer_time = 60
-# max_fan_speed = 80
-# min_fan_speed = 80
-# fan_always_on = 1
-
-[filament:Filatech TPU]
-inherits = Filatech FilaFlex40
-first_layer_temperature = 230
-filament_density = 1.2
-fan_below_layer_time = 60
-max_fan_speed = 80
-min_fan_speed = 80
-fan_always_on = 1
-temperature = 235
-
-[filament:Filatech ABS]
-inherits = *ABSC*
-filament_vendor = Filatech
-filament_cost = 
-extrusion_multiplier = 0.95
-filament_density = 1.05
-
-[filament:Filatech ABS @MINI]
-inherits = Filatech ABS; *ABSMINI*
-
-[filament:Filatech FilaCarbon]
-inherits = *ABSC*
-filament_vendor = Filatech
-filament_cost = 
-extrusion_multiplier = 0.95
-filament_density = 1.1
-first_layer_bed_temperature = 105
-bed_temperature = 100
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Filatech FilaCarbon @MINI]
-inherits = Filatech FilaCarbon; *ABSMINI*
-first_layer_bed_temperature = 100
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model=="MINI"
-
-[filament:Filatech FilaPLA]
-inherits = *PLA*
-filament_vendor = Filatech
-filament_cost = 
-filament_density = 1.3
-first_layer_temperature = 235
-first_layer_bed_temperature = 50
-temperature = 230
-bed_temperature = 55
-
-[filament:Filatech PLA]
-inherits = *PLA*
-filament_vendor = Filatech
-filament_cost = 
-filament_density = 1.25
-first_layer_temperature = 215
-temperature = 210
-
-[filament:Filatech PLA+]
-inherits = Filatech PLA
-filament_density = 1.24
-
-[filament:Filatech FilaTough]
-inherits = Filatech ABS
-filament_cost = 
-extrusion_multiplier = 0.95
-filament_density = 1.29
-first_layer_temperature = 245
-first_layer_bed_temperature = 80
-temperature = 240
-bed_temperature = 90
-cooling = 0
-compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Filatech HIPS]
-inherits = Prusa HIPS
-filament_vendor = Filatech
-filament_cost = 
-filament_density = 1.07
-filament_spool_weight = 
-first_layer_temperature = 230
-first_layer_bed_temperature = 100
-temperature = 225
-bed_temperature = 110
-compatible_printers_condition = printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Filatech HIPS @MINI]
-inherits = Filatech HIPS; *ABSMINI*
-
-[filament:Filatech PA]
-inherits = *ABSC*
-filament_vendor = Filatech
-filament_cost = 
-filament_density = 1.1
-first_layer_temperature = 275
-first_layer_bed_temperature = 110
-temperature = 275
-bed_temperature = 115
-fan_always_on = 0
-cooling = 0
-bridge_fan_speed = 25
-filament_type = PA
-filament_max_volumetric_speed = 8
-compatible_printers_condition = printer_notes!~/.*PRINTER_MODEL_MK(2|2.5).*/ and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Filatech PA @MK2]
-inherits = Filatech PA
-first_layer_bed_temperature = 105
-bed_temperature = 110
-compatible_printers_condition = printer_notes=~/.*PRINTER_MODEL_MK(2|2.5).*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Filatech PA @MINI]
-inherits = Filatech PA
-first_layer_bed_temperature = 100
-bed_temperature = 100
-compatible_printers_condition = printer_model=="MINI"
-
-[filament:Filatech PC]
-inherits = Filatech PA
-first_layer_bed_temperature = 110
-bed_temperature = 115
-filament_density = 1.2
-filament_type = PC
-
-[filament:Filatech PC @MK2]
-inherits = Filatech PC
-first_layer_bed_temperature = 105
-bed_temperature = 110
-compatible_printers_condition = printer_notes=~/.*PRINTER_MODEL_MK(2|2.5).*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Filatech PC-ABS]
-inherits = Filatech PC
-first_layer_temperature = 270
-temperature = 270
-first_layer_bed_temperature = 110
-bed_temperature = 115
-filament_density = 1.08
-filament_type = PC
-fan_always_on = 0
-cooling = 1
-extrusion_multiplier = 0.95
-disable_fan_first_layers = 6
-
-[filament:Filatech PC-ABS @MK2]
-inherits = Filatech PC-ABS
-first_layer_bed_temperature = 105
-bed_temperature = 110
-compatible_printers_condition = printer_notes=~/.*PRINTER_MODEL_MK(2|2.5).*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Filatech PETG]
-inherits = *PET*
-filament_vendor = Filatech
-filament_cost = 
-filament_density = 1.27
-first_layer_temperature = 240
-first_layer_bed_temperature = 75
-temperature = 245
-bed_temperature = 80
-extrusion_multiplier = 0.95
-fan_always_on = 0
-
-[filament:Filatech PETG @MINI]
-inherits = Filatech PETG; *PETMINI*
-
-[filament:Filatech Wood-PLA]
-inherits = Filatech PLA
-filament_cost = 
-filament_density = 1.05
-first_layer_temperature = 210
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Ultrafuse PET]
-inherits = *PET*
-filament_vendor = BASF
-filament_cost = 
-filament_density = 1.33
-filament_colour = #F7F7F7
-first_layer_temperature = 220
-first_layer_bed_temperature = 70
-temperature = 215
-bed_temperature = 70
-fan_below_layer_time = 10
-min_fan_speed = 75
-max_fan_speed = 100
-bridge_fan_speed = 100
-filament_type = PET
-disable_fan_first_layers = 1
-full_fan_speed_layer = 3
-filament_notes = "Material Description\nUltrafuse PET is made from a premium PET and prints as easy as PLA, but is much stronger. The filament has a large operating window for printing (temperature vs. speed), so it can be used on every 3D-printer. PET will give you outstanding printing results: a good layer adhesion, a high resolution and it is easy to handle. Ultrafuse PET can be 100% recycled, is watertight and has great colors and finish.\n\nPrinting Recommendations:\nUltrafuse PET can be printed directly onto a clean build plate. For challenging prints, use 3dLac to improve adhesion."
-filament_retract_length = 2
-filament_retract_speed = 40
-filament_retract_before_travel = 2
-filament_wipe = 0
-filament_retract_layer_change = 0
-filament_retract_lift = 0
-
-[filament:Ultrafuse PET @MINI]
-inherits = Ultrafuse PET; *PETMINI*
-
-[filament:Ultrafuse PRO1]
-inherits = Prusament PLA
-filament_vendor = BASF
-filament_cost = 
-filament_density = 1.25
-filament_spool_weight = 0
-filament_colour = #FFFFFF
-filament_notes = "Material Description\nPLA PRO1 is an extremely versatile tough PLA filament made for professionals. It reduces your printing time by 30% – 80%, (subject to printer and object limitations) and the strength exceeds overall mechanical properties of printed ABS parts. Printer settings can be tuned to achieve blazing fast speeds or an unrivaled surface finish. The excellent quality control ensures the highest levels of consistency between colors and batches, it will perform as expected, every time.\n\nPrinting Recommendations:\nUltrafuse PLA PRO1 can be printed directly onto a clean build plate."
-filament_retract_length = 2
-filament_retract_lift = 0
-filament_retract_speed = 40
-filament_retract_before_travel = 2
-filament_retract_layer_change = 0
-compatible_printers_condition = printer_model!="MINI" and printer_model!="MK2SMM" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Ultrafuse PRO1 @MINI]
-inherits = Ultrafuse PRO1
-filament_retract_length = nil
-filament_retract_speed = nil
-filament_retract_before_travel = nil
-filament_retract_layer_change = nil
-compatible_printers_condition = printer_model=="MINI"
-
-[filament:Ultrafuse ABS]
-inherits = *ABSC*
-filament_vendor = BASF
-filament_cost = 
-filament_density = 1.04
-min_fan_speed = 10
-max_fan_speed = 20
-bed_temperature = 100
-disable_fan_first_layers = 3
-filament_colour = #FFFFFF
-filament_notes = "Material Description\nABS is the second most used 3D printing material. It is strong, flexible and has a high heat resistance. ABS is a preferred plastic for engineers and professional applications. ABS can be smoothened with acetone. To make a proper 3D print with ABS you will need a heated print bed. The filament is available in 9 colors.\n\nPrinting Recommendations:\n\nApply Tape, adhesion spray or glue to a clean build plate to improve adhesion."
-filament_retract_before_travel = 2
-filament_wipe = 0
-filament_retract_layer_change = 0
-
-[filament:Ultrafuse ABS @MINI]
-inherits = Ultrafuse ABS; *ABSMINI*
-filament_retract_layer_change = nil
-
-[filament:Ultrafuse ABS Fusion+]
-inherits = Ultrafuse ABS
-filament_density = 1.08
-first_layer_bed_temperature = 105
-temperature = 250
-filament_colour = #FFF8D9
-filament_notes = "Material Description\nABS Fusion+ made with Polyscope XILOY™ 3D is an engineering filament which has been optimized for 3D-printing. This special grade has been developed in collaboration with Polyscope Polymers - renowned for its material solutions in the automotive industry. ABS is a thermoplastic which is used in many applications. Although ABS has been classified as a standard material in 3D-printing it is known to be quite challenging to process. ABS Fusion+ combines the properties of ABS with an improved processability. The filament is based on an ABS grade which can be directly printed on glass without any adhesives or tape and has a higher success rate of prints due to extreme low warping."
-filament_retract_before_travel = 2
-filament_wipe = nil
-filament_retract_layer_change = 0
-filament_retract_lift = 0
-
-[filament:Ultrafuse ABS Fusion+ @MINI]
-inherits = Ultrafuse ABS Fusion+; *ABSMINI*
-first_layer_bed_temperature = 100
-filament_retract_layer_change = nil
-
-[filament:Ultrafuse ASA]
-inherits = Ultrafuse ABS Fusion+
-filament_density = 1.07
-filament_colour = #FFF4CA
-first_layer_temperature = 275
-temperature = 275
-first_layer_bed_temperature = 110
-bed_temperature = 105
-filament_type = ASA
-min_fan_speed = 25
-max_fan_speed = 50
-bridge_fan_speed = 100
-disable_fan_first_layers = 4
-filament_max_volumetric_speed = 5
-filament_notes = "Material Description\nUltrafuse ASA is a high-performance thermoplastic with similar mechanical properties as ABS. ASA offers additional benefits such as high outdoor weather resistance. The UV resistance, toughness, and rigidity make it an ideal material to 3D-print outdoor fixtures and appliances without losing its properties or color. When also taking into account the high heat resistance and high chemical resistance, this filament is a good choice for many types of applications.\n\nPrinting Recommendations:\nApply Magigoo PC, 3D lac or Dimafix to a clean build plate to improve adhesion."
-
-[filament:Ultrafuse ASA @MINI]
-inherits = Ultrafuse ASA; *ABSMINI*
-filament_type = ASA
-
-[filament:Ultrafuse HIPS]
-inherits = Ultrafuse ABS
-temperature = 250
-filament_density = 1.02
-filament_type = HIPS
-min_fan_speed = 20
-max_fan_speed = 20
-filament_soluble = 1
-filament_notes = "Material Description\nUltrafuse HIPS is a high-quality engineering thermoplastic, which is well known in the 3D-printing industry as a support material for ABS. But this material has additional properties to offer like good impact resistance, good dimensional stability, and easy post-processing. HiPS is a great material to use as a support for ABS because there is a good compatibility between the two materials, and HIPS is an easy breakaway support. Now you have the opportunity to create ABS models with complex geometry. HIPS is easy to post process with glue or with sanding paper."
-
-[filament:Ultrafuse HIPS @MINI]
-inherits = Ultrafuse HIPS; *ABSMINI*
-filament_type = HIPS
-min_fan_speed = 20
-max_fan_speed = 20
-
-[filament:Ultrafuse PA]
-inherits = Fillamentum Nylon FX256
-filament_vendor = BASF
-filament_density = 1.12
-filament_colour = #ECFAFF
-first_layer_temperature = 240
-temperature = 240
-first_layer_bed_temperature = 80
-bed_temperature = 70
-min_fan_speed = 0
-max_fan_speed = 0
-bridge_fan_speed = 0
-fan_below_layer_time = 30
-slowdown_below_layer_time = 20
-min_print_speed = 15
-filament_max_volumetric_speed = 11
-filament_retract_length = 1
-filament_retract_lift = 0
-filament_retract_before_travel = 2
-filament_retract_layer_change = 0
-filament_cost = 0
-filament_spool_weight = 0
-compatible_printers_condition = printer_model!="MINI" and printer_model!="MK2SMM" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-filament_notes = "Material Description\nThe key features of Ultrafuse PA are the high strength and high modulus. Furthermore, Ultrafuse PA shows a good thermal distortion stability.\n\nPrinting Recommendations:\nApply PVA glue, Kapton tape or PA adhesive to a clean buildplate to improve adhesion."
-
-[filament:Ultrafuse PA6 GF30]
-inherits = Ultrafuse PA
-filament_density = 1.17
-first_layer_temperature = 270
-temperature = 270
-first_layer_bed_temperature = 100
-bed_temperature = 100
-filament_colour = #404040
-fan_always_on = 1
-min_fan_speed = 0
-max_fan_speed = 50
-bridge_fan_speed = 100
-disable_fan_first_layers = 1
-full_fan_speed_layer = 3
-slowdown_below_layer_time = 15
-filament_max_volumetric_speed = 10
-filament_retract_length = 1.2
-filament_retract_speed = 40
-filament_deretract_speed = 30
-filament_retract_lift = nil
-filament_wipe = 0
-filament_notes = "Material Description\nUltrafuse® PA6 GF30 is a unique compound specifically developed for FFF printing. Due to the glass fiber content of 30%, parts tend to warp less. In addition the excellent layer adhesion and its compatibility with the water soluble support Ultrafuse® BVOH make this material the perfect solution to develop industrial applications on an FFF printer.\n\nWith its high wear and chemical resistance, high stiffness and strength, Ultrafuse® PA6 GF30 is perfect for a wide variety of applications in automotive, electronics or transportation.\n\nUltrafuse PA6 GF30 is designed for functional prototyping and demanding applications such as industrial tooling, transportation, electronics, small appliances, sports & leisure\n\nPrinting Recommendations:\nThis material contains fibers that have an abrasive effect on printer components. Use a hardened or Ruby nozzle with a diameter of 0.6 or larger for optimal performance and avoid damage to the nozzle.\n\nUltrafuse PA6 GF30 can be printed directly onto a clean build plate. For challenging prints, use Magigoo PA gluestick  to improve adhesion."
-compatible_printers_condition = nozzle_diameter[0]>=0.6 and printer_model!="MINI" and printer_model!="MK2SMM" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Ultrafuse PAHT-CF15]
-inherits = Ultrafuse PA6 GF30
-filament_density = 1.23
-filament_notes = "Material Description\nPAHT CF15 is a high-performance 3D printing filament that opens new application fields in FFF printing. In parallel to its advanced mechanical properties, dimensional stability, and chemical resistance, it has very good processability. It works in any FFF printer with a hardened nozzle. In addition to that, it is compatible with water-soluble support material and HiPS, which allow printing complex geometries that work in challenging environments. PAHT CF15 has high heat resistance up to 130 °C and low moisture absorption.\n\nPrinting Recommendations:\nThis material contains fibers that have an abrasive effect on printer components. Use a hardened or Ruby nozzle with a diameter of 0.6 or larger for optimal performance and avoid damage to the nozzle.\n\nUltrafuse PAHT-CF can be printed directly onto a clean build plate. For challenging prints, use 3dLac to improve adhesion."
-
-[filament:Ultrafuse PC-ABS-FR]
-inherits = Ultrafuse ABS
-filament_colour = #505050
-filament_density = 1.17
-first_layer_temperature = 275
-temperature = 275
-first_layer_bed_temperature = 110
-bed_temperature = 105
-filament_type = PC
-filament_max_volumetric_speed = 8
-filament_wipe = nil
-min_fan_speed = 20
-max_fan_speed = 20
-bridge_fan_speed = 30
-disable_fan_first_layers = 4
-compatible_printers_condition = printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-filament_notes = "Material Description\nUltrafuse® PC/ABS FR Black is a V-0 flame retardant blend of Polycarbonate and ABS – two of the most used thermoplastics for engineering & electrical applications. The combination of these two materials results in a premium material with a mix of the excellent mechanical properties of PC and the comparably low printing temperature of ABS. Combined with a halogen free flame retardant, parts printed with Ultrafuse® PC/ABS FR Black feature great tensile and impact strength, higher thermal resistance than ABS and can fulfill the requirements of the UL94 V-0 standard.\n\nPrinting Recommendations:\nApply Magigoo PC to a clean build plate to improve adhesion."
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.07{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
-
-[filament:Ultrafuse PET-CF15]
-inherits = Ultrafuse PET
-filament_density = 1.36
-filament_colour = #404040
-first_layer_temperature = 270
-temperature = 270
-first_layer_bed_temperature = 75
-bed_temperature = 75
-min_fan_speed = 60
-max_fan_speed = 100
-bridge_fan_speed = 100
-disable_fan_first_layers = 1
-full_fan_speed_layer = 3
-slowdown_below_layer_time = 15
-fan_below_layer_time = 30
-filament_max_volumetric_speed = 10
-filament_retract_length = 1.2
-filament_retract_speed = 40
-filament_deretract_speed = 30
-filament_retract_lift = nil
-filament_wipe = 0
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0"
-filament_notes = "Material Description\nPET CF15 is a Carbon Fiber reinforced PET which has precisely tuned material properties, for a wide range of technical applications. The filament is very strong and stiff and has high heat resistance. With its high dimensional stability and low abrasiveness, the filament offers an easy to print experience which allows direct printing on glass or a PEI sheet. It is compatible with HiPS for breakaway support and water soluble support and has an excellent surface finish.\n\nPrinting Recommendations:\nThis material contains fibers that have an abrasive effect on printer components. Use a hardened or Ruby nozzle with a diameter of 0.6 or larger for optimal performance and avoid damage to the nozzle.\n\nUltrafuse PET-CF15 can be printed directly onto a clean build plate. For challenging prints, use 3dLac to improve adhesion."
-compatible_printers_condition = nozzle_diameter[0]>=0.6 and printer_model!="MINI" and printer_model!="MK2SMM" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Ultrafuse PLA]
-inherits = *PLA*
-filament_vendor = BASF
-filament_density = 1.25
-full_fan_speed_layer = 3
-filament_notes = "Material Description\nPLA is one of the most used materials for 3D printing. Ultrafuse PLA is available in a wide range of colors. The glossy feel often attracts those who print display models or items for household use. Many appreciate the plant-based origin of this material. When properly cooled, PLA has a high maximum printing speed and sharp printed corners. Combining this with low warping of the print makes it a popular plastic for home printers, hobbyists, prototyping and schools.\n\nPrinting Recommendations:\nUltrafuse PLA can be printed directly onto a clean build plate."
-
-[filament:Ultrafuse PP]
-inherits = Ultrafuse ABS
-filament_density = 0.91
-filament_colour = #F0F0F0
-first_layer_temperature = 240
-temperature = 240
-first_layer_bed_temperature = 80
-bed_temperature = 70
-min_fan_speed = 100
-max_fan_speed = 100
-bridge_fan_speed = 100
-disable_fan_first_layers = 1
-full_fan_speed_layer = 3
-fan_below_layer_time = 60
-slowdown_below_layer_time = 20
-min_print_speed = 10
-filament_type = PP
-filament_max_volumetric_speed = 2.5
-filament_retract_speed = 25
-filament_deretract_speed = 25
-filament_retract_layer_change = 0
-filament_wipe = nil
-filament_notes = "Material Description\nUltrafuse PP is high-performance thermoplastic with low density, high elasticity and high resistance to fatigue. The mechanical properties make it an ideal material for 3D-printing applications which have to endure high stress or strain. The filament has high chemical resistance and a high isolation value. PP is one of the most used materials in the world, due to its versatility and ability to engineer lightweight tough parts.\n\nPrinting Recommendations:\nApply PP tape or Magigoo PP adhesive to the buildplate for optimal adhesion."
-compatible_printers_condition = printer_model!="MINI" and printer_model!="MK2SMM" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Ultrafuse PP-GF30]
-inherits = Ultrafuse PP
-filament_density = 1.07
-filament_colour = #404040
-first_layer_temperature = 260
-temperature = 250
-first_layer_bed_temperature = 90
-bed_temperature = 40
-min_fan_speed = 40
-max_fan_speed = 75
-fan_always_on = 1
-fan_below_layer_time = 30
-slowdown_below_layer_time = 15
-min_print_speed = 15
-filament_retract_length = 1.2
-filament_retract_speed = 40
-filament_deretract_speed = 30
-filament_retract_lift = nil
-filament_wipe = 0
-filament_notes = "Ultrafuse PP GF30 is polypropylene, reinforced with 30% glass fiber content. The fibers in this compound are specially designed for 3D-printing filaments and are compatible with a wide range of standard FFF 3D-printers. The extreme stiffness makes this material highly suitable for demanding applications. Other key properties of PPGF30 are high heat resistance and improved UV-resistance. All these excellent properties make this filament highly suitable in an industrial environment.\n\nPrinting Recommendations:\nThis material contains fibers that have an abrasive effect on printer components. Use a hardened or Ruby nozzle with a diameter of 0.6 or larger for optimal performance and avoid damage to the nozzle.\n\nApply PP strapping tape or PPGF adhesive to a clean build plate for optimal adhesion."
-compatible_printers_condition = nozzle_diameter[0]>=0.6 and printer_model!="MINI" and printer_model!="MK2SMM" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Ultrafuse TPC-45D]
-inherits = *FLEX*
-filament_vendor = BASF
-extrusion_multiplier = 1
-filament_density = 1.15
-filament_colour = #0035EC
-first_layer_temperature = 235
-temperature = 235
-first_layer_bed_temperature = 60
-bed_temperature = 60
-min_fan_speed = 10
-max_fan_speed = 50
-bridge_fan_speed = 80
-fan_below_layer_time = 30
-slowdown_below_layer_time = 15
-min_print_speed = 15
-fan_always_on = 1
-cooling = 1
-filament_max_volumetric_speed = 1.2
-filament_retract_length = 1.2
-filament_retract_speed = 25
-filament_deretract_speed = 25
-filament_retract_lift = 0
-filament_wipe = nil
-filament_retract_before_wipe = nil
-filament_retract_before_travel = 2
-filament_retract_layer_change = 0
-filament_notes = "Material Description\nTPC 45D is a flexible, shore 45D, rubber-like Thermoplastic Copolyester Elastomer (TPE-C), which is derived from rapeseed oil and combines the best properties of elastomers (rubbers) and polyesters. The material delivers excellent adhesion in the Z-direction, meaning that the printed layers do not detach - even with extreme deformation.\n\nPrinting Recommendations:\nApply Magigoo Flex to a clean build plate to improve adhesion."
-
-## [filament:Ultrafuse TPS-90A]
-## inherits = Ultrafuse TPC-45D
-## filament_density = 1.04
-## extrusion_multiplier = 1.02
-## filament_colour = #FFFFFF
-## first_layer_temperature = 270
-## temperature = 265
-## first_layer_bed_temperature = 30
-## bed_temperature = 30
-## min_fan_speed = 20
-## max_fan_speed = 75
-## filament_notes = "Material Description\nUltrafuse® TPS 90A is an elastomer based on the raw material SEBS. The combination of durable and flexible building blocks leads to a very versatile material. Compared to other flexible 3D printing materials it shows more rubber-like soft touch haptics and better non-slip properties. Furthermore, the material shows a reduced moisture uptake, which allows for printing without pre-drying. Parts printed with Ultrafuse® TPS 90A show almost no visible layers or warpage, which makes it an excellent material choice for end-use parts. Producing multi-material parts is possible by printing it together with ABS.\n\nPrinting Recommendations:\nApply Tape, adhesion spray or glue to a clean build plate to improve adhesion."
-
-[filament:Ultrafuse TPU-64D]
-inherits = Ultrafuse TPC-45D
-filament_density = 1.16
-first_layer_temperature = 230
-temperature = 225
-first_layer_bed_temperature = 40
-bed_temperature = 40
-min_fan_speed = 20
-max_fan_speed = 100
-filament_notes = "Material Description\nUltrafuse® TPU 64D is the hardest elastomer in BASF Forward AM’s flexible productline. The material shows a relatively high rigidity while maintaining a certain flexibility. This filament is the perfect match for industrial applications requiring rigid parts being resistant to impact, wear and tear. Due to its property profile, the material can be used as an alternative for parts made from ABS and rubbers. Ultrafuse® TPU 64D is easy to print on direct drive and bowden style printers and is compatible with soluble BVOH support to realize the most complex geometries.\n\nPrinting Recommendations:\nUltrafuse TPU can be printed directly onto a clean build plate. A small amount of 3Dlac can make removal easier after printing."
-
-[filament:Ultrafuse TPU-85A]
-inherits = Ultrafuse TPU-64D
-filament_density = 1.11
-first_layer_temperature = 225
-temperature = 220
-filament_notes = "Material Description\nUltrafuse® TPU 85A comes in its natural white color. Chemical properties (e.g. resistance against particular substances) and tolerance for solvents can be made available, if these factors are relevant for a specific application. Generally, these properties correspond to publicly available data on polyether based TPUs. This material is not FDA conform. Good flexibility at low temperature, good wear performance and good damping behavior are the key features of Ultrafuse® TPU 85A.\n\nPrinting Recommendations:\nUltrafuse TPU can be printed directly onto a clean build plate. A small amount of 3Dlac can make removal easier after printing."
-
-[filament:Ultrafuse TPU-95A]
-inherits = Ultrafuse TPU-85A
-filament_density = 1.14
-first_layer_temperature = 230
-temperature = 225
-filament_notes = "Material Description\nUltrafuse® TPU 95A comes with a well-balanced profile of flexibility and durability. On top of that, it allows for easier and faster printing then softer TPU grades. Parts printed with Ultrafuse® TPU 95A show a high elongation, good impact resistance, excellent layer adhesion and a good resistance to oils and common industrially used chemicals. Due to its good printing behavior, Ultrafuse® TPU 95A is a good choice for starting printing flexible materials on both direct drive and bowden style printers.\n\nPrinting Recommendations:\nUltrafuse TPU can be printed directly onto a clean build plate. A small amount of 3Dlac can make removal easier after printing."
-
-[filament:Ultrafuse rPET]
-inherits = Ultrafuse PET
-filament_density = 1.27
-filament_colour = #9DC5FF
-first_layer_temperature = 235
-temperature = 235
-first_layer_bed_temperature = 80
-bed_temperature = 75
-min_fan_speed = 50
-max_fan_speed = 100
-fan_below_layer_time = 15
-filament_notes = "Material Description\nPET is mainly known by the well-known PET bottle material. This recycled has a natural transparent blueish look. It has excellent 3D printing properties and good mechanical characteristics."
-filament_retract_length = 1.2
-filament_retract_lift = 0.6
-filament_wipe = nil
-
-[filament:Ultrafuse Metal]
-inherits = *ABSC*
-renamed_from = "Ultrafuse 17-4 PH"
-filament_vendor = BASF
-filament_cost = 
-filament_density = 4.5
-extrusion_multiplier = 1.08
-first_layer_temperature = 250
-first_layer_bed_temperature = 100
-temperature = 250
-bed_temperature = 100
-min_fan_speed = 0
-max_fan_speed = 0
-bridge_fan_speed = 0
-cooling = 0
-fan_always_on = 0
-filament_max_volumetric_speed = 4
-filament_type = METAL
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-start_filament_gcode = "M900 K0"
-filament_colour = #FFFFFF
-
-[filament:Polymaker PC-Max]
-inherits = *ABS*
-filament_vendor = Polymaker
-filament_cost = 77.3
-filament_density = 1.20
-filament_type = PC
-bed_temperature = 115
-filament_colour = #FFF2EC
-first_layer_bed_temperature = 100
-first_layer_temperature = 270
-temperature = 270
-bridge_fan_speed = 0
-filament_max_volumetric_speed = 8
-
-[filament:PrimaSelect PVA+]
-inherits = *PLA*
-filament_vendor = PrimaSelect
-filament_cost = 122.1
-filament_density = 1.23
-cooling = 0
-fan_always_on = 0
-filament_colour = #FFFFD7
-filament_max_volumetric_speed = 3.8
-filament_ramming_parameters = "120 100 8.3871 8.6129 8.93548 9.22581 9.48387 9.70968 9.87097 10.0323 10.2258 10.4194 10.6452 10.8065| 0.05 8.34193 0.45 8.73548 0.95 9.34836 1.45 9.78385 1.95 10.0871 2.45 10.5161 2.95 10.8903 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-filament_soluble = 1
-filament_type = PVA
-first_layer_temperature = 195
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-temperature = 195
-
-[filament:Prusa ABS]
-inherits = *ABSC*
-filament_vendor = Made for Prusa
-filament_cost = 27.82
-filament_density = 1.08
-filament_spool_weight = 230
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:*ABS MMU2*]
-inherits = Prusa ABS
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-filament_cooling_final_speed = 50 
-filament_cooling_initial_speed = 10
-filament_cooling_moves = 5
-filament_ramming_parameters = "120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6";
-filament_loading_speed_start = 19
-filament_load_time = 15
-filament_unload_time = 12
-filament_loading_speed = 14
-filament_unloading_speed = 20
-
-[filament:Generic ABS @MMU2]
-inherits = *ABS MMU2*
-filament_vendor = Generic
-
-[filament:Generic ABS @MMU2 0.25]
-inherits = Generic ABS @MMU2
-filament_max_volumetric_speed = 1.7
-filament_ramming_parameters = "200 110 3.41935 3.6129 3.93548 4.35484 4.87097 5.51613 6.25806 7.06452 7.80645 8.35484 8.70968 8.83871| 0.05 3.37419 0.45 3.70322 0.95 4.5742 1.45 5.78387 1.95 7.44194 2.45 8.58065 2.95 8.89045 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6"
-compatible_printers_condition = nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Generic PLA @MMU2 0.25]
-inherits = Generic PLA @MMU2
-filament_max_volumetric_speed = 3
-filament_minimal_purge_on_wipe_tower = 10
-filament_ramming_parameters = "200 120 2.70968 2.93548 3.29032 3.80645 4.58065 5.54839 6.54839 7.3871 7.93548 8.19355 8.16129 8.03226| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 7.98716 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
-compatible_printers_condition = nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Prusa PLA @MMU2 0.25]
-inherits = Generic PLA @MMU2 0.25
-
-[filament:Prusament PLA @MMU2 0.25]
-inherits = Prusament PLA @MMU2
-filament_max_volumetric_speed = 3
-filament_minimal_purge_on_wipe_tower = 10
-filament_ramming_parameters = "200 120 2.70968 2.93548 3.29032 3.80645 4.58065 5.54839 6.54839 7.3871 7.93548 8.19355 8.16129 8.03226| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 7.98716 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
-compatible_printers_condition = nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Prusament PVB @MMU2 0.25]
-inherits = Prusament PVB @MMU2
-filament_max_volumetric_speed = 2
-filament_minimal_purge_on_wipe_tower = 10
-filament_ramming_parameters = "200 110 1.74194 1.90323 2.16129 2.48387 2.83871 3.25806 3.83871 4.6129 5.41935 5.96774| 0.05 1.69677 0.45 1.96128 0.95 2.63872 1.45 3.46129 1.95 4.99031 2.45 6.12908 2.95 8.30974 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
-compatible_printers_condition = nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Prusament ASA @MMU2 0.25]
-inherits = Prusament ASA @MMU2
-filament_max_volumetric_speed = 1.7
-filament_minimal_purge_on_wipe_tower = 10
-filament_ramming_parameters = "200 110 3.41935 3.6129 3.93548 4.35484 4.87097 5.51613 6.25806 7.06452 7.80645 8.35484 8.70968 8.83871| 0.05 3.37419 0.45 3.70322 0.95 4.5742 1.45 5.78387 1.95 7.44194 2.45 8.58065 2.95 8.89045 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6"
-compatible_printers_condition = nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Prusament PC Blend @MMU2 0.25]
-inherits = Prusament PC Blend @MMU2
-filament_max_volumetric_speed = 2
-filament_minimal_purge_on_wipe_tower = 10
-filament_ramming_parameters = "200 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
-compatible_printers_condition = nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Prusa ABS @MMU2 0.25]
-inherits = Prusa ABS @MMU2
-filament_max_volumetric_speed = 1.7
-filament_minimal_purge_on_wipe_tower = 10
-filament_ramming_parameters = "200 110 3.41935 3.6129 3.93548 4.35484 4.87097 5.51613 6.25806 7.06452 7.80645 8.35484 8.70968 8.83871| 0.05 3.37419 0.45 3.70322 0.95 4.5742 1.45 5.78387 1.95 7.44194 2.45 8.58065 2.95 8.89045 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6"
-compatible_printers_condition = nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Generic PETG @MMU2 0.25]
-inherits = Generic PETG @MMU2
-filament_max_volumetric_speed = 2
-filament_minimal_purge_on_wipe_tower = 10
-filament_ramming_parameters = "200 140 4.70968 4.74194 4.77419 4.80645 4.83871 4.87097 4.90323 5 5.25806 5.67742 6.29032 7.06452 7.83871 8.3871| 0.05 4.72901 0.45 4.73545 0.95 4.83226 1.45 4.88067 1.95 5.05483 2.45 5.93553 2.95 7.53556 3.45 8.6323 3.95 7.6 4.45 7.6 4.95 7.6"
-compatible_printers_condition = nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Prusa PETG @MMU2 0.25]
-inherits = Prusa PETG @MMU2
-filament_max_volumetric_speed = 2
-filament_minimal_purge_on_wipe_tower = 10
-filament_ramming_parameters = "200 140 4.70968 4.74194 4.77419 4.80645 4.83871 4.87097 4.90323 5 5.25806 5.67742 6.29032 7.06452 7.83871 8.3871| 0.05 4.72901 0.45 4.73545 0.95 4.83226 1.45 4.88067 1.95 5.05483 2.45 5.93553 2.95 7.53556 3.45 8.6323 3.95 7.6 4.45 7.6 4.95 7.6"
-compatible_printers_condition = nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Prusament PETG @MMU2 0.25]
-inherits = Prusament PETG @MMU2
-filament_max_volumetric_speed = 2
-filament_minimal_purge_on_wipe_tower = 10
-filament_ramming_parameters = "200 140 4.70968 4.74194 4.77419 4.80645 4.83871 4.87097 4.90323 5 5.25806 5.67742 6.29032 7.06452 7.83871 8.3871| 0.05 4.72901 0.45 4.73545 0.95 4.83226 1.45 4.88067 1.95 5.05483 2.45 5.93553 2.95 7.53556 3.45 8.6323 3.95 7.6 4.45 7.6 4.95 7.6"
-compatible_printers_condition = nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Verbatim BVOH @MMU2 0.25]
-inherits = Verbatim BVOH @MMU2
-filament_max_volumetric_speed = 2
-filament_minimal_purge_on_wipe_tower = 10
-filament_ramming_parameters = "200 110 1.74194 1.90323 2.16129 2.48387 2.83871 3.25806 3.83871 4.6129 5.41935 5.96774| 0.05 1.69677 0.45 1.96128 0.95 2.63872 1.45 3.46129 1.95 4.99031 2.45 6.12908 2.95 8.30974 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
-compatible_printers_condition = nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:PrimaSelect PVA+ @MMU2 0.25]
-inherits = PrimaSelect PVA+ @MMU2
-filament_max_volumetric_speed = 2
-filament_minimal_purge_on_wipe_tower = 10
-filament_ramming_parameters = "200 110 2.32258 2.48387 2.67742 2.87097 3.03226 3.22581 3.48387 3.80645 4.29032 5 5.93548 7 7.90323 8.48387 8.80645 8.90323| 0.05 2.27741 0.45 2.54192 0.95 2.9613 1.45 3.33225 1.95 4.02257 2.45 5.48393 2.95 7.72915 3.45 8.76139 3.95 8.95485 4.45 7.6 4.95 7.6"
-compatible_printers_condition = nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Generic HIPS @MMU2]
-inherits = *ABS MMU2*
-filament_vendor = Generic
-filament_cost = 27.3
-filament_density = 1.04
-fan_always_on = 1
-first_layer_temperature = 230
-first_layer_bed_temperature = 100
-temperature = 230
-bed_temperature = 110
-cooling = 1
-min_fan_speed = 20
-max_fan_speed = 20
-bridge_fan_speed = 50
-min_print_speed = 15
-slowdown_below_layer_time = 20
-disable_fan_first_layers = 3
-filament_cooling_final_speed = 2 
-filament_cooling_initial_speed = 3
-filament_cooling_moves = 1
-filament_type = HIPS
-filament_soluble = 1
-filament_colour = #FFFFD7
-filament_ramming_parameters = "130 120 2.74194 2.96774 3.25806 3.77419 4.83871 6.3871 8.09677 9.64516 10.7419 11.2903| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 7.13871 1.95 10.2806 2.45 11.4194 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.03{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-
-[filament:Prusament ASA @MMU2]
-inherits = *ABS MMU2*
-filament_vendor = Prusa Polymers
-filament_cost = 42.69
-filament_density = 1.07
-filament_spool_weight = 201
-fan_always_on = 1
-first_layer_temperature = 260
-first_layer_bed_temperature = 105
-temperature = 260
-bed_temperature = 110
-cooling = 1
-min_fan_speed = 20
-max_fan_speed = 20
-bridge_fan_speed = 30
-min_print_speed = 15
-slowdown_below_layer_time = 15
-disable_fan_first_layers = 4
-filament_cooling_final_speed = 2 
-filament_cooling_initial_speed = 3
-filament_cooling_moves = 1
-filament_type = ASA
-filament_colour = #FFF2EC
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-
-[filament:Prusament PC Blend @MMU2]
-inherits = *ABS MMU2*
-filament_vendor = Prusa Polymers
-filament_cost = 62.36
-filament_density = 1.22
-filament_spool_weight = 201
-fan_always_on = 0
-fan_below_layer_time = 30
-first_layer_temperature = 265
-first_layer_bed_temperature = 105
-temperature = 265
-bed_temperature = 110
-cooling = 1
-min_fan_speed = 20
-max_fan_speed = 20
-bridge_fan_speed = 30
-min_print_speed = 15
-slowdown_below_layer_time = 20
-disable_fan_first_layers = 4
-filament_cooling_final_speed = 2 
-filament_cooling_initial_speed = 3
-filament_cooling_moves = 1
-filament_max_volumetric_speed = 8
-filament_retract_lift = 0.2
-filament_ramming_parameters = "130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
-filament_type = PC
-filament_colour = #DEE0E6
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.07{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K22{elsif nozzle_diameter[0]==0.8};{else}M900 K40{endif} ; Filament gcode LA 1.0"
-
-[filament:Prusament PC Blend Carbon Fiber @MMU2]
-inherits = Prusament PC Blend @MMU2
-filament_cost = 90.73
-filament_density = 1.16
-extrusion_multiplier = 1.04
-fan_below_layer_time = 10
-first_layer_temperature = 280
-temperature = 280
-disable_fan_first_layers = 4
-filament_retract_lift = nil
-filament_colour = #BBBBBB
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and nozzle_diameter[0]!=0.8 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Prusa ABS @MMU2]
-inherits = *ABS MMU2*
-filament_vendor = Made for Prusa
-filament_cost = 27.82
-filament_spool_weight = 230
-
-[filament:Filament PM ABS @MMU2]
-inherits = *ABS MMU2*
-renamed_from = "Plasty Mladec ABS @MMU2"
-filament_vendor = Filament PM
-filament_density = 1.08
-filament_cost = 27.82
-filament_spool_weight = 230
-
-[filament:Prusa HIPS]
-inherits = *ABS*
-filament_vendor = Made for Prusa
-filament_cost = 27.3
-filament_density = 1.04
-filament_spool_weight = 230
-bridge_fan_speed = 50
-cooling = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 10
-filament_colour = #FFFFD7
-filament_soluble = 1
-filament_type = HIPS
-first_layer_temperature = 220
-max_fan_speed = 20
-min_fan_speed = 20
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.03{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-temperature = 220
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Generic HIPS]
-inherits = *ABS*
-filament_vendor = Generic
-filament_cost = 27.3
-filament_density = 1.04
-bridge_fan_speed = 50
-cooling = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 10
-filament_colour = #FFFFD7
-filament_soluble = 1
-filament_type = HIPS
-first_layer_temperature = 230
-max_fan_speed = 20
-min_fan_speed = 20
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.03{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-temperature = 230
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Prusa PETG]
-inherits = *PET*
-renamed_from = "Prusa PET"
-filament_vendor = Made for Prusa
-filament_cost = 27.82
-filament_density = 1.27
-filament_spool_weight = 230
-compatible_printers_condition = nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Verbatim PETG]
-inherits = *PET*
-filament_vendor = Verbatim
-filament_cost = 27.90
-filament_density = 1.27
-filament_spool_weight = 235
-compatible_printers_condition = nozzle_diameter[0]!=0.6 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Prusament PETG]
-inherits = *PET*
-filament_vendor = Prusa Polymers
-first_layer_temperature = 240
-temperature = 250
-filament_cost = 36.29
-filament_density = 1.27
-filament_spool_weight = 201
-filament_type = PETG
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.6 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Prusa PETG @0.6 nozzle]
-inherits = *PET06*
-renamed_from = "Prusa PET 0.6 nozzle"; "Prusa PETG 0.6 nozzle"
-filament_vendor = Made for Prusa
-filament_cost = 27.82
-filament_density = 1.27
-filament_spool_weight = 230
-
-[filament:Prusament PETG @0.6 nozzle]
-inherits = *PET06*
-filament_vendor = Prusa Polymers
-first_layer_temperature = 240
-temperature = 250
-filament_cost = 36.29
-filament_density = 1.27
-filament_spool_weight = 201
-filament_type = PETG
-
-[filament:Filament PM PETG @0.6 nozzle]
-inherits = *PET06*
-renamed_from = "Plasty Mladec PETG @0.6 nozzle"
-filament_vendor = Filament PM
-first_layer_temperature = 230
-temperature = 240
-filament_cost = 27.82
-filament_density = 1.27
-filament_spool_weight = 230
-filament_type = PETG
-
-[filament:Devil Design PETG @0.6 nozzle]
-inherits = *PET06*
-filament_vendor = Devil Design
-first_layer_temperature = 230
-first_layer_bed_temperature = 85
-temperature = 230
-bed_temperature = 90
-filament_cost = 20.99
-filament_density = 1.23
-filament_spool_weight = 250
-filament_type = PETG
-
-[filament:Verbatim PETG @0.6 nozzle]
-inherits = *PET06*
-filament_vendor = Verbatim
-first_layer_temperature = 230
-temperature = 240
-filament_cost = 27.90
-filament_density = 1.27
-filament_spool_weight = 235
-filament_type = PETG
-
-[filament:Fiberlogy Easy PET-G @0.6 nozzle]
-inherits = *PET06*
-renamed_from = Fiberlogy PETG @0.6 nozzle
-filament_vendor = Fiberlogy
-first_layer_temperature = 230
-temperature = 240
-filament_cost = 21.50
-filament_density = 1.27
-filament_type = PETG
-
-[filament:*PET MMU2*]
-inherits = Prusa PETG
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-temperature = 230
-first_layer_temperature = 230
-filament_cooling_final_speed = 1
-filament_cooling_initial_speed = 2
-filament_cooling_moves = 1
-filament_load_time = 15
-filament_loading_speed = 14
-filament_ramming_parameters = "120 140 4.70968 4.74194 4.77419 4.80645 4.83871 4.87097 4.90323 5 5.25806 5.67742 6.29032 7.06452 7.83871 8.3871| 0.05 4.72901 0.45 4.73545 0.95 4.83226 1.45 4.88067 1.95 5.05483 2.45 5.93553 2.95 7.53556 3.45 8.6323 3.95 7.6 4.45 7.6 4.95 7.6"
-filament_unload_time = 12
-filament_unloading_speed = 20
-filament_unloading_speed_start = 120
-filament_loading_speed_start = 19
-filament_retract_length = 1
-filament_retract_lift = 0.2
-filament_max_volumetric_speed = 7
-
-[filament:*PET MMU2 06*]
-inherits = *PET MMU2*
-compatible_printers_condition = nozzle_diameter[0]==0.6 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-filament_max_volumetric_speed = 13
-
-[filament:Generic PETG @MMU2]
-inherits = *PET MMU2*
-renamed_from = "Generic PET MMU2"; "Generic PETG MMU2"
-filament_vendor = Generic
-
-[filament:Filament PM PETG @MMU2]
-inherits = *PET MMU2*
-renamed_from = "Plasty Mladec PETG @MMU2"
-filament_vendor = Filament PM
-filament_spool_weight = 230
-
-[filament:Prusa PETG @MMU2]
-inherits = *PET MMU2*
-renamed_from = "Prusa PET MMU2"; "Prusa PETG MMU2"
-filament_vendor = Made for Prusa
-filament_cost = 27.82
-filament_spool_weight = 230
-
-[filament:Prusament PETG @MMU2]
-inherits = *PET MMU2*
-filament_type = PETG
-filament_vendor = Prusa Polymers
-filament_cost = 36.29
-filament_density = 1.27
-filament_spool_weight = 201
-
-[filament:Generic PETG @MMU2 0.6 nozzle]
-inherits = *PET MMU2 06*
-renamed_from = "Generic PET MMU2 0.6 nozzle"; "Generic PETG MMU2 0.6 nozzle"
-filament_vendor = Generic
-
-[filament:Prusa PETG @MMU2 0.6 nozzle]
-inherits = *PET MMU2 06*
-renamed_from = "Prusa PET MMU2 0.6 nozzle"; "Prusa PETG MMU2 0.6 nozzle"
-filament_vendor = Made for Prusa
-filament_spool_weight = 230
-
-[filament:Prusament PETG @MMU2 0.6 nozzle]
-inherits = *PET MMU2 06*
-filament_type = PETG
-filament_vendor = Prusa Polymers
-filament_cost = 36.29
-filament_density = 1.27
-filament_spool_weight = 201
-
-[filament:Filament PM PETG @MMU2 0.6 nozzle]
-inherits = *PET MMU2 06*
-renamed_from = "Plasty Mladec PETG @MMU2 0.6 nozzle"
-filament_type = PETG
-filament_vendor = Filament PM
-filament_spool_weight = 230
-
-[filament:Prusa PLA]
-inherits = *PLA*
-filament_vendor = Made for Prusa
-filament_cost = 27.82
-filament_density = 1.24
-filament_spool_weight = 230
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Fiberlogy Easy PLA]
-inherits = *PLA*
-renamed_from = Fiberlogy PLA
-filament_vendor = Fiberlogy
-filament_cost = 20
-filament_density = 1.24
-first_layer_temperature = 220
-temperature = 220
-filament_spool_weight = 330
-
-[filament:Fiberlogy Easy PET-G]
-inherits = *PET*
-renamed_from = Fiberlogy PETG
-filament_vendor = Fiberlogy
-filament_spool_weight = 330
-filament_cost = 20
-filament_density = 1.27
-compatible_printers_condition = nozzle_diameter[0]!=0.6 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-first_layer_bed_temperature = 80
-bed_temperature = 80
-first_layer_temperature = 235
-temperature = 235
-min_fan_speed = 15
-max_fan_speed = 30
-bridge_fan_speed = 60
-disable_fan_first_layers = 5
-full_fan_speed_layer = 5
-slowdown_below_layer_time = 15
-
-[filament:Fiberlogy ASA]
-inherits = *ABS*
-filament_vendor = Fiberlogy
-filament_cost = 33
-filament_density = 1.07
-filament_spool_weight = 330
-fan_always_on = 0
-cooling = 1
-min_fan_speed = 10
-max_fan_speed = 15
-bridge_fan_speed = 30
-min_print_speed = 15
-slowdown_below_layer_time = 15
-first_layer_temperature = 260
-temperature = 260
-first_layer_bed_temperature = 105
-bed_temperature = 110
-filament_type = ASA
-fan_below_layer_time = 30
-disable_fan_first_layers = 5
-
-[filament:Fiberlogy ASA @MINI]
-inherits = Fiberlogy ASA; *ABSMINI*
-
-[filament:Fiberlogy Easy ABS]
-inherits = Fiberlogy ASA
-filament_cost = 22.67
-filament_density = 1.09
-fan_always_on = 0
-cooling = 1
-min_fan_speed = 10
-max_fan_speed = 15
-min_print_speed = 15
-slowdown_below_layer_time = 15
-first_layer_temperature = 250
-temperature = 250
-first_layer_bed_temperature = 100
-bed_temperature = 100
-filament_type = ABS
-fan_below_layer_time = 25
-disable_fan_first_layers = 5
-
-[filament:Fiberlogy Easy ABS @MINI]
-inherits = Fiberlogy Easy ABS; *ABSMINI*
-
-[filament:Fiberlogy CPE HT]
-inherits = *PET*
-filament_vendor = Fiberlogy
-filament_cost = 42.67
-filament_density = 1.18
-extrusion_multiplier = 0.98
-filament_spool_weight = 330
-fan_always_on = 1
-cooling = 1
-min_fan_speed = 0
-max_fan_speed = 0
-bridge_fan_speed = 50
-min_print_speed = 15
-first_layer_temperature = 275
-temperature = 275
-first_layer_bed_temperature = 105
-bed_temperature = 110
-filament_type = CPE
-fan_below_layer_time = 20
-slowdown_below_layer_time = 15
-disable_fan_first_layers = 5
-
-[filament:Fiberlogy PCTG]
-inherits = Fiberlogy CPE HT
-filament_vendor = Fiberlogy
-filament_cost = 29.41
-filament_density = 1.23
-extrusion_multiplier = 0.98
-min_fan_speed = 10
-max_fan_speed = 15
-bridge_fan_speed = 50
-min_print_speed = 15
-first_layer_temperature = 265
-temperature = 265
-first_layer_bed_temperature = 90
-bed_temperature = 90
-filament_type = CPE
-fan_below_layer_time = 20
-slowdown_below_layer_time = 15
-disable_fan_first_layers = 5
-
-[filament:Fiberlogy FiberFlex 40D]
-inherits = *FLEX*
-filament_vendor = Fiberlogy
-fan_always_on = 1
-filament_max_volumetric_speed = 1.5
-extrusion_multiplier = 1.12
-first_layer_temperature = 230
-first_layer_bed_temperature = 60
-temperature = 230
-bed_temperature = 60
-bridge_fan_speed = 75
-min_fan_speed = 25
-max_fan_speed = 75
-filament_retract_before_travel = 2
-filament_cost = 39.41
-filament_density = 1.16
-filament_retract_length = 1.2
-filament_retract_speed = nil
-filament_deretract_speed = 20
-filament_retract_lift = 0
-filament_wipe = 0
-disable_fan_first_layers = 5
-full_fan_speed_layer = 5
-min_print_speed = 15
-cooling = 1
-filament_spool_weight = 330
-
-[filament:Fiberlogy FiberFlex 40D @MINI]
-inherits = *FLEXMINI*
-filament_vendor = Fiberlogy
-filament_max_volumetric_speed = 1.5
-fan_always_on = 1
-first_layer_temperature = 240
-first_layer_bed_temperature = 60
-temperature = 240
-bed_temperature = 60
-filament_retract_length = 4
-filament_retract_before_travel = 5
-bridge_fan_speed = 80
-min_fan_speed = 25
-max_fan_speed = 60
-min_print_speed = 15
-slowdown_below_layer_time = 10
-cooling = 1
-filament_cost = 84.68
-
-[filament:Fiberlogy MattFlex 40D]
-inherits = Fiberlogy FiberFlex 40D
-filament_vendor = Fiberlogy
-fan_always_on = 1
-filament_max_volumetric_speed = 1.35
-extrusion_multiplier = 1.1
-filament_retract_before_travel = 2
-filament_cost = 49.11
-filament_retract_length = 1.2
-
-[filament:Fiberlogy FiberFlex 30D]
-inherits = Fiberlogy FiberFlex 40D
-filament_max_volumetric_speed = 1.2
-extrusion_multiplier = 1.15
-first_layer_temperature = 240
-temperature = 240
-min_fan_speed = 25
-max_fan_speed = 60
-filament_density = 1.07
-filament_retract_length = 1.2
-
-[filament:Fiberlogy FiberSatin]
-inherits = Fiberlogy Easy PLA
-first_layer_temperature = 215
-temperature = 215
-extrusion_multiplier = 1.03
-filament_density = 1.2
-filament_cost = 32.35
-
-[filament:Fiberlogy FiberSilk]
-inherits = Fiberlogy FiberSatin
-first_layer_temperature = 230
-temperature = 230
-extrusion_multiplier = 0.97
-filament_density = 1.22
-filament_cost = 32.35
-
-[filament:Fiberlogy FiberWood]
-inherits = Fiberlogy Easy PLA
-first_layer_temperature = 185
-temperature = 185
-extrusion_multiplier = 1
-filament_density = 1.23
-filament_cost = 38.66
-filament_max_volumetric_speed = 8
-
-[filament:Fiberlogy HD PLA]
-inherits = Fiberlogy Easy PLA
-first_layer_temperature = 230
-temperature = 230
-extrusion_multiplier = 1
-filament_density = 1.24
-filament_cost = 30.59
-
-[filament:Fiberlogy PLA Mineral]
-inherits = Fiberlogy Easy PLA
-first_layer_temperature = 195
-temperature = 190
-extrusion_multiplier = 0.98
-filament_density = 1.38
-filament_cost = 37.64
-filament_max_volumetric_speed = 10
-
-[filament:Fiberlogy Impact PLA]
-inherits = Fiberlogy HD PLA
-filament_density = 1.22
-filament_cost = 27.65
-
-[filament:Fiberlogy Nylon PA12]
-inherits = Fiberlogy ASA
-filament_type = PA
-filament_density = 1.01
-filament_cost = 48
-first_layer_bed_temperature = 105
-bed_temperature = 110
-first_layer_temperature = 265
-temperature = 265
-min_fan_speed = 10
-max_fan_speed = 15
-fan_below_layer_time = 20
-bridge_fan_speed = 30
-fan_always_on = 0
-filament_retract_lift = 0.2
-filament_max_volumetric_speed = 6
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.08{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K26{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
-
-[filament:Fiberlogy Nylon PA12+CF15]
-inherits = Fiberlogy Nylon PA12
-extrusion_multiplier = 0.97
-filament_density = 1.07
-filament_cost = 87.5
-first_layer_bed_temperature = 105
-bed_temperature = 110
-first_layer_temperature = 265
-temperature = 265
-min_fan_speed = 10
-max_fan_speed = 15
-fan_below_layer_time = 20
-bridge_fan_speed = 30
-fan_always_on = 0
-filament_max_volumetric_speed = 8
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Fiberlogy Nylon PA12+GF15]
-inherits = Fiberlogy Nylon PA12+CF15
-filament_density = 1.13
-filament_max_volumetric_speed = 8
-
-[filament:Fiberlogy PP]
-inherits = *ABS*
-filament_vendor = Fiberlogy
-filament_cost = 36.67
-filament_density = 1.05
-extrusion_multiplier = 1.05
-filament_spool_weight = 330
-fan_always_on = 1
-cooling = 1
-min_fan_speed = 0
-max_fan_speed = 25
-bridge_fan_speed = 70
-min_print_speed = 15
-slowdown_below_layer_time = 15
-first_layer_temperature = 245
-temperature = 245
-first_layer_bed_temperature = 0
-bed_temperature = 0
-filament_type = PP
-fan_below_layer_time = 100
-disable_fan_first_layers = 5
-filament_max_volumetric_speed = 5
-
-[filament:Filament PM PLA]
-inherits = *PLA*
-renamed_from = "Plasty Mladec PLA"
-filament_vendor = Filament PM
-filament_cost = 27.82
-filament_density = 1.24
-filament_spool_weight = 230
-
-[filament:AmazonBasics PLA]
-inherits = *PLA*
-filament_vendor = AmazonBasics
-filament_cost = 25.4
-filament_density = 1.24
-
-[filament:Overture PLA]
-inherits = *PLA*
-filament_vendor = Overture
-filament_cost = 22
-filament_density = 1.24
-filament_spool_weight = 235
-
-[filament:Hatchbox PLA]
-inherits = *PLA*
-filament_vendor = Hatchbox
-filament_cost = 25.4
-filament_density = 1.27
-filament_spool_weight = 245
-
-[filament:Esun PLA]
-inherits = *PLA*
-filament_vendor = Esun
-filament_cost = 25.4
-filament_density = 1.24
-filament_spool_weight = 265
-
-[filament:Das Filament PLA]
-inherits = *PLA*
-filament_vendor = Das Filament
-filament_cost = 25.4
-filament_density = 1.24
-
-[filament:EUMAKERS PLA]
-inherits = *PLA*
-filament_vendor = EUMAKERS
-filament_cost = 25.4
-filament_density = 1.24
-
-[filament:Floreon3D PLA]
-inherits = *PLA*
-filament_vendor = Floreon3D
-filament_cost = 25.4
-filament_density = 1.24
-
-[filament:Prusament PLA]
-inherits = *PLA*
-filament_vendor = Prusa Polymers
-temperature = 215
-filament_cost = 36.29
-filament_density = 1.24
-filament_spool_weight = 201
-filament_notes = "Affordable filament for everyday printing in premium quality manufactured in-house by Josef Prusa"
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Prusament PVB]
-inherits = *PLA*
-filament_vendor = Prusa Polymers
-temperature = 215
-bed_temperature = 75
-first_layer_bed_temperature = 75
-filament_cost = 60.48
-filament_density = 1.09
-filament_spool_weight = 201
-filament_max_volumetric_speed = 8
-filament_type = PVB
-filament_soluble = 1
-filament_colour = #FFFF6F
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-slowdown_below_layer_time = 20
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.05{else}0.08{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
-
-[filament:*PLA MMU2*]
-inherits = Prusa PLA
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-temperature = 205
-filament_cooling_final_speed = 2
-filament_cooling_initial_speed = 3
-filament_cooling_moves = 1
-filament_load_time = 15
-filament_loading_speed = 14
-filament_ramming_parameters = "130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
-filament_unload_time = 12
-filament_unloading_speed = 20
-filament_loading_speed_start = 19
-filament_minimal_purge_on_wipe_tower = 15
-filament_unloading_speed_start = 100
-full_fan_speed_layer = 4
-filament_max_volumetric_speed = 13
-
-[filament:Generic PLA @MMU2]
-inherits = *PLA MMU2*
-filament_vendor = Generic
-
-[filament:Prusa PLA @MMU2]
-inherits = *PLA MMU2*
-filament_vendor = Made for Prusa
-filament_cost = 27.82
-filament_spool_weight = 230
-
-[filament:Prusament PLA @MMU2]
-inherits = *PLA MMU2*
-filament_vendor = Prusa Polymers
-filament_cost = 36.29
-filament_density = 1.24
-filament_spool_weight = 201
-
-[filament:Prusament PVB @MMU2]
-inherits = *PLA MMU2*
-filament_vendor = Prusa Polymers
-filament_cost = 60.48
-filament_density = 1.09
-filament_max_volumetric_speed = 8
-filament_soluble = 1
-filament_type = PVB
-filament_colour = #FFFF6F
-filament_spool_weight = 201
-slowdown_below_layer_time = 20
-filament_ramming_parameters = "120 110 1.74194 1.90323 2.16129 2.48387 2.83871 3.25806 3.83871 4.6129 5.41935 5.96774| 0.05 1.69677 0.45 1.96128 0.95 2.63872 1.45 3.46129 1.95 4.99031 2.45 6.12908 2.95 8.30974 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.05{else}0.08{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
-
-[filament:Fillamentum PLA @MMU2]
-inherits = *PLA MMU2*
-filament_vendor = Fillamentum
-filament_cost = 35.48
-filament_density = 1.24
-filament_spool_weight = 230
-
-[filament:SemiFlex]
-inherits = *FLEX*
-renamed_from = "SemiFlex or Flexfill 98A"
-filament_vendor = Generic
-filament_cost = 82.26
-filament_density = 1.22
-extrusion_multiplier = 1.12
-filament_max_volumetric_speed = 1.35
-fan_always_on = 1
-cooling = 0
-max_fan_speed = 30
-min_fan_speed = 30
-filament_retract_length = nil
-
-[filament:Fillamentum Flexfill 98A]
-inherits = *FLEX*
-filament_vendor = Fillamentum
-filament_cost = 82.26
-filament_density = 1.23
-filament_spool_weight = 230
-extrusion_multiplier = 1.12
-filament_max_volumetric_speed = 1.35
-fan_always_on = 1
-cooling = 0
-max_fan_speed = 60
-min_fan_speed = 60
-disable_fan_first_layers = 4
-full_fan_speed_layer = 6
-filament_retract_length = 1.2
-filament_deretract_speed = 20
-
-[filament:Taulman Bridge]
-inherits = *common*
-filament_vendor = Taulman
-filament_cost = 40
-filament_density = 1.13
-bed_temperature = 110
-bridge_fan_speed = 40
-cooling = 0
-disable_fan_first_layers = 3
-fan_always_on = 0
-fan_below_layer_time = 20
-filament_colour = #DEE0E6
-filament_max_volumetric_speed = 7
-filament_soluble = 0
-filament_type = PA
-first_layer_bed_temperature = 90
-first_layer_temperature = 260
-temperature = 260
-max_fan_speed = 0
-min_fan_speed = 0
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.08{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
-compatible_printers_condition = printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Taulman Bridge @MINI]
-inherits = Taulman Bridge
-bed_temperature = 90
-first_layer_bed_temperature = 60
-first_layer_temperature = 240
-temperature = 250
-compatible_printers_condition = printer_model=="MINI"
-
-[filament:Fillamentum Nylon FX256]
-inherits = *common*
-filament_vendor = Fillamentum
-filament_cost = 56.99
-filament_density = 1.01
-filament_spool_weight = 230
-bed_temperature = 90
-bridge_fan_speed = 30
-cooling = 1
-disable_fan_first_layers = 6
-fan_always_on = 0
-fan_below_layer_time = 20
-min_print_speed = 15
-slowdown_below_layer_time = 20
-filament_colour = #DEE0E6
-filament_max_volumetric_speed = 6
-filament_soluble = 0
-filament_type = PA
-first_layer_bed_temperature = 90
-first_layer_temperature = 250
-max_fan_speed = 0
-min_fan_speed = 0
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.05{else}0.1{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K28{elsif nozzle_diameter[0]==0.8};{else}M900 K48{endif} ; Filament gcode LA 1.0"
-temperature = 250
-
-[filament:Fiberthree F3 PA Pure Pro]
-inherits = *common*
-filament_vendor = Fiberthree
-filament_cost = 200.84
-filament_density = 1.2
-bed_temperature = 90
-first_layer_bed_temperature = 90
-first_layer_temperature = 285
-temperature = 285
-bridge_fan_speed = 30
-cooling = 1
-disable_fan_first_layers = 3
-fan_always_on = 1
-fan_below_layer_time = 20
-min_print_speed = 15
-slowdown_below_layer_time = 10
-filament_colour = #DEE0E6
-filament_max_volumetric_speed = 5
-filament_soluble = 0
-filament_type = PA
-max_fan_speed = 20
-min_fan_speed = 20
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0"
-filament_retract_length = 2
-filament_retract_speed = 40
-filament_retract_lift = nil
-filament_retract_before_travel = 1.5
-filament_wipe = 0
-compatible_printers_condition = printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Fiberthree F3 PA-CF Pro]
-inherits = *common*
-filament_vendor = Fiberthree
-filament_cost = 208.1
-filament_density = 1.25
-bed_temperature = 90
-first_layer_bed_temperature = 90
-first_layer_temperature = 285
-temperature = 285
-bridge_fan_speed = 30
-cooling = 1
-disable_fan_first_layers = 3
-fan_always_on = 0
-fan_below_layer_time = 20
-min_print_speed = 15
-slowdown_below_layer_time = 10
-filament_colour = #DEE0E6
-filament_max_volumetric_speed = 5
-filament_soluble = 0
-filament_type = PA
-max_fan_speed = 0
-min_fan_speed = 0
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0"
-filament_retract_length = 2
-filament_retract_speed = 40
-filament_retract_lift = nil
-filament_retract_before_travel = 1.5
-filament_wipe = 0
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Fiberthree F3 PA-GF Pro]
-inherits = Fiberthree F3 PA-CF Pro
-filament_vendor = Fiberthree
-filament_cost = 205.68
-filament_density = 1.27
-fan_always_on = 1
-max_fan_speed = 15
-min_fan_speed = 15
-
-[filament:Taulman T-Glase]
-inherits = *PET*
-filament_vendor = Taulman
-filament_cost = 40
-filament_density = 1.27
-bridge_fan_speed = 40
-cooling = 0
-fan_always_on = 0
-first_layer_bed_temperature = 90
-first_layer_temperature = 240
-max_fan_speed = 5
-min_fan_speed = 0
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.08{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
-
-[filament:Verbatim PLA]
-inherits = *PLA*
-filament_vendor = Verbatim
-filament_cost = 42.99
-filament_density = 1.24
-filament_spool_weight = 235
-
-[filament:Verbatim BVOH]
-inherits = *common*
-filament_vendor = Verbatim
-filament_cost = 193.58
-filament_density = 1.14
-filament_spool_weight = 235
-bed_temperature = 60
-bridge_fan_speed = 100
-cooling = 0
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 100
-filament_colour = #FFFFD7
-filament_max_volumetric_speed = 4
-filament_soluble = 1
-filament_type = PVA
-first_layer_bed_temperature = 60
-first_layer_temperature = 215
-max_fan_speed = 100
-min_fan_speed = 100
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-temperature = 210
-
-[filament:Verbatim BVOH @MMU2]
-inherits = Verbatim BVOH
-filament_vendor = Verbatim
-compatible_printers_condition = nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-temperature = 195
-fan_always_on = 1
-first_layer_temperature = 200
-filament_cooling_final_speed = 1
-filament_cooling_initial_speed = 2
-filament_max_volumetric_speed = 4
-filament_type = PVA
-filament_cooling_moves = 1
-filament_load_time = 15
-filament_loading_speed = 14
-filament_ramming_parameters = "120 110 1.74194 1.90323 2.16129 2.48387 2.83871 3.25806 3.83871 4.6129 5.41935 5.96774| 0.05 1.69677 0.45 1.96128 0.95 2.63872 1.45 3.46129 1.95 4.99031 2.45 6.12908 2.95 8.30974 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
-filament_unload_time = 12
-filament_unloading_speed = 20
-filament_unloading_speed_start = 100
-filament_loading_speed_start = 19
-
-[filament:PrimaSelect PVA+ @MMU2]
-inherits = *common*
-filament_vendor = PrimaSelect
-compatible_printers_condition = nozzle_diameter[0]!=0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-bed_temperature = 60
-bridge_fan_speed = 100
-cooling = 0
-disable_fan_first_layers = 1
-fan_always_on = 0
-fan_below_layer_time = 100
-filament_colour = #FFFFD7
-filament_cooling_final_speed = 2
-filament_cooling_initial_speed = 4
-filament_cooling_moves = 2
-filament_cost = 122.1
-filament_density = 1.24
-filament_diameter = 1.75
-filament_load_time = 15
-filament_loading_speed = 14
-filament_loading_speed_start = 19
-filament_max_volumetric_speed = 3.8
-filament_minimal_purge_on_wipe_tower = 15
-filament_ramming_parameters = "120 110 3.83871 3.90323 3.96774 4.03226 4.09677 4.19355 4.3871 4.83871 5.67742 6.93548 8.54839 10.3226 11.9677 13.2581 14.129 14.5806| 0.05 3.8258 0.45 3.89676 0.95 4.05807 1.45 4.23548 1.95 5.18386 2.45 7.80651 2.95 11.5356 3.45 13.9872 3.95 14.7613 4.45 7.6 4.95 7.6"
-filament_soluble = 1
-filament_toolchange_delay = 0
-filament_type = PVA
-filament_unload_time = 12
-filament_unloading_speed = 20
-filament_unloading_speed_start = 100
-first_layer_bed_temperature = 60
-first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 100
-min_print_speed = 15
-slowdown_below_layer_time = 20
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
-temperature = 195
-
-[filament:Verbatim PP]
-inherits = *common*
-filament_vendor = Verbatim
-filament_cost = 72
-filament_density = 0.89
-filament_spool_weight = 235
-bed_temperature = 100
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 2
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 100
-filament_colour = #DEE0E6
-filament_max_volumetric_speed = 5
-filament_type = PP
-first_layer_bed_temperature = 100
-first_layer_temperature = 220
-max_fan_speed = 100
-min_fan_speed = 100
-start_filament_gcode = "M900 K0 ; Filament gcode"
-temperature = 220
-
-## Filaments MMU1
-
-[filament:ColorFabb HT @MMU1]
-inherits = ColorFabb HT; *PETMMU1*
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
-
-[filament:ColorFabb XT @MMU1]
-inherits = ColorFabb XT; *PETMMU1*
-
-[filament:ColorFabb XT-CF20 @MMU1]
-inherits = ColorFabb XT-CF20; *PETMMU1*
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
-
-[filament:ColorFabb nGen @MMU1]
-inherits = ColorFabb nGen; *PETMMU1*
-
-[filament:E3D Edge @MMU1]
-inherits = E3D Edge; *PETMMU1*
-
-[filament:Fillamentum CPE @MMU1]
-inherits = Fillamentum CPE; *PETMMU1*
-
-[filament:Generic PETG @MMU1]
-inherits = Generic PETG; *PETMMU1*
-renamed_from = "Generic PET MMU1"; "Generic PETG MMU1"
-
-[filament:Devil Design PETG @MMU1]
-inherits = Devil Design PETG; *PETMMU1*
-
-[filament:Filament PM PETG @MMU1]
-inherits = Filament PM PETG; *PETMMU1*
-renamed_from = "Plasty Mladec PETG @MMU1"
-
-[filament:Verbatim PETG @MMU1]
-inherits = Verbatim PETG; *PETMMU1*
-
-[filament:Fiberlogy Easy PET-G @MMU1]
-inherits = Fiberlogy Easy PET-G; *PETMMU1*
-renamed_from = Fiberlogy PETG @MMU1
-
-[filament:Prusa PETG @MMU1]
-inherits = Prusa PETG; *PETMMU1*
-renamed_from = "Prusa PET MMU1"; "Prusa PETG MMU1"
-
-[filament:Prusament PETG @MMU1]
-inherits = Prusament PETG; *PETMMU1*
-
-[filament:Taulman T-Glase @MMU1]
-inherits = Taulman T-Glase; *PETMMU1*
-start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
-
-[filament:Fiberthree F3 PA Pure Pro @MMU1]
-inherits = Fiberthree F3 PA Pure Pro
-filament_max_volumetric_speed = 4
-filament_retract_length = nil
-filament_retract_speed = nil
-filament_retract_lift = nil
-filament_retract_before_travel = nil
-filament_wipe = nil
-compatible_printers_condition = printer_model=="MK2SMM"
-
-[filament:Fiberthree F3 PA-CF Pro @MMU1]
-inherits = Fiberthree F3 PA-CF Pro
-filament_max_volumetric_speed = 4
-filament_retract_length = nil
-filament_retract_speed = nil
-filament_retract_lift = nil
-filament_retract_before_travel = nil
-filament_wipe = nil
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model=="MK2SMM"
-
-[filament:Fiberthree F3 PA-GF Pro @MMU1]
-inherits = Fiberthree F3 PA-CF Pro @MMU1
-filament_vendor = Fiberthree
-filament_cost = 205.68
-filament_density = 1.27
-fan_always_on = 1
-max_fan_speed = 15
-min_fan_speed = 15
-
-[filament:SemiFlex @MMU1]
-inherits = *FLEX*
-renamed_from = "SemiFlex or Flexfill 98A @MMU1"
-filament_vendor = Generic
-filament_cost = 82.26
-filament_density = 1.22
-extrusion_multiplier = 1.12
-filament_max_volumetric_speed = 1.35
-filament_retract_length = nil
-filament_retract_speed = nil
-filament_retract_lift = nil
-compatible_printers_condition = printer_model=="MK2SMM"
-fan_always_on = 1
-cooling = 0
-max_fan_speed = 30
-min_fan_speed = 30
-
-[filament:Generic FLEX @MMU1]
-inherits = *FLEX*
-filament_vendor = Generic
-filament_cost = 82
-filament_density = 1.22
-filament_max_volumetric_speed = 1.2
-filament_retract_length = 0
-filament_retract_speed = nil
-filament_retract_lift = nil
-compatible_printers_condition = printer_model=="MK2SMM"
-
-## Filaments MINI
-
-[filament:Generic PETG @MINI]
-inherits = Generic PETG; *PETMINI*
-renamed_from = "Generic PET MINI"; "Generic PETG MINI"
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.6
-
-[filament:Devil Design PETG @MINI]
-inherits = Devil Design PETG; *PETMINI*
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]!=0.6
-
-[filament:Filament PM PETG @MINI]
-inherits = Filament PM PETG; *PETMINI*
-renamed_from = "Plasty Mladec PETG @MINI"
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]!=0.6
-
-[filament:Verbatim PETG @MINI]
-inherits = Verbatim PETG; *PETMINI*
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]!=0.6
-
-[filament:Fiberlogy Easy PET-G @MINI]
-inherits = Fiberlogy Easy PET-G; *PETMINI*
-renamed_from = Fiberlogy PETG @MINI
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]!=0.6
-
-[filament:Generic ABS @MINI]
-inherits = Generic ABS; *ABSMINI*
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]!=0.8 
-
-[filament:Fiberthree F3 PA Pure Pro @MINI]
-inherits = Fiberthree F3 PA Pure Pro
-filament_max_volumetric_speed = 4
-first_layer_temperature = 280
-temperature = 280
-first_layer_bed_temperature = 75
-bed_temperature = 70
-filament_retract_length = nil
-filament_retract_speed = nil
-filament_retract_lift = nil
-filament_retract_before_travel = nil
-filament_wipe = nil
-compatible_printers_condition = printer_model=="MINI"
-
-[filament:Fiberthree F3 PA-CF Pro @MINI]
-inherits = Fiberthree F3 PA-CF Pro
-first_layer_temperature = 280
-temperature = 280
-first_layer_bed_temperature = 75
-bed_temperature = 70
-filament_max_volumetric_speed = 4
-filament_retract_length = nil
-filament_retract_speed = nil
-filament_retract_lift = nil
-filament_retract_before_travel = nil
-filament_wipe = nil
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model=="MINI"
-
-[filament:Fiberthree F3 PA-GF Pro @MINI]
-inherits = Fiberthree F3 PA-CF Pro @MINI
-filament_vendor = Fiberthree
-filament_cost = 205.68
-filament_density = 1.27
-fan_always_on = 1
-max_fan_speed = 15
-min_fan_speed = 15
-
-[filament:Kimya ABS Carbon @MINI]
-inherits = Kimya ABS Carbon; *ABSMINI*
-filament_max_volumetric_speed = 6
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model=="MINI"
-
-[filament:Kimya ABS Kevlar @MINI]
-inherits = Kimya ABS Carbon @MINI
-filament_vendor = Kimya
-filament_density = 1.037
-
-[filament:Esun ABS @MINI]
-inherits = Esun ABS; *ABSMINI*
-
-[filament:Hatchbox ABS @MINI]
-inherits = Hatchbox ABS; *ABSMINI*
-
-[filament:Filament PM ABS @MINI]
-inherits = Filament PM ABS; *ABSMINI*
-renamed_from = "Plasty Mladec ABS @MINI"
-
-[filament:Verbatim ABS @MINI]
-inherits = Verbatim ABS; *ABSMINI*
-
-[filament:Prusament PETG @MINI]
-inherits = Prusament PETG; *PETMINI*
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.6
-
-[filament:Kimya PETG Carbon @MINI]
-inherits = Kimya PETG Carbon; *PETMINI*
-filament_max_volumetric_speed = 6
-filament_retract_length = nil
-filament_retract_lift = 0.3
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model=="MINI"
-
-[filament:Prusament PETG @0.6 nozzle MINI]
-inherits = Prusament PETG; *PETMINI06*
-
-[filament:Generic PETG @0.6 nozzle MINI]
-inherits = Generic PETG; *PETMINI06*
-renamed_from = "Generic PET 0.6 nozzle MINI"; "Generic PETG 0.6 nozzle MINI"
-
-[filament:Devil Design PETG @0.6 nozzle MINI]
-inherits = Devil Design PETG; *PETMINI06*
-
-[filament:Filament PM PETG @0.6 nozzle MINI]
-inherits = Filament PM PETG; *PETMINI06*
-renamed_from = "Plasty Mladec PETG @0.6 nozzle MINI"
-
-[filament:Verbatim PETG @0.6 nozzle MINI]
-inherits = Verbatim PETG; *PETMINI06*
-
-[filament:Fiberlogy Easy PET-G @0.6 nozzle MINI]
-inherits = Fiberlogy Easy PET-G; *PETMINI06*
-renamed_from = Fiberlogy PETG @0.6 nozzle MINI
-
-[filament:Prusament ASA @MINI]
-inherits = Prusament ASA; *ABSMINI*
-first_layer_bed_temperature = 100
-bed_temperature = 100
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]!=0.8
-
-[filament:Fillamentum Flexfill 98A @MINI]
-inherits = SemiFlex; *FLEXMINI*
-filament_vendor = Fillamentum
-first_layer_temperature = 240
-temperature = 240
-filament_max_volumetric_speed = 1.35
-filament_cost = 82.26
-filament_spool_weight = 230
-max_fan_speed = 60
-min_fan_speed = 60
-
-[filament:Generic FLEX @MINI]
-inherits = SemiFlex; *FLEXMINI*
-filament_vendor = Generic
-fan_always_on = 0
-bridge_fan_speed = 80
-first_layer_temperature = 240
-temperature = 240
-filament_retract_length = 3
-filament_max_volumetric_speed = 1.35
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]!=0.8
- 
-
-[filament:AmazonBasics TPU @MINI]
-inherits = *FLEXMINI*
-filament_vendor = AmazonBasics
-filament_max_volumetric_speed = 1.5
-first_layer_temperature = 235
-first_layer_bed_temperature = 50
-temperature = 235
-bed_temperature = 50
-bridge_fan_speed = 100
-max_fan_speed = 80
-min_fan_speed = 80
-filament_retract_before_travel = 5
-filament_cost = 19.99
-filament_density = 1.21
-
-[filament:SainSmart TPU @MINI]
-inherits = *FLEXMINI*
-filament_vendor = SainSmart
-filament_max_volumetric_speed = 1.8
-first_layer_temperature = 235
-first_layer_bed_temperature = 50
-temperature = 235
-bed_temperature = 50
-bridge_fan_speed = 100
-max_fan_speed = 80
-min_fan_speed = 80
-filament_retract_before_travel = 5
-min_print_speed = 15
-slowdown_below_layer_time = 10
-cooling = 1
-filament_cost = 32.99
-filament_density = 1.21
-
-[filament:Filatech FilaFlex40 @MINI]
-inherits = *FLEXMINI*
-filament_vendor = Filatech
-filament_max_volumetric_speed = 1.8
-fan_always_on = 1
-first_layer_temperature = 240
-first_layer_bed_temperature = 55
-temperature = 240
-bed_temperature = 55
-filament_retract_length = 4
-filament_retract_before_travel = 5
-bridge_fan_speed = 80
-max_fan_speed = 50
-min_fan_speed = 50
-min_print_speed = 15
-slowdown_below_layer_time = 10
-cooling = 1
-filament_cost = 84.68
-
-[filament:Fillamentum Flexfill 92A @MINI]
-inherits = *FLEXMINI*
-filament_vendor = Fillamentum
-first_layer_temperature = 245
-temperature = 245
-filament_retract_length = 3
-filament_retract_speed = 40
-filament_deretract_speed = 15
-filament_retract_lift = 0
-filament_retract_before_travel = 7
-filament_wipe = 0
-filament_density = 1.20
-filament_spool_weight = 230
-filament_cost = 33.95
-bridge_fan_speed = 70
-fan_always_on = 1
-cooling = 0
-max_fan_speed = 60
-min_fan_speed = 60
-filament_max_volumetric_speed = 1.2
-compatible_printers_condition = nozzle_diameter[0]>0.35 and printer_model=="MINI"
-disable_fan_first_layers = 4
-extrusion_multiplier = 1.15
-start_filament_gcode = "M900 K0 ; Filament gcode"
-
-[filament:Fillamentum CPE @MINI]
-inherits = Fillamentum CPE; *PETMINI*
-first_layer_temperature = 265
-first_layer_bed_temperature = 90
-temperature = 265
-disable_fan_first_layers = 3
-full_fan_speed_layer = 5
-
-[filament:ColorFabb nGen @MINI]
-inherits = ColorFabb nGen; *PETMINI*
-
-[filament:E3D PC-ABS @MINI]
-inherits = E3D PC-ABS; *ABSMINI*
-filament_retract_length = nil
-filament_retract_before_travel = nil
-filament_wipe = nil
-
-[filament:Fillamentum ABS @MINI]
-inherits = Fillamentum ABS; *ABSMINI*
-
-[filament:Fillamentum ASA @MINI]
-inherits = Fillamentum ASA; *ABSMINI*
-first_layer_bed_temperature = 100
-bed_temperature = 100
-
-[filament:Polymaker PC-Max @MINI]
-inherits = Polymaker PC-Max; *ABSMINI*
-filament_max_volumetric_speed = 7
-bed_temperature = 100
-first_layer_bed_temperature = 100
-first_layer_temperature = 270
-temperature = 270
-filament_retract_length = nil
-filament_retract_before_travel = nil
-filament_wipe = nil
-
-[filament:Prusament PC Blend @MINI]
-inherits = Prusament PC Blend; *ABSMINI*
-first_layer_temperature = 275
-first_layer_bed_temperature = 100
-temperature = 275
-bed_temperature = 100
-filament_max_volumetric_speed = 7
-filament_retract_length = nil
-filament_retract_speed = nil
-filament_deretract_speed = nil
-filament_retract_lift = nil
-filament_retract_before_travel = nil
-filament_wipe = nil
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]!=0.8
-
-[filament:Prusament PC Blend Carbon Fiber @MINI]
-inherits = Prusament PC Blend @MINI
-filament_cost = 90.73
-filament_density = 1.16
-extrusion_multiplier = 1.04
-first_layer_temperature = 280
-temperature = 280
-disable_fan_first_layers = 4
-fan_below_layer_time = 10
-filament_max_volumetric_speed = 6.5
-filament_colour = #BBBBBB
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]>=0.4 and nozzle_diameter[0]!=0.8
-
-[filament:Prusa ABS @MINI]
-inherits = Prusa ABS; *ABSMINI*
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]!=0.8
-
-[filament:Generic HIPS @MINI]
-inherits = Generic HIPS; *ABSMINI*
-
-[filament:ColorFabb HT @MINI]
-inherits = ColorFabb HT; *PETMINI*
-bed_temperature = 100
-first_layer_bed_temperature = 100
-min_fan_speed = 15
-
-[filament:ColorFabb XT @MINI]
-inherits = ColorFabb XT; *PETMINI*
-first_layer_bed_temperature = 90
-
-[filament:ColorFabb XT-CF20 @MINI]
-inherits = ColorFabb XT-CF20; *PETMINI*
-compatible_printers_condition = nozzle_diameter[0]>=0.4 and printer_model=="MINI"
-first_layer_bed_temperature = 90
-first_layer_temperature = 260
-temperature = 260
-
-[filament:Taulman T-Glase @MINI]
-inherits = Taulman T-Glase; *PETMINI*
-
-[filament:E3D Edge @MINI]
-inherits = E3D Edge; *PETMINI*
-
-[filament:Prusa PETG @MINI]
-inherits = Prusa PETG; *PETMINI*
-renamed_from = "Prusa PET MINI"; "Prusa PETG MINI"
-compatible_printers_condition = printer_model=="MINI" and nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.6
-
-[filament:Prusa PETG @0.6 nozzle MINI]
-inherits = Prusa PETG; *PETMINI06*
-renamed_from = "Prusa PET 0.6 nozzle MINI"; "Prusa PETG 0.6 nozzle MINI"
-
-## Filaments 0.8 nozzle
-
-[filament:Generic PLA @0.8 nozzle]
-inherits = Generic PLA
-first_layer_temperature = 220
-temperature = 220
-filament_max_volumetric_speed = 15
-slowdown_below_layer_time = 20
-compatible_printers_condition = nozzle_diameter[0]==0.8 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Generic ABS @0.8 nozzle]
-inherits = Generic ABS
-first_layer_temperature = 265
-temperature = 265
-filament_max_volumetric_speed = 15
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Generic PETG @0.8 nozzle]
-inherits = Generic PETG
-first_layer_temperature = 240
-temperature = 250
-filament_max_volumetric_speed = 20
-filament_retract_lift = 0.2
-slowdown_below_layer_time = 20
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Prusa PLA @0.8 nozzle]
-inherits = Prusa PLA
-first_layer_temperature = 220
-temperature = 220
-filament_max_volumetric_speed = 15
-slowdown_below_layer_time = 20
-compatible_printers_condition = nozzle_diameter[0]==0.8 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Prusa PETG @0.8 nozzle]
-inherits = Prusa PETG
-first_layer_temperature = 240
-temperature = 250
-filament_max_volumetric_speed = 20
-slowdown_below_layer_time = 20
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Prusa ABS @0.8 nozzle]
-inherits = Prusa ABS
-first_layer_temperature = 265
-temperature = 265
-filament_max_volumetric_speed = 15
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Generic FLEX @0.8 nozzle]
-inherits = Generic FLEX
-filament_max_volumetric_speed = 4.3
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model!="MK2SMM" and printer_model!="MINI" and num_extruders==1 && ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and single_extruder_multi_material)
-
-[filament:Generic HIPS @0.8 nozzle]
-inherits = Generic HIPS
-first_layer_temperature = 240
-temperature = 240
-filament_max_volumetric_speed = 15
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Prusament PLA @0.8 nozzle]
-inherits = Prusament PLA
-first_layer_temperature = 225
-temperature = 225
-filament_max_volumetric_speed = 15
-slowdown_below_layer_time = 20
-compatible_printers_condition = nozzle_diameter[0]==0.8 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Prusament PETG @0.8 nozzle]
-inherits = Prusament PETG
-first_layer_temperature = 250
-temperature = 260
-filament_max_volumetric_speed = 20
-filament_retract_lift = 0.2
-slowdown_below_layer_time = 20
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model!="MK2SMM" and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Prusament ASA @0.8 nozzle]
-inherits = Prusament ASA
-first_layer_temperature = 265
-temperature = 265
-filament_max_volumetric_speed = 15
-slowdown_below_layer_time = 20
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model!="MINI" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-
-[filament:Prusament PC Blend @0.8 nozzle]
-inherits = Prusament PC Blend
-filament_max_volumetric_speed = 13
-filament_retract_lift = 0.25
-compatible_printers_condition = printer_notes!~/.*PRINTER_MODEL_MK(2|2.5).*/ and nozzle_diameter[0]==0.8 and printer_model!="MINI" and ! single_extruder_multi_material
-
-[filament:Prusament PC Blend Carbon Fiber @0.8 nozzle]
-inherits = Prusament PC Blend Carbon Fiber
-filament_max_volumetric_speed = 13
-filament_retract_lift = 0.25
-compatible_printers_condition = printer_notes!~/.*PRINTER_MODEL_MK(2|2.5).*/ and nozzle_diameter[0]==0.8 and printer_model!="MINI" and ! single_extruder_multi_material
-
-[filament:Prusament PA11 Carbon Fiber @0.8 nozzle]
-inherits = Prusament PA11 Carbon Fiber
-filament_max_volumetric_speed = 11
-compatible_printers_condition = printer_notes!~/.*PRINTER_MODEL_MK(2|2.5).*/ and nozzle_diameter[0]==0.8 and printer_model!="MINI" and ! single_extruder_multi_material
-
-[filament:Prusament PA11 Carbon Fiber @0.8 nozzle MK2]
-inherits = Prusament PA11 Carbon Fiber @MK2
-filament_max_volumetric_speed = 11
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model!="MK2SMM" and printer_notes=~/.*PRINTER_MODEL_MK(2|2.5).*/ and ! (printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and single_extruder_multi_material)
-
-[filament:Prusament PC Blend @0.8 nozzle MK2]
-inherits = Prusament PC Blend @MK2
-filament_max_volumetric_speed = 13
-filament_retract_lift = 0.25
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model!="MK2SMM" and printer_notes=~/.*PRINTER_MODEL_MK(2|2.5).*/ and ! (printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and single_extruder_multi_material)
-
-[filament:Prusament PVB @0.8 nozzle]
-inherits = Prusament PVB
-first_layer_temperature = 225
-temperature = 225
-filament_max_volumetric_speed = 15
-compatible_printers_condition = nozzle_diameter[0]==0.8 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
-slowdown_below_layer_time = 20
-
-## Filaments 0.8 nozzle MMU2
-
-[filament:Generic HIPS @MMU2 0.8 nozzle]
-inherits = Generic HIPS @MMU2
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-
-[filament:Prusament ASA @MMU2 0.8 nozzle]
-inherits = Prusament ASA @MMU2
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-slowdown_below_layer_time = 20
-filament_max_volumetric_speed = 14
-
-[filament:Prusament PC Blend @MMU2 0.8 nozzle]
-inherits = Prusament PC Blend @MMU2
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-filament_max_volumetric_speed = 12
-
-[filament:Generic PETG @MMU2 0.8 nozzle]
-inherits = Generic PETG @MMU2
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-filament_max_volumetric_speed = 18
-first_layer_temperature = 240
-temperature = 240
-slowdown_below_layer_time = 20
-filament_ramming_parameters = "120 140 5.51613 5.6129 5.70968 5.77419 5.77419 5.74194 5.80645 5.93548 6.06452 6.19355 6.3871 6.74194 7.25806 7.87097 8.54839 9.22581 10 10.8387| 0.05 5.5032 0.45 5.63868 0.95 5.8 1.45 5.7839 1.95 6.02257 2.45 6.25811 2.95 7.08395 3.45 8.43875 3.95 9.92258 4.45 11.3419 4.95 7.6"
-
-[filament:Prusament PETG @MMU2 0.8 nozzle]
-inherits = Prusament PETG @MMU2
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-filament_max_volumetric_speed = 18
-first_layer_temperature = 240
-temperature = 240
-slowdown_below_layer_time = 20
-filament_ramming_parameters = "120 140 5.51613 5.6129 5.70968 5.77419 5.77419 5.74194 5.80645 5.93548 6.06452 6.19355 6.3871 6.74194 7.25806 7.87097 8.54839 9.22581 10 10.8387| 0.05 5.5032 0.45 5.63868 0.95 5.8 1.45 5.7839 1.95 6.02257 2.45 6.25811 2.95 7.08395 3.45 8.43875 3.95 9.92258 4.45 11.3419 4.95 7.6"
-
-[filament:Generic PLA @MMU2 0.8 nozzle]
-inherits = Generic PLA @MMU2
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-filament_max_volumetric_speed = 14
-first_layer_temperature = 215
-temperature = 210
-
-[filament:Prusament PLA @MMU2 0.8 nozzle]
-inherits = Prusament PLA @MMU2
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-filament_max_volumetric_speed = 14
-first_layer_temperature = 215
-temperature = 210
-
-[filament:Verbatim BVOH @MMU2 0.8 nozzle]
-inherits = Verbatim BVOH @MMU2
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-filament_max_volumetric_speed = 8
-
-[filament:PrimaSelect PVA+ @MMU2 0.8 nozzle]
-inherits = PrimaSelect PVA+ @MMU2
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
-filament_max_volumetric_speed = 8
-
-## Filaments 0.8 nozzle MINI
-
-[filament:Generic ABS @0.8 nozzle MINI]
-inherits = Generic ABS @MINI
-first_layer_temperature = 265
-temperature = 265
-filament_max_volumetric_speed = 13
-filament_retract_length = 3.2
-filament_wipe = nil
-filament_retract_speed = nil
-filament_deretract_speed = nil
-filament_retract_lift = nil
-filament_retract_before_travel = 2
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model=="MINI"
-
-[filament:Generic PETG @0.8 nozzle MINI]
-inherits = Generic PETG @MINI
-first_layer_temperature = 240
-temperature = 250
-filament_max_volumetric_speed = 15
-slowdown_below_layer_time = 20
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model=="MINI"
-
-[filament:Prusa PETG @0.8 nozzle MINI]
-inherits = Prusa PETG @MINI
-first_layer_temperature = 240
-temperature = 250
-filament_max_volumetric_speed = 15
-slowdown_below_layer_time = 20
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model=="MINI"
-
-[filament:Prusa ABS @0.8 nozzle MINI]
-inherits = Prusa ABS @MINI
-first_layer_temperature = 265
-temperature = 265
-filament_max_volumetric_speed = 13
-slowdown_below_layer_time = 20
-filament_retract_length = 3.2
-filament_wipe = nil
-filament_retract_speed = nil
-filament_deretract_speed = nil
-filament_retract_lift = nil
-filament_retract_before_travel = 2
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model=="MINI"
-
-[filament:Generic FLEX @0.8 nozzle MINI]
-inherits = Generic FLEX @MINI
-filament_max_volumetric_speed = 4.3
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model=="MINI"
-
-[filament:Prusament PETG @0.8 nozzle MINI]
-inherits = Prusament PETG @MINI
-first_layer_temperature = 245
-temperature = 255
-filament_max_volumetric_speed = 15
-filament_retract_lift = 0.25
-slowdown_below_layer_time = 20
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model=="MINI"
-
-[filament:Prusament ASA @0.8 nozzle MINI]
-inherits = Prusament ASA @MINI
-first_layer_temperature = 265
-temperature = 265
-filament_max_volumetric_speed = 13
-slowdown_below_layer_time = 20
-filament_retract_length = 3.2
-filament_wipe = nil
-filament_retract_speed = nil
-filament_deretract_speed = nil
-filament_retract_lift = nil
-filament_retract_before_travel = 2
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model=="MINI"
-
-[filament:Prusament PC Blend @0.8 nozzle MINI]
-inherits = Prusament PC Blend @MINI
-filament_max_volumetric_speed = 11
-filament_retract_lift = 0.25
-slowdown_below_layer_time = 20
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model=="MINI"
-
-[filament:Prusament PC Blend Carbon Fiber @0.8 nozzle MINI]
-inherits = Prusament PC Blend Carbon Fiber @MINI
-filament_max_volumetric_speed = 10
-filament_retract_lift = 0.25
-slowdown_below_layer_time = 20
-compatible_printers_condition = nozzle_diameter[0]==0.8 and printer_model=="MINI"
-
-[sla_print:*common*]
-compatible_printers_condition = printer_model=="SL1"
-layer_height = 0.05
-output_filename_format = [input_filename_base].sl1
-pad_edge_radius = 0.5
-pad_enable = 1
-pad_max_merge_distance = 50
-pad_wall_height = 0
-pad_wall_thickness = 1
-pad_wall_slope = 45
-slice_closing_radius = 0.005
-support_base_diameter = 3
-support_base_height = 1
-support_critical_angle = 45
-support_density_at_45 = 250
-support_density_at_horizontal = 500
-support_head_front_diameter = 0.4
-support_head_penetration = 0.4
-support_head_width = 3
-support_max_bridge_length = 10
-support_minimal_z = 0
-support_object_elevation = 5
-support_pillar_diameter = 1
-support_pillar_connection_mode = zigzag
-support_pillar_widening_factor = 0
-supports_enable = 1
-support_small_pillar_diameter_percent = 60%
-
-[sla_print:*SL1S*]
-inherits = *common*
-support_head_front_diameter = 0.5
-support_head_penetration = 0.5
-support_pillar_diameter = 1
-output_filename_format = [input_filename_base].sl1s
-compatible_printers_condition = printer_model=="SL1S"
-
-# SL1 #
-
-[sla_print:0.025 UltraDetail]
-inherits = *common*
-layer_height = 0.025
-support_head_width = 2
-
-[sla_print:0.035 Detail]
-inherits = *common*
-layer_height = 0.035
-
-[sla_print:0.05 Normal]
-inherits = *common*
-layer_height = 0.05
-
-[sla_print:0.1 Fast]
-inherits = *common*
-layer_height = 0.1
-support_head_front_diameter = 0.5
-support_head_penetration = 0.5
-support_pillar_diameter = 1.3
-
-# SL1S #
-
-[sla_print:0.025 UltraDetail @SL1S]
-inherits = *SL1S*
-layer_height = 0.025
-support_head_width = 3
-
-[sla_print:0.05 Normal @SL1S]
-inherits = *SL1S*
-layer_height = 0.05
-
-[sla_print:0.1 Fast @SL1S]
-inherits = *SL1S*
-layer_height = 0.1
-support_head_front_diameter = 0.6
-support_head_penetration = 0.6
-
-########### Materials
-
-[sla_material:*common*]
-compatible_printers_condition = printer_model=="SL1"
-compatible_prints_condition = layer_height == 0.05
-exposure_time = 12
-initial_exposure_time = 45
-initial_layer_height = 0.05
-material_correction = 1,1,1
-material_notes = 
-
-[sla_material:*common 0.025*]
-inherits = *common*
-compatible_prints_condition = layer_height == 0.025
-exposure_time = 10
-initial_exposure_time = 35
-initial_layer_height = 0.025
-
-[sla_material:*common 0.035*]
-inherits = *common*
-compatible_prints_condition = layer_height == 0.035
-exposure_time = 13
-initial_exposure_time = 40
-initial_layer_height = 0.035
-
-[sla_material:*common 0.05*]
-inherits = *common*
-
-[sla_material:*common 0.1*]
-inherits = *common*
-compatible_prints_condition = layer_height == 0.1
-exposure_time = 20
-initial_exposure_time = 45
-initial_layer_height = 0.1
-
-[sla_material:*0.025_sl1s*]
-inherits = *common*
-compatible_prints_condition = layer_height == 0.025
-compatible_printers_condition = printer_model=="SL1S"
-exposure_time = 1.3
-initial_exposure_time = 25
-initial_layer_height = 0.025
-
-[sla_material:*0.05_sl1s*]
-inherits = *common*
-compatible_printers_condition = printer_model=="SL1S"
-exposure_time = 1.7
-initial_exposure_time = 25
-
-[sla_material:*0.1_sl1s*]
-inherits = *common*
-compatible_prints_condition = layer_height == 0.1
-compatible_printers_condition = printer_model=="SL1S"
-exposure_time = 2.6
-initial_exposure_time = 25
-initial_layer_height = 0.1
-
-########### Materials 0.025
-
-[sla_material:3DM-ABS @0.025]
-inherits = *common 0.025*
-exposure_time = 12
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = 3DM
-material_colour = #FF8040
-
-[sla_material:3DM-Vulcan Gold @0.025]
-inherits = *common 0.025*
-exposure_time = 12
-initial_exposure_time = 30
-material_type = Casting
-material_vendor = 3DM
-material_colour = #B0B000
-
-[sla_material:3DM-TOUGH Clear @0.025]
-inherits = *common 0.025*
-exposure_time = 9
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = 3DM
-material_colour = #F8F8F8
-
-[sla_material:3DM-HR Red Wine @0.025]
-inherits = *common 0.025*
-exposure_time = 14
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = 3DM
-material_colour = #EC0000
-
-[sla_material:BlueCast Phrozen Wax @0.025]
-inherits = *common 0.025*
-exposure_time = 15
-initial_exposure_time = 50
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #007EFD
-
-[sla_material:BlueCast Castable Wax @0.025]
-inherits = *common 0.025*
-exposure_time = 8
-initial_exposure_time = 35
-material_type = Casting
-material_vendor = BlueCast
-material_colour = #007EFD
-
-[sla_material:BlueCast EcoGray @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #808080
-
-[sla_material:BlueCast Kera Master Dental @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 45
-material_type = Dental
-material_vendor = BlueCast
-material_colour = #B0B000
-
-[sla_material:BlueCast Model Dental Gray @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Dental
-material_vendor = BlueCast
-material_colour = #C0C0C0
-
-[sla_material:BlueCast X10 @0.025]
-inherits = *common 0.025*
-exposure_time = 4
-initial_exposure_time = 100
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #007EFD
-
-[sla_material:DruckWege Type D High Temp @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 20
-material_type = Tough
-material_vendor = DruckWege
-material_colour = #E800E8
-
-[sla_material:Esun Bio-Photopolymer Resin White @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Esun
-material_colour = #FFFFFF
-
-[sla_material:FunToDo Castable Blend Red @0.025]
-inherits = *common 0.025*
-exposure_time = 10
-initial_exposure_time = 35
-material_type = Casting
-material_vendor = FunToDo
-material_colour = #EC0000
-
-[sla_material:FunToDo Snow White @0.025]
-inherits = *common 0.025*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = FunToDo
-material_colour = #FFFFFF
-
-[sla_material:Harz Labs Basic Resin Red @0.025]
-inherits = *common 0.025*
-exposure_time = 10
-initial_exposure_time = 20
-material_type = Tough
-material_vendor = Harz Labs
-material_colour = #EC0000
-
-[sla_material:Harz Labs Model Resin Cherry @0.025]
-inherits = *common 0.025*
-exposure_time = 10
-initial_exposure_time = 20
-material_type = Tough
-material_vendor = Harz Labs
-material_colour = #EC0000
-
-[sla_material:Harz Labs Model Resin Black @0.025]
-inherits = *common 0.025*
-exposure_time = 10
-initial_exposure_time = 20
-material_type = Tough
-material_vendor = Harz Labs
-material_colour = #595959
-
-[sla_material:Harz Labs Dental Cast Red @0.025]
-inherits = *common 0.025*
-exposure_time = 10
-initial_exposure_time = 20
-material_type = Dental
-material_vendor = Harz Labs
-material_colour = #EC0000
-
-[sla_material:Esun Standard Resin Black @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Esun
-material_colour = #595959
-
-[sla_material:Photocentric Ash Grey @0.025]
-inherits = *common 0.025*
-exposure_time = 9
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Photocentric
-material_colour = #C0C0C0
-
-[sla_material:Resinworks 3D Violet @0.025]
-inherits = *common 0.025*
-exposure_time = 15
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Resinworks 3D
-material_colour = #E800E8
-
-[sla_material:Resinworks 3D Green @0.025]
-inherits = *common 0.025*
-exposure_time = 17
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Resinworks 3D
-material_colour = #00B900
-
-[sla_material:Monocure 3D Black Rapid Resin @0.025]
-inherits = *common 0.025*
-exposure_time = 4
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Monocure
-material_colour = #595959
-
-[sla_material:Monocure 3D Blue Rapid Resin @0.025]
-inherits = *common 0.025*
-exposure_time = 4
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Monocure
-material_colour = #007EFD
-  
-## Prusa Polymers 0.025
-
-[sla_material:Prusament Resin Tough Prusa Orange @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #FF8040
-
-[sla_material:Prusament Resin Tough Rich Black @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #595959
-
-[sla_material:Prusament Resin Tough Anthracite Grey @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #808080
-
-[sla_material:Prusament Resin Tough Sandstone Model @0.025]
-inherits = *common 0.025*
-exposure_time = 4
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #EEA061
-
-[sla_material:Prusament Resin Tough Terra Brown @0.025]
-inherits = *common 0.025*
-exposure_time = 4
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #7A5C45
-
-[sla_material:Prusament Resin Tough Brick Red @0.025]
-inherits = *common 0.025*
-exposure_time = 4
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #B46056
-
-[sla_material:Prusament Resin Tough Grass Green @0.025]
-inherits = *common 0.025*
-exposure_time = 4
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #37823F
-
-[sla_material:Prusament Resin Tough Bright Yellow @0.025]
-inherits = *common 0.025*
-exposure_time = 4
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #F9DB4C
-
-[sla_material:Prusament Resin Tough Transparent Green @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #1DAf5E
-
-[sla_material:Prusament Resin Tough Transparent Red @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #D21B31
-
-[sla_material:Prusament Resin Tough Transparent Amber @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #FCB30E
-
-## Prusa 0.025
-  
-[sla_material:Prusa Orange Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:Prusa Grey Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:Prusa Azure Blue Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-## [sla_material:Prusa Blue Tough @0.025]
-## inherits = *common 0.025*
-## exposure_time = 5
-## initial_exposure_time = 35
-## material_type = Tough
-## material_vendor = Made for Prusa
-
-[sla_material:Prusa Maroon Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #804000
-
-[sla_material:Prusa Beige Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFEEE6
-
-[sla_material:Prusa Pink Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF80C0
-
-[sla_material:Prusa White Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 6.5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFFFF
-
-[sla_material:Prusa Transparent Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 15
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #F8F8F8
-
-[sla_material:Prusa Green Dental Casting @0.025]
-inherits = *common 0.025*
-exposure_time = 12
-initial_exposure_time = 40
-material_type = Casting
-material_vendor = Made for Prusa
-material_colour = #00B900
-
-[sla_material:Prusa Transparent Green Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #00B900
-
-[sla_material:Prusa Clear ABS like @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #F8F8F8
-
-[sla_material:Prusa White ABS like @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFFFF
-
-[sla_material:Prusa Grey High Tenacity @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #C0C0C0
-
-[sla_material:Prusa Super Low Odor Cyan Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #79FFFF
-
-[sla_material:Prusa Super Low Odor Magenta Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #E800E8
-
-[sla_material:Prusa Super Low Odor Yellow Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFF6F
-
-[sla_material:Prusa Orange-Yellow Teeth Model @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFF6F
-
-[sla_material:Prusa Vibrant Orange Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:Prusa Rich Black Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #595959
-
-[sla_material:Prusa Deep Blue Transparent Tough @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #F8F8F8
-
-[sla_material:Prusa Yellow Jewelry Casting @0.025]
-inherits = *common 0.025*
-exposure_time = 8
-initial_exposure_time = 45
-material_type = Casting
-material_vendor = Made for Prusa
-material_colour = #FFFF6F
-
-[sla_material:Ameralabs TGM-7 LED @0.025]
-inherits = *common 0.025*
-exposure_time = 4
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Ameralabs
-material_colour = #C0C0C0
-
-[sla_material:PrimaCreator Tough Light Grey @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #C0C0C0
-
-[sla_material:PrimaCreator Tough Clear @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:PrimaCreator Tough White @0.025]
-inherits = *common 0.025*
-exposure_time = 5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #FFFFFF
-
-[sla_material:PrimaCreator Flex Clear @0.025]
-inherits = *common 0.025*
-exposure_time = 4.5
-initial_exposure_time = 30
-material_type = Flexible
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Simple Clear @0.025]
-inherits = *common 0.025*
-exposure_time = 8
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Blu Clear V2 @0.025]
-inherits = *common 0.025*
-exposure_time = 9
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Blu Blue @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #007EFD
-
-[sla_material:Siraya Tech Fast Grey @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #C0C0C0
-
-[sla_material:Siraya Tech Tenacious @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Easy @0.025]
-inherits = *common 0.025*
-exposure_time = 11
-initial_exposure_time = 15
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Sculpt @0.025]
-inherits = *common 0.025*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #C0C0C0
-
-[sla_material:Siraya Tech Fast Black @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #007EFD
-
-[sla_material:NextDent Model 2.0 Grey @0.025]
-inherits = *common 0.025*
-exposure_time = 14
-initial_exposure_time = 35
-material_type = Dental
-material_vendor = NextDent
-material_colour = #808080
-
-[sla_material:NextDent Surgical Guide @0.025]
-inherits = *common 0.025*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Dental
-material_vendor = NextDent
-material_colour = #FF8040
-
-[sla_material:NextDent Cast Purple @0.025]
-inherits = *common 0.025*
-exposure_time = 7
-initial_exposure_time = 20
-material_type = Casting
-material_vendor = NextDent
-material_colour = #E800E8
-
-[sla_material:MakerJuice Labs Standard Red @0.025]
-inherits = *common 0.025*
-exposure_time = 9
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = MakerJuice Labs
-material_colour = #EC0000
-
-[sla_material:3DJake High Precision Grey @0.025]
-inherits = *common 0.025*
-exposure_time = 8.5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = 3DJake
-material_colour = #C0C0C0
-
-[sla_material:3DJake High Precision Blue @0.025]
-inherits = *common 0.025*
-exposure_time = 6.5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = 3DJake
-material_colour = #007EFD
-
-[sla_material:Zortrax Black @0.025]
-inherits = *common 0.025*
-exposure_time = 4
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Zortrax
-material_colour = #595959
-
-########### Materials 0.05
-
-[sla_material:Asiga Denta Model @0.05]
-inherits = *common 0.05*
-exposure_time = 15
-initial_exposure_time = 30
-material_type = Dental
-material_vendor = Asiga
-material_colour = #FFEEE6
-
-[sla_material:Asiga PlasGRAY @0.05]
-inherits = *common 0.05*
-exposure_time = 29
-initial_exposure_time = 60
-material_type = Tough
-material_vendor = Asiga
-material_colour = #C0C0C0
-
-[sla_material:Ameralabs TGM-7 LED @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Ameralabs
-material_colour = #C0C0C0
-
-[sla_material:Ameralabs AMD 3 LED @0.05]
-inherits = *common 0.05*
-exposure_time = 5
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Ameralabs
-material_colour = #808080
-
-[sla_material:BlueCast EcoGray @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #808080
-
-[sla_material:BlueCast Kera Master Dental @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 50
-material_type = Dental
-material_vendor = BlueCast
-material_colour = #FFEEE6
-
-[sla_material:BlueCast Model Dental Gray @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 35
-material_type = Dental
-material_vendor = BlueCast
-material_colour = #C0C0C0
-
-[sla_material:BlueCast LCD-DLP Original @0.05]
-inherits = *common 0.05*
-exposure_time = 10
-initial_exposure_time = 60
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #007EFD
-
-[sla_material:BlueCast Phrozen Wax @0.05]
-inherits = *common 0.05*
-exposure_time = 16
-initial_exposure_time = 50
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #007EFD
-
-[sla_material:BlueCast Castable Wax @0.05]
-inherits = *common 0.05*
-exposure_time = 11
-initial_exposure_time = 35
-material_type = Casting
-material_vendor = BlueCast
-material_colour = #E800E8
-
-[sla_material:BlueCast S+ @0.05]
-inherits = *common 0.05*
-exposure_time = 9
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #00B900
-
-[sla_material:BlueCast X5 @0.05]
-inherits = *common 0.05*
-exposure_time = 9
-initial_exposure_time = 100
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #007EFD
-
-[sla_material:BlueCast X10 @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 100
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #007EFD
-
-[sla_material:BlueCast 23LS @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 50
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #007EFD
-
-[sla_material:DruckWege Type D High Temp @0.05]
-inherits = *common 0.05*
-exposure_time = 10
-initial_exposure_time = 20
-material_type = Tough
-material_vendor = DruckWege
-material_colour = #E800E8
-
-[sla_material:Monocure 3D Black Rapid Resin @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Monocure
-material_colour = #595959
-
-[sla_material:Monocure 3D Blue Rapid Resin @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Monocure
-material_colour = #007EFD
-
-[sla_material:Monocure 3D Clear Rapid Resin @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = Monocure
-material_colour = #F8F8F8
-
-[sla_material:Monocure 3D Grey Rapid Resin @0.05]
-inherits = *common 0.05*
-exposure_time = 10
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Monocure
-material_colour = #C0C0C0
-
-[sla_material:Monocure 3D White Rapid Resin @0.05]
-inherits = *common 0.05*
-exposure_time = 10
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Monocure
-material_colour = #FFFFFF
-
-[sla_material:3DM-HTR140 (high temperature) @0.05]
-inherits = *common 0.05*
-exposure_time = 12
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = 3DM
-material_colour = #EC0000
-
-[sla_material:Esun Bio-Photopolymer Resin White @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Esun
-material_colour = #FFFFFF
-
-[sla_material:Esun Standard Resin Black @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Esun
-material_colour = #595959
-
-[sla_material:FunToDo Castable Blend Red @0.05]
-inherits = *common 0.05*
-exposure_time = 15
-initial_exposure_time = 35
-material_type = Casting
-material_vendor = FunToDo
-material_colour = #EC0000
-
-[sla_material:FunToDo Industrial Blend Unpigmented @0.05]
-inherits = *common 0.05*
-exposure_time = 4
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = FunToDo
-material_colour = #F8F8F8
-
-[sla_material:FunToDo Snow White @0.05]
-inherits = *common 0.05*
-exposure_time = 10
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = FunToDo
-material_colour = #FFFFFF
-
-[sla_material:3DM-ABS @0.05]
-inherits = *common 0.05*
-exposure_time = 13
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = 3DM
-material_colour = #FF8040
-
-[sla_material:3DM-BLACK @0.05]
-inherits = *common 0.05*
-exposure_time = 20
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = 3DM
-material_colour = #595959
-
-[sla_material:3DM-DENT @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 45
-material_type = Dental
-material_vendor = 3DM
-material_colour = #FFEEE6
-
-[sla_material:3DM-HR Green @0.05]
-inherits = *common 0.05*
-exposure_time = 15
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = 3DM
-material_colour = #00B900
-
-[sla_material:3DM-HR Red Wine @0.05]
-inherits = *common 0.05*
-exposure_time = 18
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = 3DM
-material_colour = #EC0000
-
-[sla_material:3DM-XPRO White @0.05]
-inherits = *common 0.05*
-exposure_time = 9
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = 3DM
-material_colour = #FFFFFF
-
-[sla_material:3DM-Vulcan Gold @0.05]
-inherits = *common 0.05*
-exposure_time = 15
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = 3DM
-material_colour = #B0B000
-
-[sla_material:3DM-TOUGH Clear @0.05]
-inherits = *common 0.05*
-exposure_time = 15
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = 3DM
-material_colour = #F8F8F8
-
-[sla_material:FunToDo Ash Grey @0.05]
-inherits = *common 0.05*
-exposure_time = 9
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = FunToDo
-material_colour = #808080
-
-[sla_material:Harz Labs Model Resin Cherry @0.05]
-inherits = *common 0.05*
-exposure_time = 13
-initial_exposure_time = 20
-material_type = Tough
-material_vendor = Harz Labs
-material_colour = #EC0000
-
-[sla_material:Harz Labs Basic Resin Red @0.05]
-inherits = *common 0.05*
-exposure_time = 13
-initial_exposure_time = 20
-material_type = Tough
-material_vendor = Harz Labs
-material_colour = #EC0000
-
-[sla_material:Harz Labs Model Resin Black @0.05]
-inherits = *common 0.05*
-exposure_time = 13
-initial_exposure_time = 20
-material_type = Tough
-material_vendor = Harz Labs
-material_colour = #595959
-
-[sla_material:Harz Labs Dental Cast Red @0.05]
-inherits = *common 0.05*
-exposure_time = 13
-initial_exposure_time = 20
-material_type = Dental
-material_vendor = Harz Labs
-material_colour = #EC0000
-
-[sla_material:Resinworks 3D Violet @0.05]
-inherits = *common 0.05*
-exposure_time = 17
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Resinworks 3D
-material_colour = #E800E8
-
-[sla_material:Resinworks 3D Green @0.05]
-inherits = *common 0.05*
-exposure_time = 21
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Resinworks 3D
-material_colour = #00B900
-
-[sla_material:Photocentric Hard Grey @0.05]
-inherits = *common 0.05*
-exposure_time = 15
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Photocentric
-material_colour = #808080
-
-[sla_material:Photocentric Ash Grey @0.05]
-inherits = *common 0.05*
-exposure_time = 10
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Photocentric
-material_colour = #C0C0C0
-
-[sla_material:PrimaCreator Tough Light Grey @0.05]
-inherits = *common 0.05*
-exposure_time = 8.5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #C0C0C0
-
-[sla_material:PrimaCreator Tough Clear @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:PrimaCreator Tough White @0.05]
-inherits = *common 0.05*
-exposure_time = 7.5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #FFFFFF
-
-[sla_material:PrimaCreator Flex Clear @0.05]
-inherits = *common 0.05*
-exposure_time = 6.5
-initial_exposure_time = 30
-material_type = Flexible
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Simple Clear @0.05]
-inherits = *common 0.05*
-exposure_time = 10
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Blu Clear V2 @0.05]
-inherits = *common 0.05*
-exposure_time = 10
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Blu Blue @0.05]
-inherits = *common 0.05*
-exposure_time = 12
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #007EFD
-
-[sla_material:Siraya Tech Fast Grey @0.05]
-inherits = *common 0.05*
-exposure_time = 10
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #C0C0C0
-
-[sla_material:Siraya Tech Tenacious @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Easy @0.05]
-inherits = *common 0.05*
-exposure_time = 12
-initial_exposure_time = 15
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Sculpt @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #C0C0C0
-
-[sla_material:Siraya Tech Fast Black @0.05]
-inherits = *common 0.05*
-exposure_time = 9
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #595959
-
-[sla_material:NextDent Model 2.0 Grey @0.05]
-inherits = *common 0.05*
-exposure_time = 12
-initial_exposure_time = 35
-material_type = Dental
-material_vendor = NextDent
-material_colour = #C0C0C0
-
-[sla_material:NextDent Surgical Guide @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Dental
-material_vendor = NextDent
-material_colour = #FFEEE6
-
-[sla_material:NextDent Cast Purple @0.05]
-inherits = *common 0.05*
-exposure_time = 9
-initial_exposure_time = 20
-material_type = Casting
-material_vendor = NextDent
-material_colour = #E800E8
-
-[sla_material:NextDent Crown Bridge @0.05]
-inherits = *common 0.05*
-exposure_time = 11
-initial_exposure_time = 35
-material_type = Dental
-material_vendor = NextDent
-material_colour = #FFFFFF
-
-[sla_material:MakerJuice Labs Standard Red @0.05]
-inherits = *common 0.05*
-exposure_time = 10
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = MakerJuice Labs
-material_colour = #EC0000
-
-[sla_material:3DJake High Precision Grey @0.05]
-inherits = *common 0.05*
-exposure_time = 9
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = 3DJake
-material_colour = #C0C0C0
-
-[sla_material:3DJake High Precision Blue @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = 3DJake
-material_colour = #007EFD
-
-[sla_material:Dragon Resin Metalshine Metal Grey @0.05]
-inherits = *common 0.05*
-exposure_time = 30
-initial_exposure_time = 50
-material_type = Tough
-material_vendor = Dragon Resin
-material_colour = #808080
-
-[sla_material:Dragon Resin Metalshine Dark Brass @0.05]
-inherits = *common 0.05*
-exposure_time = 30
-initial_exposure_time = 50
-material_type = Tough
-material_vendor = Dragon Resin
-material_colour = #B0B000
-
-[sla_material:Dragon Resin Metalshine Brass @0.05]
-inherits = *common 0.05*
-exposure_time = 30
-initial_exposure_time = 50
-material_type = Tough
-material_vendor = Dragon Resin
-material_colour = #B0B000
-
-[sla_material:Zortrax Black @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Zortrax
-material_colour = #595959
-
-## Prusa Polymers 0.05
-
-[sla_material:Prusament Resin Tough Prusa Orange @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #FF8040
-
-[sla_material:Prusament Resin Tough Rich Black @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #595959
-
-[sla_material:Prusament Resin Tough Anthracite Grey @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #C0C0C0
-
-[sla_material:Prusament Resin Tough Sandstone Model @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #EEA061
-
-[sla_material:Prusament Resin Tough Terra Brown @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #7A5C45
-
-[sla_material:Prusament Resin Tough Brick Red @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #B46056
-
-[sla_material:Prusament Resin Tough Grass Green @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #37823F
-
-[sla_material:Prusament Resin Tough Bright Yellow @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #F9DB4C
-
-[sla_material:Prusament Resin Tough Transparent Green @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #1DAf5E
-
-[sla_material:Prusament Resin Tough Transparent Red @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #D21B31
-
-[sla_material:Prusament Resin Tough Transparent Amber @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #FCB30E
-
-## Prusa 0.05
-
-[sla_material:Prusa Beige Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour =
-
-[sla_material:Prusa Orange Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 7.5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:Prusa Grey Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 8.5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #808080
-
-[sla_material:Prusa Black Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #595959
-
-## [sla_material:Prusa Super Low Odor Beige Tough @0.05]
-## inherits = *common 0.05*
-## exposure_time = 7.5
-## initial_exposure_time = 35
-## material_type = Tough
-## material_vendor = Made for Prusa
-
-## [sla_material:Prusa Super Low Odor White Tough @0.05]
-## inherits = *common 0.05*
-## exposure_time = 6.5
-## initial_exposure_time = 35
-## material_type = Tough
-## material_vendor = Made for Prusa
-
-## [sla_material:Prusa Super Low Odor Grey Tough @0.05]
-## inherits = *common 0.05*
-## exposure_time = 6.5
-## initial_exposure_time = 35
-## material_type = Tough
-## material_vendor = Made for Prusa
-
-[sla_material:Prusa Super Low Odor Cyan Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #79FFFF
-
-[sla_material:Prusa Super Low Odor Magenta Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #E800E8
-
-[sla_material:Prusa Super Low Odor Yellow Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFF6F
-
-## [sla_material:Prusa Black High Tenacity @0.05]
-## inherits = *common 0.05*
-## exposure_time = 7
-## initial_exposure_time = 35
-## material_type = Tough
-## material_vendor = Made for Prusa
-
-[sla_material:Prusa Orange-Yellow Teeth Model @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFF6F
-
-[sla_material:Prusa Green Dental Casting @0.05]
-inherits = *common 0.05*
-exposure_time = 13
-initial_exposure_time = 50
-material_type = Casting
-material_vendor = Made for Prusa
-material_colour = #00B900
-
-## [sla_material:Prusa Yellow Solid @0.05]
-## inherits = *common 0.05*
-## exposure_time = 7
-## initial_exposure_time = 35
-
-[sla_material:Prusa White Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 7.5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFFFF
-
-[sla_material:Prusa Transparent Green Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #00B900
-
-[sla_material:Prusa Transparent Red Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #EC0000
-
-[sla_material:Prusa Maroon Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 7.5
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #804000
-
-[sla_material:Prusa Pink Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF80C0
-
-[sla_material:Prusa Azure Blue Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-## [sla_material:Prusa Blue Tough @0.05]
-## inherits = *common 0.05*
-## exposure_time = 8
-## initial_exposure_time = 35
-## material_type = Tough
-## material_vendor = Made for Prusa
-
-[sla_material:Prusa Transparent Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 15
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #F8F8F8
-
-## [sla_material:Prusa Yellow Flexible @0.05]
-## inherits = *common 0.05*
-## exposure_time = 9
-## initial_exposure_time = 35
-
-[sla_material:Prusa Transparent Flexible @0.05]
-inherits = *common 0.05*
-exposure_time = 5
-initial_exposure_time = 15
-material_type = Flexible
-material_vendor = Made for Prusa
-material_colour = #F8F8F8
-
-## [sla_material:Prusa White Flexible @0.05]
-## inherits = *common 0.05*
-## exposure_time = 9
-## initial_exposure_time = 35
-
-[sla_material:Prusa Blue Flexible @0.05]
-inherits = *common 0.05*
-exposure_time = 5
-initial_exposure_time = 15
-material_type = Flexible
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-## [sla_material:Prusa Black Flexible @0.05]
-## inherits = *common 0.05*
-## exposure_time = 9
-## initial_exposure_time = 35
-
-## [sla_material:Prusa Red Flexible @0.05]
-## inherits = *common 0.05*
-## exposure_time = 9
-## initial_exposure_time = 35
-
-[sla_material:Prusa Clear ABS like @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #F8F8F8
-
-[sla_material:Prusa White ABS like @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFFFF
-
-[sla_material:Prusa Yellow Jewelry Casting @0.05]
-inherits = *common 0.05*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Casting
-material_vendor = Made for Prusa
-material_colour = #FFFF6F
-
-[sla_material:Prusa Grey High Tenacity @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 30
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #C0C0C0
-
-[sla_material:Prusa Vibrant Orange Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:Prusa Rich Black Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #595959
-
-[sla_material:Prusa Deep Blue Transparent Tough @0.05]
-inherits = *common 0.05*
-exposure_time = 8
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-########### Materials 0.035
-
-[sla_material:Prusa Orange Tough @0.035]
-inherits = *common 0.035*
-exposure_time = 6
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-########### Materials 0.1
-
-[sla_material:BlueCast EcoGray @0.1]
-inherits = *common 0.1*
-exposure_time = 10
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #C0C0C0
-
-[sla_material:BlueCast Kera Master Dental @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 50
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #FFEEE6
-
-[sla_material:Ameralabs TGM-7 LED @0.1]
-inherits = *common 0.1*
-exposure_time = 10
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Ameralabs
-material_colour = #C0C0C0
-
-## Prusa Polymers 0.1
-
-[sla_material:Prusament Resin Tough Prusa Orange @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #FF8040
-
-[sla_material:Prusament Resin Tough Rich Black @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #595959
-
-[sla_material:Prusament Resin Tough Anthracite Grey @0.1]
-inherits = *common 0.1*
-exposure_time = 14
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #808080
-
-[sla_material:Prusament Resin Tough Sandstone Model @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #EEA061
-
-[sla_material:Prusament Resin Tough Terra Brown @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #7A5C45
-
-[sla_material:Prusament Resin Tough Brick Red @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #B46056
-
-[sla_material:Prusament Resin Tough Grass Green @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #37823F
-
-[sla_material:Prusament Resin Tough Bright Yellow @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #F9DB4C
-
-[sla_material:Prusament Resin Tough Transparent Green @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #1DAf5E
-
-[sla_material:Prusament Resin Tough Transparent Red @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #D21B31
-
-[sla_material:Prusament Resin Tough Transparent Amber @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #FCB30E
-
-## Prusa 0.1
-
-[sla_material:Prusa Orange Tough @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:Prusa Beige Tough @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFEEE6
-
-[sla_material:Prusa Pink Tough @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF80C0
-
-[sla_material:Prusa Azure Blue Tough @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-[sla_material:Prusa Maroon Tough @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #804000
-
-[sla_material:Prusa White Tough @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFFFF
-
-[sla_material:Prusa Black Tough @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 55
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #595959
-
-[sla_material:Prusa Transparent Tough @0.1]
-inherits = *common 0.1*
-exposure_time = 8
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #F8F8F8
-
-[sla_material:Prusa Green Dental Casting @0.1]
-inherits = *common 0.1*
-exposure_time = 15
-initial_exposure_time = 50
-material_type = Casting
-material_vendor = Made for Prusa
-material_colour = #00B900
-
-[sla_material:Prusa Transparent Green Tough @0.1]
-inherits = *common 0.1*
-exposure_time = 7
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #00B900
-
-[sla_material:Prusa Vibrant Orange Tough @0.1]
-inherits = *common 0.1*
-exposure_time = 8
-initial_exposure_time = 35
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:PrimaCreator Tough Light Grey @0.1]
-inherits = *common 0.1*
-exposure_time = 14
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #C0C0C0
-
-[sla_material:PrimaCreator Tough Clear @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:PrimaCreator Tough White @0.1]
-inherits = *common 0.1*
-exposure_time = 13
-initial_exposure_time = 45
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #FFFFFF
-
-[sla_material:PrimaCreator Flex Clear @0.1]
-inherits = *common 0.1*
-exposure_time = 12
-initial_exposure_time = 35
-material_type = Flexible
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-## SL1S materials ##
-
-## 0.025 SL1S
-
-## Prusa Polymers 0.025
-
-[sla_material:Prusament Resin Tough Prusa Orange @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #FF8040
-
-[sla_material:Prusament Resin Tough Rich Black @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #595959
-
-[sla_material:Prusament Resin Tough Anthracite Grey @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #808080
-
-[sla_material:Prusament Resin Tough Sandstone Model @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #EEA061
-
-[sla_material:Prusament Resin Tough Terra Brown @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #7A5C45
-
-[sla_material:Prusament Resin Tough Brick Red @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #B46056
-
-[sla_material:Prusament Resin Tough Grass Green @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #37823F
-
-[sla_material:Prusament Resin Tough Bright Yellow @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #F9DB4C
-
-[sla_material:Prusament Resin Tough Transparent Green @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #1DAf5E
-
-[sla_material:Prusament Resin Tough Transparent Red @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #D21B31
-
-[sla_material:Prusament Resin Tough Transparent Amber @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #FCB30E
-
-## Made for Prusa 0.025
-
-[sla_material:Prusa Orange Tough @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:Prusa White ABS like @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFFFF
-
-[sla_material:Prusa Azure Blue Tough @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-[sla_material:Prusa Black Tough @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #595959
-
-[sla_material:Prusa Cyan Tough @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #79FFFF
-
-[sla_material:Prusa Magenta Tough @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #E800E8
-
-[sla_material:Prusa Maroon Tough @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #804000
-
-[sla_material:Prusa White Tough @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFFFF
-
-[sla_material:Prusa Pink Tough @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF80C0
-
-[sla_material:Prusa Grey Tough @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #C0C0C0
-
-[sla_material:Prusa Blue Flexible @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Flexible
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-[sla_material:Prusa Grey High Tenacity @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #C0C0C0
-
-[sla_material:Prusa Vibrant Orange Tough @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 4
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:Prusa Deep Blue Transparent Tough @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 4
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-[sla_material:Prusa Green Dental Casting @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 3
-initial_exposure_time = 50
-material_type = Casting
-material_vendor = Made for Prusa
-material_colour = #00B900
-
-[sla_material:Ameralabs TGM-7 LED @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Ameralabs
-material_colour = #C0C0C0
-material_print_speed = slow
-
-[sla_material:BASF Ultracur3D RG 35 @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 4
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #FFEEE6
-
-[sla_material:BASF Ultracur3D ST 45 @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 2.5
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:BASF Ultracur3D ST 45 M @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 2.5
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:BASF Ultracur3D ST 80 @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 4.5
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #FFEEE6
-
-[sla_material:BASF Ultracur3D ST 80 White @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 4.5
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #FFFFFF
-
-[sla_material:BASF Ultracur3D ST 80 Black @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 4.5
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:BASF Ultracur3D EL 150 Black @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Flexible
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:BASF Ultracur3D FL 300 Black @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Flexible
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:PrimaCreator Tough Light Grey @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #C0C0C0
-
-[sla_material:PrimaCreator Tough Clear @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:PrimaCreator Tough White @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #FFFFFF
-
-[sla_material:PrimaCreator Flex Clear @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Flexible
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:PrimaCreator Water Washable Transparent @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:DruckWege Type D Dental Model @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.2
-initial_exposure_time = 15
-material_type = Dental
-material_vendor = DruckWege
-material_colour = #FFEEE6
-material_print_speed = slow
-
-[sla_material:DruckWege Type D Standard White @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.6
-initial_exposure_time = 15
-material_type = Tough
-material_vendor = DruckWege
-material_colour = #FFFFFF
-material_print_speed = slow
-
-[sla_material:DruckWege Type D Standard Pigmentfrei Clear @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 15
-material_type = Tough
-material_vendor = DruckWege
-material_colour = #F8F8F8
-material_print_speed = slow
-
-[sla_material:3DM-ABS Orange @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = 3DM
-material_colour = #FF8040
-
-[sla_material:3DM-TOUGH Clear @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = 3DM
-material_colour = #F8F8F8
-
-[sla_material:Peopoly Deft White @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Peopoly
-material_colour = #FFFFFF
-
-[sla_material:Peopoly Neo Clear @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Peopoly
-material_colour = #F8F8F8
-
-[sla_material:Liqcreate Clear Impact @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 7
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = Liqcreate
-material_colour = #F8F8F8
-
-[sla_material:Liqcreate Strong X @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 7
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = Liqcreate
-material_colour = #C0C0C0
-
-[sla_material:Resinworks 3D Green @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 5
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Resinworks 3D
-material_colour = #00B900
-
-[sla_material:3DJake Blue @0.025 SL1S]
-inherits = *0.025_sl1s*
-exposure_time = 1.8
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = 3DJake
-material_colour = #007EFD
-
-## 0.05 SL1S
-
-## Prusa Polymers 0.05
-
-[sla_material:Prusament Resin Tough Prusa Orange @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #FF8040
-
-[sla_material:Prusament Resin Tough Rich Black @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #595959
-
-[sla_material:Prusament Resin Tough Anthracite Grey @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.4
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #808080
-
-[sla_material:Prusament Resin Tough Sandstone Model @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.4
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #EEA061
-
-[sla_material:Prusament Resin Tough Terra Brown @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #7A5C45
-
-[sla_material:Prusament Resin Tough Brick Red @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #B46056
-
-[sla_material:Prusament Resin Tough Grass Green @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #37823F
-
-[sla_material:Prusament Resin Tough Bright Yellow @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #F9DB4C
-
-[sla_material:Prusament Resin Tough Transparent Green @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #1DAf5E
-
-[sla_material:Prusament Resin Tough Transparent Red @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #D21B31
-
-[sla_material:Prusament Resin Tough Transparent Amber @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #FCB30E
-
-## Made for Prusa 0.05
-
-[sla_material:Prusa Orange Tough @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:Prusa White ABS like @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFFFF
-
-[sla_material:Prusa Azure Blue Tough @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-[sla_material:Prusa Black Tough @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.4
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #595959
-
-[sla_material:Prusa Cyan Tough @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #79FFFF
-
-[sla_material:Prusa Magenta Tough @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #E800E8
-
-[sla_material:Prusa Maroon Tough @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.4
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #804000
-
-[sla_material:Prusa White Tough @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFFFF
-
-[sla_material:Prusa Pink Tough @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF80C0
-
-[sla_material:Prusa Blue Flexible @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Flexible
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-[sla_material:Prusa Grey Tough @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.4
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #C0C0C0
-
-[sla_material:Prusa Grey High Tenacity @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #C0C0C0
-
-[sla_material:Prusa Vibrant Orange Tough @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 5
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:Prusa Deep Blue Transparent Tough @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 5
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-[sla_material:Prusa Green Dental Casting @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 4
-initial_exposure_time = 50
-material_type = Casting
-material_vendor = Made for Prusa
-material_colour = #00B900
-
-[sla_material:Ameralabs TGM-7 LED @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Ameralabs
-material_colour = #C0C0C0
-material_print_speed = slow
-
-[sla_material:BASF Ultracur3D RG 35 @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 4.5
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #FFEEE6
-
-[sla_material:BASF Ultracur3D ST 45 @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:BASF Ultracur3D ST 45 M @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:BASF Ultracur3D ST 80 @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 5.5
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #FFEEE6
-
-[sla_material:BASF Ultracur3D ST 80 White @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 5.9
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #FFFFFF
-
-[sla_material:BASF Ultracur3D ST 80 Black @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 5.9
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:BASF Ultracur3D EL 150 Black @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3.8
-initial_exposure_time = 25
-material_type = Flexible
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:BASF Ultracur3D FL 300 Black @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 4.8
-initial_exposure_time = 25
-material_type = Flexible
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:PrimaCreator Tough Light Grey @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.4
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #C0C0C0
-
-[sla_material:PrimaCreator Tough Clear @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:PrimaCreator Tough White @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #FFFFFF
-
-[sla_material:PrimaCreator Flex Clear @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Flexible
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:PrimaCreator Water Washable Transparent @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:DruckWege Type D Dental Model @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 1.4
-initial_exposure_time = 15
-material_type = Dental
-material_vendor = DruckWege
-material_colour = #FFEEE6
-material_print_speed = slow
-
-[sla_material:DruckWege Type D Standard White @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 15
-material_type = Tough
-material_vendor = DruckWege
-material_colour = #FFFFFF
-material_print_speed = slow
-
-[sla_material:DruckWege Type D Standard Pigmentfrei Clear @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 15
-material_type = Tough
-material_vendor = DruckWege
-material_colour = #F8F8F8
-material_print_speed = slow
-
-[sla_material:3DM-ABS Orange @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = 3DM
-material_colour = #FF8040
-
-[sla_material:3DM-TOUGH Clear @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = 3DM
-material_colour = #F8F8F8
-
-[sla_material:Peopoly Deft White @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Peopoly
-material_colour = #FFFFFF
-
-[sla_material:Peopoly Neo Clear @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Peopoly
-material_colour = #F8F8F8
-
-[sla_material:3DM-ABS @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = 3DM
-material_colour = #FF8040
-
-[sla_material:3DM-DENT @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.3
-initial_exposure_time = 36
-material_type = Dental
-material_vendor = 3DM
-material_colour = #FFEEE6
-
-[sla_material:3DM-HR Green @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 5
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = 3DM
-material_colour = #00B900
-
-[sla_material:3DM-HR Red Wine @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 6
-initial_exposure_time = 32
-material_type = Tough
-material_vendor = 3DM
-material_colour = #EC0000
-
-[sla_material:3DM-Vulcan Gold @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 5
-initial_exposure_time = 24
-material_type = Casting
-material_vendor = 3DM
-material_colour = #B0B000
-
-[sla_material:3DM-XPRO White @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = 3DM
-material_colour = #FFFFFF
-
-[sla_material:Asiga Denta Model @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 5
-initial_exposure_time = 24
-material_type = Dental
-material_vendor = Asiga
-material_colour = #FFEEE6
-
-[sla_material:Asiga PlasGRAY @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 9.7
-initial_exposure_time = 48
-material_type = Tough
-material_vendor = Asiga
-material_colour = #C0C0C0
-
-[sla_material:BlueCast EcoGray @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.3
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #808080
-
-[sla_material:BlueCast Phrozen Wax @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 5.3
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = BlueCast
-material_colour = #007EFD
-
-[sla_material:NextDent Model 2.0 Grey @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 4
-initial_exposure_time = 28
-material_type = Dental
-material_vendor = NextDent
-material_colour = #C0C0C0
-
-[sla_material:NextDent Cast Purple @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3
-initial_exposure_time = 16
-material_type = Casting
-material_vendor = NextDent
-material_colour = #E800E8
-
-[sla_material:Siraya Tech Tenacious @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.7
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Blu Clear V2 @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3.3
-initial_exposure_time = 24
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Blu Blue @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 4
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #007EFD
-
-[sla_material:Siraya Tech Fast Black @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #595959
-
-[sla_material:Siraya Tech Fast Grey @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3.3
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #C0C0C0
-
-[sla_material:Siraya Tech Simple Clear @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3.3
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #F8F8F8
-
-[sla_material:Siraya Tech Sculpt @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.7
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = Siraya Tech
-material_colour = #C0C0C0
-
-[sla_material:Harz Labs Model Resin Cherry @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 4.3
-initial_exposure_time = 16
-material_type = Tough
-material_vendor = Harz Labs
-material_colour = #EC0000
-
-[sla_material:Harz Labs Model Resin Black @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 4.3
-initial_exposure_time = 16
-material_type = Tough
-material_vendor = Harz Labs
-material_colour = #595959
-
-[sla_material:Harz Labs Basic Resin Red @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 4.3
-initial_exposure_time = 16
-material_type = Tough
-material_vendor = Harz Labs
-material_colour = #EC0000
-
-[sla_material:Resinworks 3D Violet @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 5.7
-initial_exposure_time = 24
-material_type = Tough
-material_vendor = Resinworks 3D
-material_colour = #E800E8
-
-[sla_material:FunToDo Industrial Blend Unpigmented @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 1.3
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = FunToDo
-material_colour = #F8F8F8
-
-[sla_material:FunToDo Snow White @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3.3
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = FunToDo
-material_colour = #FFFFFF
-
-[sla_material:FunToDo Ash Grey @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3
-initial_exposure_time = 32
-material_type = Tough
-material_vendor = FunToDo
-material_colour = #808080
-
-[sla_material:Ameralabs AMD 3 LED @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 1.7
-initial_exposure_time = 24
-material_type = Tough
-material_vendor = Ameralabs
-material_colour = #808080
-
-[sla_material:Dragon Resin Metalshine Metal Grey @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 10
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = Dragon Resin
-material_colour = #808080
-
-[sla_material:Dragon Resin Metalshine Dark Brass @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 10
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = Dragon Resin
-material_colour = #B0B000
-
-[sla_material:Dragon Resin Metalshine Brass @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 10
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = Dragon Resin
-material_colour = #B0B000
-
-[sla_material:Esun Bio-Photopolymer Resin White @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.7
-initial_exposure_time = 24
-material_type = Tough
-material_vendor = Esun
-material_colour = #FFFFFF
-
-[sla_material:Esun Standard Resin Black @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.3
-initial_exposure_time = 24
-material_type = Tough
-material_vendor = Esun
-material_colour = #595959
-
-[sla_material:Monocure 3D Black Rapid Resin @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = Monocure
-material_colour = #595959
-
-[sla_material:Monocure 3D Blue Rapid Resin @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.3
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = Monocure
-material_colour = #007EFD
-
-[sla_material:Monocure 3D Clear Rapid Resin @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2.7
-initial_exposure_time = 32
-material_type = Tough
-material_vendor = Monocure
-material_colour = #F8F8F8
-
-[sla_material:Monocure 3D Grey Rapid Resin @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3.3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Monocure
-material_colour = #C0C0C0
-
-[sla_material:Monocure 3D White Rapid Resin @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 3.3
-initial_exposure_time = 28
-material_type = Tough
-material_vendor = Monocure
-material_colour = #FFFFFF
-
-[sla_material:Photocentric Hard Grey @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 5
-initial_exposure_time = 24
-material_type = Tough
-material_vendor = Photocentric
-material_colour = #808080
-
-[sla_material:Liqcreate Clear Impact @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 10
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = Liqcreate
-material_colour = #F8F8F8
-
-[sla_material:Liqcreate Strong X @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 10
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = Liqcreate
-material_colour = #C0C0C0
-
-[sla_material:Resinworks 3D Green @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 7
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Resinworks 3D
-material_colour = #00B900
-
-[sla_material:3DJake Blue @0.05 SL1S]
-inherits = *0.05_sl1s*
-exposure_time = 2
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = 3DJake
-material_colour = #007EFD
-
-## 0.1 SL1S
-
-## Prusa Polymers 0.1
-
-[sla_material:Prusament Resin Tough Prusa Orange @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #FF8040
-
-[sla_material:Prusament Resin Tough Rich Black @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #595959
-
-[sla_material:Prusament Resin Tough Anthracite Grey @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #808080
-
-[sla_material:Prusament Resin Tough Sandstone Model @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #EEA061
-
-[sla_material:Prusament Resin Tough Terra Brown @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #7A5C45
-
-[sla_material:Prusament Resin Tough Brick Red @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #B46056
-
-[sla_material:Prusament Resin Tough Grass Green @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #37823F
-
-[sla_material:Prusament Resin Tough Bright Yellow @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #F9DB4C
-
-[sla_material:Prusament Resin Tough Transparent Green @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #1DAf5E
-
-[sla_material:Prusament Resin Tough Transparent Red @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #D21B31
-
-[sla_material:Prusament Resin Tough Transparent Amber @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 3.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Prusa Polymers
-material_colour = #FCB30E
-
-## Made for Prusa 0.1
-
-[sla_material:Prusa Orange Tough @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:Prusa White ABS like @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFFFF
-
-[sla_material:Prusa Azure Blue Tough @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-[sla_material:Prusa Black Tough @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #595959
-
-[sla_material:Prusa Cyan Tough @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #79FFFF
-
-[sla_material:Prusa Magenta Tough @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #E800E8
-
-[sla_material:Prusa Maroon Tough @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #804000
-
-[sla_material:Prusa White Tough @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FFFFFF
-
-[sla_material:Prusa Pink Tough @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF80C0
-
-[sla_material:Prusa Blue Flexible @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Flexible
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-[sla_material:Prusa Grey Tough @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-[sla_material:Prusa Grey High Tenacity @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #808080
-
-[sla_material:Prusa Vibrant Orange Tough @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 10
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #FF8040
-
-[sla_material:Prusa Deep Blue Transparent Tough @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 10
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Made for Prusa
-material_colour = #007EFD
-
-[sla_material:Prusa Green Dental Casting @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 8
-initial_exposure_time = 50
-material_type = Casting
-material_vendor = Made for Prusa
-material_colour = #00B900
-
-[sla_material:Ameralabs TGM-7 LED @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Ameralabs
-material_colour = #C0C0C0
-material_print_speed = slow
-
-[sla_material:BASF Ultracur3D RG 35 @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 10
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #FFEEE6
-
-[sla_material:BASF Ultracur3D ST 45 @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 7.5
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:BASF Ultracur3D ST 45 M @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 4.5
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:BASF Ultracur3D ST 80 @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 9
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #FFEEE6
-
-[sla_material:BASF Ultracur3D ST 80 White @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 9
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #FFFFFF
-
-[sla_material:BASF Ultracur3D ST 80 Black @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 9
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:BASF Ultracur3D EL 150 Black @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 5
-initial_exposure_time = 25
-material_type = Flexible
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:BASF Ultracur3D FL 300 Black @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 6
-initial_exposure_time = 25
-material_type = Flexible
-material_vendor = BASF
-material_colour = #595959
-
-[sla_material:PrimaCreator Tough Light Grey @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #C0C0C0
-
-[sla_material:PrimaCreator Tough Clear @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:PrimaCreator Tough White @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #FFFFFF
-
-[sla_material:PrimaCreator Flex Clear @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Flexible
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:PrimaCreator Water Washable Transparent @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = PrimaCreator
-material_colour = #F8F8F8
-
-[sla_material:DruckWege Type D Dental Model @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 15
-material_type = Dental
-material_vendor = DruckWege
-material_colour = #FFEEE6
-material_print_speed = slow
-
-[sla_material:3DM-ABS Orange @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = 3DM
-material_colour = #FF8040
-
-[sla_material:3DM-TOUGH Clear @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = 3DM
-material_colour = #F8F8F8
-
-[sla_material:Peopoly Deft White @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Peopoly
-material_colour = #FFFFFF
-
-[sla_material:Peopoly Neo Clear @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 2.6
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Peopoly
-material_colour = #F8F8F8
-
-[sla_material:Liqcreate Clear Impact @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 20
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = Liqcreate
-material_colour = #F8F8F8
-
-[sla_material:Liqcreate Strong X @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 20
-initial_exposure_time = 40
-material_type = Tough
-material_vendor = Liqcreate
-material_colour = #C0C0C0
-
-[sla_material:Resinworks 3D Green @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 13
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = Resinworks 3D
-material_colour = #00B900
-
-[sla_material:3DJake Blue @0.1 SL1S]
-inherits = *0.1_sl1s*
-exposure_time = 3
-initial_exposure_time = 25
-material_type = Tough
-material_vendor = 3DJake
-material_colour = #007EFD
-
-[printer:*common*]
-printer_technology = FFF
-bed_shape = 0x0,250x0,250x210,0x210
-before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
-between_objects_gcode = 
-deretract_speed = 0
-end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y200 F3600 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM900 K0 ; reset LA\nM84 ; disable motors
-extruder_offset = 0x0
-gcode_flavor = marlin
-silent_mode = 0
-remaining_times = 1
-machine_max_acceleration_e = 10000
-machine_max_acceleration_extruding = 2000
-machine_max_acceleration_retracting = 1500
-machine_max_acceleration_x = 9000
-machine_max_acceleration_y = 9000
-machine_max_acceleration_z = 500
-machine_max_feedrate_e = 120
-machine_max_feedrate_x = 500
-machine_max_feedrate_y = 500
-machine_max_feedrate_z = 12
-machine_max_jerk_e = 2.5
-machine_max_jerk_x = 10
-machine_max_jerk_y = 10
-machine_max_jerk_z = 0.2
-machine_min_extruding_rate = 0
-machine_min_travel_rate = 0
-machine_limits_usage = emit_to_gcode
-layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
-max_layer_height = 0.25
-min_layer_height = 0.07
-max_print_height = 200
-nozzle_diameter = 0.4
-octoprint_apikey = 
-octoprint_host = 
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\n
-printer_settings_id = 
-retract_before_travel = 1
-retract_before_wipe = 0%
-retract_layer_change = 1
-retract_length = 0.8
-retract_length_toolchange = 4
-retract_lift = 0.4
-retract_lift_above = 0
-retract_lift_below = 199
-retract_restart_extra = 0
-retract_restart_extra_toolchange = 0
-retract_speed = 35
-serial_port = 
-serial_speed = 250000
-single_extruder_multi_material = 0
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.2.3 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM204 S[machine_max_acceleration_extruding] T[machine_max_acceleration_retracting] ; MK2 firmware only supports the old M204 format\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Z0.2 F720\nG1 Y-2 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E12.5 F1000 ; intro line\nG92 E0
-toolchange_gcode = 
-use_firmware_retraction = 0
-use_relative_e_distances = 1
-use_volumetric_e = 0
-variable_layer_height = 1
-wipe = 1
-z_offset = 0
-printer_model = MK2S
-printer_variant = 0.4
-default_print_profile = 0.15mm OPTIMAL
-default_filament_profile = Prusament PLA
-color_change_gcode = M600\nG1 E0.4 F1500 ; prime after color change
-
-[printer:*multimaterial*]
-inherits = *common*
-deretract_speed = 50
-retract_before_travel = 3
-retract_before_wipe = 60%
-retract_layer_change = 0
-retract_length = 4
-retract_lift = 0.6
-retract_lift_above = 0
-retract_lift_below = 199
-retract_restart_extra = 0
-retract_restart_extra_toolchange = 0
-retract_speed = 80
-parking_pos_retraction = 92
-cooling_tube_length = 5
-cooling_tube_retraction = 91.5
-single_extruder_multi_material = 1
-variable_layer_height = 1
-printer_model = MK2SMM
-
-[printer:*mm-single*]
-inherits = *multimaterial*
-end_gcode = G1 E-4 F2100\nG91\nG1 Z1 F7200\nG90\nG1 X245 Y1\nG1 X240 E4\nG1 F4000\nG1 X190 E2.7\nG1 F4600\nG1 X110 E2.8\nG1 F5200\nG1 X40 E3\nG1 E-15 F5000\nG1 E-50 F5400\nG1 E-15 F3000\nG1 E-12 F2000\nG1 F1600\nG1 X0 Y1 E3\nG1 X50 Y1 E-5\nG1 F2000\nG1 X0 Y1 E5\nG1 X50 Y1 E-5\nG1 F2400\nG1 X0 Y1 E5\nG1 X50 Y1 E-5\nG1 F2400\nG1 X0 Y1 E5\nG1 X50 Y1 E-3\nG4 S0\nM107 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+50, max_print_height)}{endif} ; Move print head up\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nM900 K0 ; reset LA\nM84     ; disable motors\n\n
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\nPRINTER_HAS_BOWDEN
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.2.3 ; tell printer latest fw version\nM204 S[machine_max_acceleration_extruding] T[machine_max_acceleration_retracting] ; MK2 firmware only supports the old M204 format\n; Start G-Code sequence START\nT?\nM104 S[first_layer_temperature]\nM140 S[first_layer_bed_temperature]\nM109 S[first_layer_temperature]\nM190 S[first_layer_bed_temperature]\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG28 W\nG80\nG92 E0\nM203 E100\nM92 E140\nG1 Z0.25 F7200\nG1 X50 E80 F1000\nG1 X160 E20 F1000\nG1 Z0.2 F7200\nG1 X220 E13 F1000\nG1 X240 E0 F1000\nG92 E0
-default_print_profile = 0.15mm OPTIMAL
-
-[printer:*mm-multi*]
-inherits = *multimaterial*
-high_current_on_filament_swap = 1
-end_gcode = {if not has_wipe_tower}\n; Pull the filament into the cooling tubes.\nG1 E-4 F2100\nG91\nG1 Z1 F7200\nG90\nG1 X245 Y1\nG1 X240 E4\nG1 F4000\nG1 X190 E2.7\nG1 F4600\nG1 X110 E2.8\nG1 F5200\nG1 X40 E3\nG1 E-15 F5000\nG1 E-50 F5400\nG1 E-15 F3000\nG1 E-12 F2000\nG1 F1600\nG1 X0 Y1 E3\nG1 X50 Y1 E-5\nG1 F2000\nG1 X0 Y1 E5\nG1 X50 Y1 E-5\nG1 F2400\nG1 X0 Y1 E5\nG1 X50 Y1 E-5\nG1 F2400\nG1 X0 Y1 E5\nG1 X50 Y1 E-3\nG4 S0\n{endif}\nM107 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+50, max_print_height)}{endif} ; Move print head up\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nM900 K0 ; reset LA\nM84     ; disable motors
-extruder_colour = #FFAA55;#E37BA0;#4ECDD3;#FB7259
-nozzle_diameter = 0.4,0.4,0.4,0.4
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\nPRINTER_HAS_BOWDEN
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.2.3 ; tell printer latest fw version\nM204 S[machine_max_acceleration_extruding] T[machine_max_acceleration_retracting] ; MK2 firmware only supports the old M204 format\n; Start G-Code sequence START\nT[initial_tool]\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG28 W\nG80\nG92 E0\nM203 E100 ; set max feedrate\nM92 E140 ; E-steps per filament milimeter\n{if not has_single_extruder_multi_material_priming}\nG1 Z0.25 F7200\nG1 X50 E80 F1000\nG1 X160 E20 F1000\nG1 Z0.2 F7200\nG1 X220 E13 F1000\nG1 X240 E0 F1000\n{endif}\nG92 E0
-default_print_profile = 0.15mm OPTIMAL
-
-# XXXXXXXXXXXXXXXXX
-# XXX--- MK2 ---XXX
-# XXXXXXXXXXXXXXXXX
-
-[printer:Original Prusa i3 MK2S]
-inherits = *common*
-
-[printer:Original Prusa i3 MK2S 0.25 nozzle]
-inherits = *common*
-max_layer_height = 0.15
-min_layer_height = 0.05
-nozzle_diameter = 0.25
-retract_length = 1
-retract_speed = 50
-variable_layer_height = 1
-printer_variant = 0.25
-retract_lift = 0.15
-default_print_profile = 0.10mm DETAIL 0.25 nozzle
-color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK2S 0.6 nozzle]
-inherits = *common*
-max_layer_height = 0.35
-min_layer_height = 0.1
-nozzle_diameter = 0.6
-printer_variant = 0.6
-default_print_profile = 0.20mm NORMAL @0.6 nozzle
-color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
-
-# XXXXXXXXXXXXXXXXXXX
-# XXX--- MK2MM ---XXX
-# XXXXXXXXXXXXXXXXXXX
-
-[printer:Original Prusa i3 MK2S MMU1 Single]
-inherits = *mm-single*
-max_layer_height = 0.25
-min_layer_height = 0.07
-
-[printer:Original Prusa i3 MK2S MMU1 Single 0.6 nozzle]
-inherits = *mm-single*
-nozzle_diameter = 0.6
-printer_variant = 0.6
-default_print_profile = 0.20mm NORMAL @0.6 nozzle
-max_layer_height = 0.35
-min_layer_height = 0.1
-
-[printer:Original Prusa i3 MK2S MMU1]
-inherits = *mm-multi*
-nozzle_diameter = 0.4,0.4,0.4,0.4
-max_layer_height = 0.25
-min_layer_height = 0.07
-
-[printer:Original Prusa i3 MK2S MMU1 0.6 nozzle]
-inherits = *mm-multi*
-nozzle_diameter = 0.6,0.6,0.6,0.6
-printer_variant = 0.6
-default_print_profile = 0.20mm NORMAL @0.6 nozzle
-max_layer_height = 0.35
-min_layer_height = 0.1
-
-# XXXXXXXXXXXXXXXXXXX
-# XXX--- MK2.5 ---XXX
-# XXXXXXXXXXXXXXXXXXX
-
-[printer:Original Prusa i3 MK2.5]
-inherits = Original Prusa i3 MK2S
-printer_model = MK2.5
-remaining_times = 1
-machine_max_jerk_e = 4.5
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n{if filament_settings_id[initial_tool]=~/.*Prusament PA11.*/}\nG1 Z0.3 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E9 F1000 ; intro line\n{else}\nG1 Z0.2 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E12.5 F1000 ; intro line\n{endif}\nG92 E0
-
-[printer:Original Prusa i3 MK2.5 0.25 nozzle]
-inherits = Original Prusa i3 MK2S 0.25 nozzle
-printer_model = MK2.5
-remaining_times = 1
-machine_max_jerk_e = 4.5
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Z0.2 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E12.5 F1000 ; intro line\nG92 E0
-
-[printer:Original Prusa i3 MK2.5 0.6 nozzle]
-inherits = Original Prusa i3 MK2S 0.6 nozzle
-printer_model = MK2.5
-remaining_times = 1
-machine_max_jerk_e = 4.5
-deretract_speed = 25
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n{if filament_settings_id[initial_tool]=~/.*Prusament PA11.*/}\nG1 Z0.3 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E9 F1000 ; intro line\n{else}\nG1 Z0.2 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E12.5 F1000 ; intro line\n{endif}\nG92 E0
-
-[printer:Original Prusa i3 MK2.5 0.8 nozzle]
-inherits = Original Prusa i3 MK2S 0.6 nozzle
-printer_model = MK2.5
-nozzle_diameter = 0.8
-printer_variant = 0.8
-max_layer_height = 0.6
-min_layer_height = 0.2
-retract_length = 0.7
-retract_speed = 35
-deretract_speed = 20
-retract_lift = 0.25
-remaining_times = 1
-machine_max_jerk_e = 4.5
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n{if filament_settings_id[initial_tool]=~/.*Prusament PA11.*/}\nG1 Z0.3 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E9 F1000 ; intro line\n{else}\nG1 Z0.2 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E12.5 F1000 ; intro line\n{endif}\nG92 E0
-default_print_profile = 0.40mm QUALITY @0.8 nozzle
-default_filament_profile = Prusament PLA @0.8 nozzle
-color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK2.5 MMU2 Single]
-inherits = *25mm2*
-printer_model = MK2.5MMU2
-single_extruder_multi_material = 0
-max_print_height = 200
-default_print_profile = 0.15mm OPTIMAL @MK2.5
-default_filament_profile = Prusament PLA
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2.5\n
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\n; select extruder\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; load to nozzle\nTc\n; purge line\nG1 X55 E8 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.20 F1000\nG1 X5 E4 F1000\nG92 E0\n
-end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y210 F7200 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15 F5800\nG1 E-20 F5500\nG1 E10 F3000\nG1 E-10 F3100\nG1 E10 F3150\nG1 E-10 F3250\nG1 E10 F3300\n\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM702 C\nG4 ; wait\nM104 S0 ; turn off temperature\nM900 K0 ; reset LA\nM84 ; disable motors
-
-[printer:Original Prusa i3 MK2.5 MMU2 Single 0.8 nozzle]
-inherits = Original Prusa i3 MK2.5S MMU2S Single 0.8 nozzle
-printer_model = MK2.5MMU2
-
-[printer:Original Prusa i3 MK2.5 MMU2 Single 0.6 nozzle]
-inherits = Original Prusa i3 MK2.5S MMU2S Single 0.6 nozzle
-printer_model = MK2.5MMU2
-
-[printer:Original Prusa i3 MK2.5 MMU2 Single 0.25 nozzle]
-inherits = Original Prusa i3 MK2.5S MMU2S Single 0.25 nozzle
-printer_model = MK2.5MMU2
-
-[printer:Original Prusa i3 MK2.5 MMU2]
-inherits = *25mm2*
-printer_model = MK2.5MMU2
-max_print_height = 200
-default_print_profile = 0.15mm OPTIMAL @MK2.5
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2.5\n
-single_extruder_multi_material = 1
-nozzle_diameter = 0.4,0.4,0.4,0.4,0.4
-extruder_colour = #FF8000;#DB5182;#3EC0FF;#FF4F4F;#FBEB7D
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55 E32 F1073\nG1 X5 E32 F1800\nG1 X55 E8 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\nG92 E0\n{endif}\nG92 E0\n
-end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y210 F7200 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\n{if has_wipe_tower}\nG1 E-15 F3000\n{else}\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15 F5800\nG1 E-20 F5500\nG1 E10 F3000\nG1 E-10 F3100\nG1 E10 F3150\nG1 E-10 F3250\nG1 E10 F3300\n{endif}\n\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n\n; Unload filament\nM702 C\n\nG4 ; wait\nM104 S0 ; turn off temperature\nM900 K0 ; reset LA\nM84 ; disable motors\n
-
-[printer:Original Prusa i3 MK2.5S]
-inherits = Original Prusa i3 MK2.5
-printer_model = MK2.5S
-
-[printer:Original Prusa i3 MK2.5S 0.25 nozzle]
-inherits = Original Prusa i3 MK2.5 0.25 nozzle
-printer_model = MK2.5S
-
-[printer:Original Prusa i3 MK2.5S 0.6 nozzle]
-inherits = Original Prusa i3 MK2.5 0.6 nozzle
-printer_model = MK2.5S
-
-[printer:Original Prusa i3 MK2.5S 0.8 nozzle]
-inherits = Original Prusa i3 MK2.5 0.8 nozzle
-printer_model = MK2.5S
-
-[printer:Original Prusa i3 MK2.5S MMU2S Single]
-inherits = *25mm2s*
-printer_model = MK2.5SMMU2S
-single_extruder_multi_material = 0
-max_print_height = 200
-default_print_profile = 0.15mm OPTIMAL @MK2.5
-default_filament_profile = Prusament PLA
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2.5\n
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nTc\n; purge line\nG1 X55 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\nG92 E0\n
-end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y210 F7200 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15 F5800\nG1 E-20 F5500\nG1 E10 F3000\nG1 E-10 F3100\nG1 E10 F3150\nG1 E-10 F3250\nG1 E10 F3300\n\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM702 C\nG4 ; wait\nM104 S0 ; turn off temperature\nM900 K0 ; reset LA\nM84 ; disable motors
-
-[printer:Original Prusa i3 MK2.5S MMU2S Single 0.8 nozzle]
-inherits = Original Prusa i3 MK2.5S MMU2S Single
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\n
-max_layer_height = 0.6
-min_layer_height = 0.2
-nozzle_diameter = 0.8
-printer_variant = 0.8
-retract_length = 0.7
-retract_speed = 35
-deretract_speed = 20
-retract_lift = 0.25
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nTc\n; purge line\nG1 X55 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\nG92 E0\n
-default_print_profile = 0.40mm QUALITY @0.8 nozzle
-default_filament_profile = Prusament PLA @0.8 nozzle
-color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK2.5S MMU2S Single 0.6 nozzle]
-inherits = Original Prusa i3 MK2.5S MMU2S Single
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\n
-max_layer_height = 0.35
-min_layer_height = 0.1
-nozzle_diameter = 0.6
-printer_variant = 0.6
-deretract_speed = 25
-default_print_profile = 0.20mm NORMAL @0.6 nozzle
-color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK2.5S MMU2S Single 0.25 nozzle]
-inherits = Original Prusa i3 MK2.5S MMU2S Single
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\n
-max_layer_height = 0.15
-min_layer_height = 0.05
-nozzle_diameter = 0.25
-printer_variant = 0.25
-retract_lift = 0.15
-default_print_profile = 0.10mm DETAIL 0.25 nozzle
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nTc\n; purge line\nG1 X55 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F1400\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\nG92 E0\n
-color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK2.5S MMU2S]
-inherits = *25mm2s*
-printer_model = MK2.5SMMU2S
-max_print_height = 200
-default_print_profile = 0.15mm OPTIMAL @MK2.5
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2.5\n
-single_extruder_multi_material = 1
-nozzle_diameter = 0.4,0.4,0.4,0.4,0.4
-extruder_colour = #FF8000;#DB5182;#3EC0FF;#FF4F4F;#FBEB7D
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55 E29 F1073\nG1 X5 E29 F1800\nG1 X55 E8 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\nG92 E0\n{endif}\nG92 E0\n
-end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y210 F7200 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\n{if has_wipe_tower}\nG1 E-15 F3000\n{else}\nG1 X0 Y210 F7200\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15 F5800\nG1 E-20 F5500\nG1 E10 F3000\nG1 E-10 F3100\nG1 E10 F3150\nG1 E-10 F3250\nG1 E10 F3300\n{endif}\n\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n\n; Unload filament\nM702 C\n\nG4 ; wait\nM104 S0 ; turn off temperature\nM900 K0 ; reset LA\nM84 ; disable motors\n
-
-[printer:Original Prusa i3 MK2.5S MMU2S 0.6 nozzle]
-inherits = Original Prusa i3 MK2.5S MMU2S
-nozzle_diameter = 0.6,0.6,0.6,0.6,0.6
-max_layer_height = 0.40
-min_layer_height = 0.15
-printer_variant = 0.6
-deretract_speed = 25
-default_print_profile = 0.20mm NORMAL @0.6 nozzle
-color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK2.5 MMU2 0.6 nozzle]
-inherits = Original Prusa i3 MK2.5 MMU2
-nozzle_diameter = 0.6,0.6,0.6,0.6,0.6
-max_layer_height = 0.40
-min_layer_height = 0.15
-printer_variant = 0.6
-deretract_speed = 25
-default_print_profile = 0.20mm NORMAL @0.6 nozzle
-color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK2.5S MMU2S 0.25 nozzle]
-inherits = Original Prusa i3 MK2.5S MMU2S
-nozzle_diameter = 0.25,0.25,0.25,0.25,0.25
-max_layer_height = 0.15
-min_layer_height = 0.05
-printer_variant = 0.25
-default_print_profile = 0.10mm DETAIL @0.25 nozzle
-default_filament_profile = Prusament PLA @MMU2 0.25
-color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK2.5 MMU2 0.25 nozzle]
-inherits = Original Prusa i3 MK2.5 MMU2
-nozzle_diameter = 0.25,0.25,0.25,0.25,0.25
-max_layer_height = 0.15
-min_layer_height = 0.05
-printer_variant = 0.25
-default_print_profile = 0.10mm DETAIL @0.25 nozzle
-default_filament_profile = Prusament PLA @MMU2 0.25
-color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
-
-## 0.8mm nozzle profiles are only available for MMU2 Single mode at the moment.
-
-## [printer:Original Prusa i3 MK2.5S MMU2S 0.8 nozzle]
-## inherits = Original Prusa i3 MK2.5S MMU2S
-## nozzle_diameter = 0.8,0.8,0.8,0.8,0.8
-## max_layer_height = 0.6
-## min_layer_height = 0.2
-## printer_variant = 0.8
-## retract_length = 1
-## default_print_profile = 0.40mm QUALITY @0.8 nozzle
-## start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3.0 F1000.0\nG1 Z0.4 F1000.0\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55.0 E29.0 F1073.0\nG1 X5.0 E29.0 F1800.0\nG1 X55.0 E8.0 F2000.0\nG1 Z0.3 F1000.0\nG92 E0.0\nG1 X240.0 E25.0 F2200.0\nG1 Y-2.0 F1000.0\nG1 X55.0 E25 F1400.0\nG1 Z0.20 F1000.0\nG1 X5.0 E4.0 F1000.0\nG92 E0.0\n{endif}\nG92 E0.0\n
-
-## [printer:Original Prusa i3 MK2.5 MMU2 0.8 nozzle]
-## inherits = Original Prusa i3 MK2.5 MMU2
-## nozzle_diameter = 0.8,0.8,0.8,0.8,0.8
-## max_layer_height = 0.6
-## min_layer_height = 0.2
-## printer_variant = 0.8
-## retract_length = 1
-## default_print_profile = 0.40mm QUALITY @0.8 nozzle
-## start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3.0 F1000.0\nG1 Z0.4 F1000.0\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55.0 E29.0 F1073.0\nG1 X5.0 E29.0 F1800.0\nG1 X55.0 E8.0 F2000.0\nG1 Z0.3 F1000.0\nG92 E0.0\nG1 X240.0 E25.0 F2200.0\nG1 Y-2.0 F1000.0\nG1 X55.0 E25 F1400.0\nG1 Z0.20 F1000.0\nG1 X5.0 E4.0 F1000.0\nG92 E0.0\n{endif}\nG92 E0.0\n
-
-# XXXXXXXXXXXXXXXXX
-# XXX--- MK3 ---XXX
-# XXXXXXXXXXXXXXXXX
-
-[printer:Original Prusa i3 MK3]
-inherits = *common*
-end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y200 F3600 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\nG4 ; wait\nM221 S100 ; reset flow\nM900 K0 ; reset LA\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|@0.25 nozzle MK3).*/}M907 E538 ; reset extruder motor current{endif}\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM84 ; disable motors
-machine_max_acceleration_e = 5000,5000
-machine_max_acceleration_extruding = 1250,1250
-machine_max_acceleration_retracting = 1250,1250
-machine_max_acceleration_x = 1000,960
-machine_max_acceleration_y = 1000,960
-machine_max_acceleration_z = 200,200
-machine_max_feedrate_e = 120,120
-machine_max_feedrate_x = 200,100
-machine_max_feedrate_y = 200,100
-machine_max_feedrate_z = 12,12
-machine_max_jerk_e = 4.5,4.5
-machine_max_jerk_x = 8,8
-machine_max_jerk_y = 8,8
-machine_max_jerk_z = 0.4,0.4
-machine_min_extruding_rate = 0,0
-machine_min_travel_rate = 0,0
-silent_mode = 1
-remaining_times = 1
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n
-retract_lift_below = 209
-max_print_height = 210
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n{if filament_settings_id[initial_tool]=~/.*Prusament PA11.*/}\nG1 Z0.3 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E9 F1000 ; intro line\n{else}\nG1 Z0.2 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E12.5 F1000 ; intro line\n{endif}\nG92 E0\nM221 S{if layer_height<0.075}100{else}95{endif}\n\n; Don't change E values below. Excessive value can damage the printer.\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3).*/}M907 E430 ; set extruder motor current{endif}\n{if print_settings_id=~/.*(SPEED @MK3|DRAFT @MK3).*/}M907 E538 ; set extruder motor current{endif}
-printer_model = MK3
-default_print_profile = 0.15mm QUALITY @MK3
-thumbnails = 160x120
-
-[printer:Original Prusa i3 MK3 0.25 nozzle]
-inherits = Original Prusa i3 MK3
-nozzle_diameter = 0.25
-max_layer_height = 0.15
-min_layer_height = 0.05
-printer_variant = 0.25
-retract_lift = 0.15
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Z0.2 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E8 F700 ; intro line\nG1 X100 E12.5 F700 ; intro line\nG92 E0\nM221 S{if layer_height<0.075}100{else}95{endif}\n\n; Don't change E value below. Excessive value can damage the printer.\n{if print_settings_id=~/.*@0.25 nozzle MK3.*/}M907 E430 ; set extruder motor current{endif}
-default_print_profile = 0.10mm DETAIL @0.25 nozzle MK3
-color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK3 0.6 nozzle]
-inherits = Original Prusa i3 MK3
-nozzle_diameter = 0.6
-max_layer_height = 0.40
-min_layer_height = 0.15
-printer_variant = 0.6
-deretract_speed = 25
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n{if filament_settings_id[initial_tool]=~/.*Prusament PA11.*/}\nG1 Z0.3 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E9 F1000 ; intro line\n{else}\nG1 Z0.2 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E12.5 F1000 ; intro line\n{endif}\nG92 E0\nM221 S{if layer_height<0.075}100{else}95{endif}
-default_print_profile = 0.30mm QUALITY @0.6 nozzle MK3
-color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK3 0.8 nozzle]
-inherits = Original Prusa i3 MK3
-nozzle_diameter = 0.8
-max_layer_height = 0.6
-min_layer_height = 0.2
-printer_variant = 0.8
-retract_length = 0.7
-retract_speed = 35
-deretract_speed = 20
-retract_lift = 0.25
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n{if filament_settings_id[initial_tool]=~/.*Prusament PA11.*/}\nG1 Z0.3 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E9 F1000 ; intro line\n{else}\nG1 Z0.2 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E12.5 F1000 ; intro line\n{endif}\nG92 E0\nM221 S95
-default_print_profile = 0.40mm QUALITY @0.8 nozzle
-default_filament_profile = Prusament PLA @0.8 nozzle
-color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK3S & MK3S+]
-inherits = Original Prusa i3 MK3
-renamed_from = "Original Prusa i3 MK3S"
-printer_model = MK3S
-
-[printer:Original Prusa i3 MK3S & MK3S+ 0.25 nozzle]
-inherits = Original Prusa i3 MK3 0.25 nozzle
-renamed_from = "Original Prusa i3 MK3S 0.25 nozzle"
-printer_model = MK3S
-
-[printer:Original Prusa i3 MK3S & MK3S+ 0.6 nozzle]
-inherits = Original Prusa i3 MK3 0.6 nozzle
-renamed_from = "Original Prusa i3 MK3S 0.6 nozzle"
-printer_model = MK3S
-
-[printer:Original Prusa i3 MK3S & MK3S+ 0.8 nozzle]
-inherits = Original Prusa i3 MK3 0.8 nozzle
-printer_model = MK3S
-
-[printer:*mm2*]
-inherits = Original Prusa i3 MK3
-single_extruder_multi_material = 1
-cooling_tube_length = 10
-cooling_tube_retraction = 30
-parking_pos_retraction = 85
-retract_length_toolchange = 0
-extra_loading_move = -13
-printer_model = MK3MMU2
-default_print_profile = 0.15mm QUALITY @MK3
-default_filament_profile = Prusament PLA @MMU2
-
-[printer:*mm2s*]
-inherits = Original Prusa i3 MK3
-single_extruder_multi_material = 1
-cooling_tube_length = 20
-cooling_tube_retraction = 40
-parking_pos_retraction = 85
-retract_length_toolchange = 0
-extra_loading_move = -25
-printer_model = MK3SMMU2S
-default_print_profile = 0.15mm QUALITY @MK3
-default_filament_profile = Prusament PLA @MMU2
-
-[printer:*25mm2*]
-inherits = Original Prusa i3 MK2.5
-single_extruder_multi_material = 1
-cooling_tube_length = 10
-cooling_tube_retraction = 30
-parking_pos_retraction = 85
-retract_length_toolchange = 0
-extra_loading_move = -13
-default_filament_profile = Prusament PLA @MMU2
-
-[printer:*25mm2s*]
-inherits = Original Prusa i3 MK2.5S
-single_extruder_multi_material = 1
-cooling_tube_length = 20
-cooling_tube_retraction = 40
-parking_pos_retraction = 85
-retract_length_toolchange = 0
-extra_loading_move = -25
-default_filament_profile = Prusament PLA @MMU2
-
-[printer:Original Prusa i3 MK3 MMU2 Single]
-inherits = *mm2*
-single_extruder_multi_material = 0
-default_filament_profile = Prusament PLA
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nTc\n; purge line\nG1 X55 E8 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0\n\n; Don't change E values below. Excessive value can damage the printer.\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3).*/}M907 E430 ; set extruder motor current{endif}\n{if print_settings_id=~/.*(SPEED @MK3|DRAFT @MK3).*/}M907 E538 ; set extruder motor current{endif}
-end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y210 F7200 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15 F5800\nG1 E-20 F5500\nG1 E10 F3000\nG1 E-10 F3100\nG1 E10 F3150\nG1 E-10 F3250\nG1 E10 F3300\n\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM702 C\nG4 ; wait\nM221 S100 ; reset flow\nM900 K0 ; reset LA\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|@0.25 nozzle MK3).*/}M907 E538 ; reset extruder motor current{endif}\nM104 S0 ; turn off temperature\nM84 ; disable motors
-
-[printer:Original Prusa i3 MK3 MMU2 Single 0.6 nozzle]
-inherits = Original Prusa i3 MK3 MMU2 Single
-single_extruder_multi_material = 0
-nozzle_diameter = 0.6
-max_layer_height = 0.40
-min_layer_height = 0.15
-printer_variant = 0.6
-deretract_speed = 25
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nTc\n; purge line\nG1 X55 E8 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0
-default_print_profile = 0.30mm QUALITY @0.6 nozzle MK3
-color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK3 MMU2 Single 0.8 nozzle]
-inherits = Original Prusa i3 MK3 MMU2 Single 0.6 nozzle
-single_extruder_multi_material = 0
-nozzle_diameter = 0.8
-max_layer_height = 0.6
-min_layer_height = 0.2
-printer_variant = 0.8
-retract_length = 0.7
-retract_speed = 35
-deretract_speed = 20
-retract_lift = 0.25
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nTc\n; purge line\nG1 X55 E8 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0
-default_print_profile = 0.40mm QUALITY @0.8 nozzle
-default_filament_profile = Prusament PLA @0.8 nozzle
-color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK3 MMU2 Single 0.25 nozzle]
-inherits = Original Prusa i3 MK3 MMU2 Single
-single_extruder_multi_material = 0
-nozzle_diameter = 0.25
-max_layer_height = 0.15
-min_layer_height = 0.05
-printer_variant = 0.25
-retract_lift = 0.15
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nTc\n; purge line\nG1 X55 E8 F1000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F1400\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0\n\n; Don't change E value below. Excessive value can damage the printer.\n{if print_settings_id=~/.*@0.25 nozzle MK3.*/}M907 E430 ; set extruder motor current{endif}
-default_print_profile = 0.10mm DETAIL @0.25 nozzle MK3
-color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK3 MMU2]
-inherits = *mm2*
-machine_max_acceleration_e = 8000,8000
-nozzle_diameter = 0.4,0.4,0.4,0.4,0.4
-extruder_colour = #FF8000;#DB5182;#3EC0FF;#FF4F4F;#FBEB7D
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55 E32 F1073\nG1 X5 E32 F1800\nG1 X55 E8 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\nG92 E0\n{endif}\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0\n\n; Don't change E values below. Excessive value can damage the printer.\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|SOLUBLE).*/}M907 E430 ; set extruder motor current{endif}\n{if print_settings_id=~/.*(SPEED @MK3|DRAFT @MK3).*/}M907 E538 ; set extruder motor current{endif}
-end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y210 F7200 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\n{if has_wipe_tower}\nG1 E-15 F3000\n{else}\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15 F5800\nG1 E-20 F5500\nG1 E10 F3000\nG1 E-10 F3100\nG1 E10 F3150\nG1 E-10 F3250\nG1 E10 F3300\n{endif}\n\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n\n; Unload filament\nM702 C\n\nG4 ; wait\nM221 S100 ; reset flow\nM900 K0 ; reset LA\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|SOLUBLE|@0.25 nozzle MK3).*/}M907 E538 ; reset extruder motor current{endif}\nM104 S0 ; turn off temperature\nM84 ; disable motors\n
-
-[printer:Original Prusa i3 MK3S & MK3S+ MMU2S Single]
-inherits = *mm2s*
-renamed_from = "Original Prusa i3 MK3S MMU2S Single"
-single_extruder_multi_material = 0
-default_filament_profile = Prusament PLA
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nTc\n; purge line\nG1 X55 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0\n\n; Don't change E values below. Excessive value can damage the printer.\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3).*/}M907 E430 ; set extruder motor current{endif}\n{if print_settings_id=~/.*(SPEED @MK3|DRAFT @MK3).*/}M907 E538 ; set extruder motor current{endif}
-end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y210 F7200 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15 F5800\nG1 E-20 F5500\nG1 E10 F3000\nG1 E-10 F3100\nG1 E10 F3150\nG1 E-10 F3250\nG1 E10 F3300\n\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM702 C\nG4 ; wait\nM221 S100 ; reset flow\nM900 K0 ; reset LA\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|@0.25 nozzle MK3).*/}M907 E538 ; reset extruder motor current{endif}\nM104 S0 ; turn off temperature\nM84 ; disable motors
-
-[printer:Original Prusa i3 MK3S & MK3S+ MMU2S Single 0.6 nozzle]
-inherits = Original Prusa i3 MK3S & MK3S+ MMU2S Single
-renamed_from = "Original Prusa i3 MK3S MMU2S Single 0.6 nozzle"
-single_extruder_multi_material = 0
-nozzle_diameter = 0.6
-max_layer_height = 0.40
-min_layer_height = 0.15
-printer_variant = 0.6
-deretract_speed = 25
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nTc\n; purge line\nG1 X55 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0
-default_print_profile = 0.30mm QUALITY @0.6 nozzle MK3
-color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK3S & MK3S+ MMU2S Single 0.8 nozzle]
-inherits = Original Prusa i3 MK3S & MK3S+ MMU2S Single 0.6 nozzle
-single_extruder_multi_material = 0
-nozzle_diameter = 0.8
-max_layer_height = 0.6
-min_layer_height = 0.2
-printer_variant = 0.8
-retract_length = 0.7
-retract_speed = 35
-deretract_speed = 20
-retract_lift = 0.25
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nTc\n; purge line\nG1 X55 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0
-default_print_profile = 0.40mm QUALITY @0.8 nozzle
-default_filament_profile = Prusament PLA @0.8 nozzle
-color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK3S & MK3S+ MMU2S Single 0.25 nozzle]
-inherits = Original Prusa i3 MK3S & MK3S+ MMU2S Single
-renamed_from = "Original Prusa i3 MK3S MMU2S Single 0.25 nozzle"
-single_extruder_multi_material = 0
-nozzle_diameter = 0.25
-max_layer_height = 0.15
-min_layer_height = 0.05
-printer_variant = 0.25
-retract_lift = 0.15
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nTc\n; purge line\nG1 X55 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F1400\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0\n\n; Don't change E value below. Excessive value can damage the printer.\n{if print_settings_id=~/.*@0.25 nozzle MK3.*/}M907 E430 ; set extruder motor current{endif}
-default_print_profile = 0.10mm DETAIL @0.25 nozzle MK3
-color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK3S & MK3S+ MMU2S]
-inherits = *mm2s*
-renamed_from = "Original Prusa i3 MK3S MMU2S"
-machine_max_acceleration_e = 8000,8000
-nozzle_diameter = 0.4,0.4,0.4,0.4,0.4
-extruder_colour = #FF8000;#DB5182;#3EC0FF;#FF4F4F;#FBEB7D
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55 E29 F1073\nG1 X5 E29 F1800\nG1 X55 E8 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\nG92 E0\n{endif}\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0\n\n; Don't change E values below. Excessive value can damage the printer.\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|SOLUBLE).*/}M907 E430 ; set extruder motor current{endif}\n{if print_settings_id=~/.*(SPEED @MK3|DRAFT @MK3).*/}M907 E538 ; set extruder motor current{endif}
-end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y210 F7200 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\n{if has_wipe_tower}\nG1 E-15 F3000\n{else}\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15 F5800\nG1 E-20 F5500\nG1 E10 F3000\nG1 E-10 F3100\nG1 E10 F3150\nG1 E-10 F3250\nG1 E10 F3300\n{endif}\n\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n\n; Unload filament\nM702 C\n\nG4 ; wait\nM221 S100 ; reset flow\nM900 K0 ; reset LA\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|SOLUBLE|@0.25 nozzle MK3).*/}M907 E538 ; reset extruder motor current{endif}\nM104 S0 ; turn off temperature\nM84 ; disable motors\n
-
-## 0.6mm nozzle MMU2/S printer profiles
-
-[printer:Original Prusa i3 MK3S & MK3S+ MMU2S 0.6 nozzle]
-inherits = Original Prusa i3 MK3S & MK3S+ MMU2S
-renamed_from = "Original Prusa i3 MK3S MMU2S 0.6 nozzle"
-nozzle_diameter = 0.6,0.6,0.6,0.6,0.6
-max_layer_height = 0.40
-min_layer_height = 0.15
-printer_variant = 0.6
-deretract_speed = 25
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55 E29 F1073\nG1 X5 E29 F1800\nG1 X55 E8 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\nG92 E0\n{endif}\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0
-default_print_profile = 0.30mm QUALITY @0.6 nozzle MK3
-color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK3 MMU2 0.6 nozzle]
-inherits = Original Prusa i3 MK3 MMU2
-nozzle_diameter = 0.6,0.6,0.6,0.6,0.6
-max_layer_height = 0.40
-min_layer_height = 0.15
-printer_variant = 0.6
-deretract_speed = 25
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55 E32 F1073\nG1 X5 E32 F1800\nG1 X55 E8 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\nG92 E0\n{endif}\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0
-default_print_profile = 0.30mm QUALITY @0.6 nozzle MK3
-color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK3S & MK3S+ MMU2S 0.25 nozzle]
-inherits = Original Prusa i3 MK3S & MK3S+ MMU2S 0.6 nozzle
-nozzle_diameter = 0.25,0.25,0.25,0.25,0.25
-max_layer_height = 0.15
-min_layer_height = 0.05
-printer_variant = 0.25
-default_print_profile = 0.10mm DETAIL @0.25 nozzle MK3
-default_filament_profile = Prusament PLA @MMU2 0.25
-color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
-
-[printer:Original Prusa i3 MK3 MMU2 0.25 nozzle]
-inherits = Original Prusa i3 MK3 MMU2 0.6 nozzle
-nozzle_diameter = 0.25,0.25,0.25,0.25,0.25
-max_layer_height = 0.15
-min_layer_height = 0.05
-printer_variant = 0.25
-default_print_profile = 0.10mm DETAIL @0.25 nozzle MK3
-default_filament_profile = Prusament PLA @MMU2 0.25
-color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
-
-## 0.8mm nozzle MMU2/S printer profiles
-
-## For later use. 0.8mm nozzle profiles are only available for MMU2 Single mode at the moment.
-
-## [printer:Original Prusa i3 MK3 MMU2 0.8 nozzle]
-## inherits = Original Prusa i3 MK3 MMU2
-## nozzle_diameter = 0.8,0.8,0.8,0.8,0.8
-## max_layer_height = 0.6
-## min_layer_height = 0.2
-## printer_variant = 0.8
-## start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3.0 F1000\nG1 Z0.4 F1000\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55.0 E32.0 F1073.0\nG1 X5.0 E32.0 F1800.0\nG1 X55.0 E8.0 F2000.0\nG1 Z0.3 F1000\nG92 E0.0\nG1 X240.0 E25.0 F2200.0\nG1 Y-2.0 F1000.0\nG1 X55.0 E25 F1400.0\nG1 Z0.20 F1000.0\nG1 X5.0 E4.0 F1000.0\nG92 E0.0\n{endif}\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0.0
-## default_print_profile = 0.40mm QUALITY @0.8 nozzle
-
-## [printer:Original Prusa i3 MK3S & MK3S+ MMU2S 0.8 nozzle]
-## inherits = Original Prusa i3 MK3S & MK3S+ MMU2S
-## nozzle_diameter = 0.8,0.8,0.8,0.8,0.8
-## max_layer_height = 0.6
-## min_layer_height = 0.2
-## printer_variant = 0.8
-## start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3.0 F1000.0\nG1 Z0.4 F1000.0\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55.0 E29.0 F1073.0\nG1 X5.0 E29.0 F1800.0\nG1 X55.0 E8.0 F2000.0\nG1 Z0.3 F1000.0\nG92 E0.0\nG1 X240.0 E25.0 F2200.0\nG1 Y-2.0 F1000.0\nG1 X55.0 E25 F1400.0\nG1 Z0.20 F1000.0\nG1 X5.0 E4.0 F1000.0\nG92 E0.0\n{endif}\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0.0
-## default_print_profile = 0.40mm QUALITY @0.8 nozzle
-
-## MINI
-
-[printer:Original Prusa MINI & MINI+]
-inherits = *common*
-renamed_from = "Original Prusa MINI"
-printer_model = MINI
-printer_technology = FFF
-printer_variant = 0.4
-printer_vendor =
-thumbnails = 16x16,220x124
-bed_shape = 0x0,180x0,180x180,0x180
-default_filament_profile = "Prusament PLA"
-default_print_profile = 0.15mm QUALITY @MINI
-gcode_flavor = marlin2
-machine_max_acceleration_e = 5000
-machine_max_acceleration_extruding = 1250
-machine_max_acceleration_retracting = 1250
-machine_max_acceleration_travel = 2500
-machine_max_acceleration_x = 2500
-machine_max_acceleration_y = 2500
-machine_max_acceleration_z = 400
-machine_max_feedrate_e = 80
-machine_max_feedrate_x = 180
-machine_max_feedrate_y = 180
-machine_max_feedrate_z = 12
-machine_max_jerk_e = 10
-machine_max_jerk_x = 8
-machine_max_jerk_y = 8
-machine_max_jerk_z = 2
-machine_min_extruding_rate = 0
-machine_min_travel_rate = 0
-max_layer_height = 0.25
-max_print_height = 180
-min_layer_height = 0.07
-nozzle_diameter = 0.4
-retract_length = 3.2
-retract_lift = 0.2
-retract_speed = 70
-deretract_speed = 40
-wipe = 1
-retract_before_wipe = 70%
-retract_before_travel = 1.5
-retract_lift_above = 0
-retract_lift_below = 179
-retract_layer_change = 1
-silent_mode = 0
-remaining_times = 1
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S170 ; set extruder temp for bed leveling\nM140 S[first_layer_bed_temperature] ; set bed temp\nM109 R170 ; wait for bed leveling temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM204 T1250 ; set travel acceleration\nG28 ; home all without mesh bed level\nG29 ; mesh bed leveling \nM204 T[machine_max_acceleration_travel] ; restore travel acceleration\nM104 S[first_layer_temperature] ; set extruder temp\nG92 E0\nG1 Y-2 X179 F2400\nG1 Z3 F720\nM109 S[first_layer_temperature] ; wait for extruder temp\n\n; intro line\nG1 X170 F1000\nG1 Z0.2 F720\nG1 X110 E8 F900\nG1 X40 E10 F700\nG92 E0\n\nM221 S95 ; set flow
-end_gcode = G1 E-1 F2100 ; retract\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F720 ; Move print head up{endif}\nG1 X178 Y178 F4200 ; park print head\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)} F720 ; Move print head further up{endif}\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM221 S100 ; reset flow\nM900 K0 ; reset LA\nM84 ; disable motors
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MINI\n
-extruder_colour = 
-color_change_gcode = M600
-
-[printer:Original Prusa MINI & MINI+ 0.25 nozzle]
-inherits = Original Prusa MINI & MINI+
-renamed_from = "Original Prusa MINI 0.25 nozzle"
-printer_variant = 0.25
-nozzle_diameter = 0.25
-max_layer_height = 0.15
-min_layer_height = 0.05
-default_print_profile = 0.10mm DETAIL @0.25 nozzle MINI
-retract_length = 3
-retract_lift = 0.15
-retract_before_travel = 1
-start_gcode = M862.3 P \"[printer_model]\" ; printer model check\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S170 ; set extruder temp for bed leveling\nM140 S[first_layer_bed_temperature] ; set bed temp\nM109 R170 ; wait for bed leveling temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM204 T1250 ; set travel acceleration\nG28 ; home all without mesh bed level\nG29 ; mesh bed leveling \nM204 T[machine_max_acceleration_travel] ; restore travel acceleration\nM104 S[first_layer_temperature] ; set extruder temp\nG92 E0\nG1 Y-2 X179 F2400\nG1 Z3 F720\nM109 S[first_layer_temperature] ; wait for extruder temp\n\n; intro line\nG1 X170 F1000\nG1 Z0.2 F720\nG1 X110 E8 F600\nG1 X40 E10 F400\nG92 E0\n\nM221 S95 ; set flow
-
-[printer:Original Prusa MINI & MINI+ 0.6 nozzle]
-inherits = Original Prusa MINI & MINI+
-renamed_from = "Original Prusa MINI 0.6 nozzle"
-printer_variant = 0.6
-nozzle_diameter = 0.6
-max_layer_height = 0.40
-min_layer_height = 0.15
-default_print_profile = 0.30mm QUALITY @0.6 nozzle MINI
-retract_length = 3.2
-retract_before_travel = 1.5
-
-[printer:Original Prusa MINI & MINI+ 0.8 nozzle]
-inherits = Original Prusa MINI & MINI+
-printer_variant = 0.8
-nozzle_diameter = 0.8
-max_layer_height = 0.55
-min_layer_height = 0.2
-default_print_profile = 0.40mm QUALITY @0.8 nozzle MINI
-default_filament_profile = Prusament PLA @0.8 nozzle
-retract_length = 3
-retract_before_travel = 1.5
-retract_speed = 45
-deretract_speed = 20
-
-[printer:Original Prusa SL1]
-printer_technology = SLA
-printer_model = SL1
-printer_variant = default
-default_sla_material_profile = Prusa Orange Tough @0.05
-default_sla_print_profile = 0.05 Normal
-thumbnails = 400x400,800x480
-bed_shape = 1.48x1.02,119.48x1.02,119.48x67.02,1.48x67.02
-display_height = 68.04
-display_orientation = portrait
-display_pixels_x = 2560
-display_pixels_y = 1440
-display_width = 120.96
-max_print_height = 150
-min_exposure_time = 1
-max_exposure_time = 120
-min_initial_exposure_time = 1
-max_initial_exposure_time = 300
-printer_correction = 1,1,1
-printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_SL1\n
-
-[printer:Original Prusa SL1S SPEED]
-printer_technology = SLA
-printer_model = SL1S
-printer_variant = default
-default_sla_material_profile = Prusa Orange Tough @0.05 SL1S
-default_sla_print_profile = 0.05 Normal @SL1S
-thumbnails = 400x400,800x480
-bed_shape = 0.5x0.5,127.5x0.5,127.5x80.5,0.5x80.5
-display_height = 81
-display_mirror_x = 1
-display_mirror_y = 0
-display_orientation = portrait
-display_pixels_x = 2560
-display_pixels_y = 1620
-display_width = 128
-elefant_foot_compensation = 0.2
-elefant_foot_min_width = 0.2
-fast_tilt_time = 2.5
-slow_tilt_time = 5
-gamma_correction = 1
-max_print_height = 150
-min_exposure_time = 1
-max_exposure_time = 120
-min_initial_exposure_time = 1
-max_initial_exposure_time = 300
-printer_correction = 1,1,1
-relative_correction = 1,1
-area_fill = 45
-
-# The obsolete presets will be removed when upgrading from the legacy configuration structure (up to Slic3r 1.39.2) to 1.40.0 and newer.
-[obsolete_presets]
-print="0.05mm DETAIL 0.25 nozzle";"0.05mm DETAIL MK3";"0.05mm DETAIL";"0.20mm NORMAL MK3";"0.35mm FAST MK3";"print:0.15mm OPTIMAL MK3 MMU2";"print:0.20mm FAST MK3 MMU2"
-filament="ColorFabb Brass Bronze 1.75mm";"ColorFabb HT 1.75mm";"ColorFabb nGen 1.75mm";"ColorFabb Woodfil 1.75mm";"ColorFabb XT 1.75mm";"ColorFabb XT-CF20 1.75mm";"E3D PC-ABS 1.75mm";"Fillamentum ABS 1.75mm";"Fillamentum ASA 1.75mm";"Generic ABS 1.75mm";"Generic PET 1.75mm";"Generic PLA 1.75mm";"Prusa ABS 1.75mm";"Prusa HIPS 1.75mm";"Prusa PET 1.75mm";"Prusa PLA 1.75mm";"Taulman Bridge 1.75mm";"Taulman T-Glase 1.75mm"
diff --git a/deltazeus/marlin/.vscode/extensions.json b/deltazeus/marlin/.vscode/extensions.json
new file mode 100644
index 0000000..080e70d
--- /dev/null
+++ b/deltazeus/marlin/.vscode/extensions.json
@@ -0,0 +1,10 @@
+{
+    // See http://go.microsoft.com/fwlink/?LinkId=827846
+    // for the documentation about the extensions.json format
+    "recommendations": [
+        "platformio.platformio-ide"
+    ],
+    "unwantedRecommendations": [
+        "ms-vscode.cpptools-extension-pack"
+    ]
+}