# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-11 at 19:45:55 UTC
bed_custom_model = 
bed_custom_texture = 
bed_shape = 89.6575x7.84402,88.6327x15.6283,86.9333x23.2937,84.5723x30.7818,81.5677x38.0356,77.9423x45,73.7237x51.6219,68.944x57.8509,63.6396x63.6396,57.8509x68.944,51.6219x73.7237,45x77.9423,38.0356x81.5677,30.7818x84.5723,23.2937x86.9333,15.6283x88.6327,7.84402x89.6575,5.51091e-15x90,-7.84402x89.6575,-15.6283x88.6327,-23.2937x86.9333,-30.7818x84.5723,-38.0356x81.5677,-45x77.9423,-51.6219x73.7237,-57.8509x68.944,-63.6396x63.6396,-68.944x57.8509,-73.7237x51.6219,-77.9423x45,-81.5677x38.0356,-84.5723x30.7818,-86.9333x23.2937,-88.6327x15.6283,-89.6575x7.84402,-90x1.10218e-14,-89.6575x-7.84402,-88.6327x-15.6283,-86.9333x-23.2937,-84.5723x-30.7818,-81.5677x-38.0356,-77.9423x-45,-73.7237x-51.6219,-68.944x-57.8509,-63.6396x-63.6396,-57.8509x-68.944,-51.6219x-73.7237,-45x-77.9423,-38.0356x-81.5677,-30.7818x-84.5723,-23.2937x-86.9333,-15.6283x-88.6327,-7.84402x-89.6575,-1.65327e-14x-90,7.84402x-89.6575,15.6283x-88.6327,23.2937x-86.9333,30.7818x-84.5723,38.0356x-81.5677,45x-77.9423,51.6219x-73.7237,57.8509x-68.944,63.6396x-63.6396,68.944x-57.8509,73.7237x-51.6219,77.9423x-45,81.5677x-38.0356,84.5723x-30.7818,86.9333x-23.2937,88.6327x-15.6283,89.6575x-7.84402,90x-2.20436e-14
before_layer_gcode = ; Layer change to Layer [layer_num]\n; Z=[layer_z]\n
between_objects_gcode = 
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0
end_gcode = M104 S0 ; turn off hotend temperature\nM190 S0; turn off bed temperature\nG28 ; home \nM84     ; disable motors\n\n
extra_loading_move = -2
extruder_colour = #019B9B
extruder_offset = 0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_max_acceleration_e = 10000,5000
machine_max_acceleration_extruding = 1500,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_x = 9000,9000
machine_max_acceleration_y = 9000,9000
machine_max_acceleration_z = 9000,9000
machine_max_feedrate_e = 250,250
machine_max_feedrate_x = 1500,1500
machine_max_feedrate_y = 1500,1500
machine_max_feedrate_z = 1500,1500
machine_max_jerk_e = 2.5,2.5
machine_max_jerk_x = 9,9
machine_max_jerk_y = 9,9
machine_max_jerk_z = 9,9
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0
max_print_height = 196
min_layer_height = 0.1
nozzle_diameter = 0.4
parking_pos_retraction = 92
print_host = 
printer_model = 
printer_notes = 
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 1
retract_before_travel = 2
retract_before_wipe = 10%
retract_layer_change = 0
retract_length = 1.85
retract_length_toolchange = 10
retract_lift = 0.2
retract_lift_above = 0.4
retract_lift_below = 150
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
serial_port = 
serial_speed = 250000
silent_mode = 1
single_extruder_multi_material = 0
start_gcode = G28 ; home all axes\nM140 S[first_layer_bed_temperature] ; set bed final temp\nG1 X0 Y0 Z100 F4000 ; safe position\nG1 X-65 Y42 Z5 F4000 ; lift nozzle\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\nM104 S[first_layer_temperature] ; set extruder final temp\nM109 S[first_layer_temperature] ; wait for extruder final temp\nG1 X-67 Y40 Z0.3 F3000 ; move down\nG1 Z0.5; lift\nG92 E0\n{if perimeter_speed >= 100}M900 K0; Disable LINEAR_ADVANCE for speed's sake!\n{elsif perimeter_speed >= 65}M900 K0.2; reduced LINEAR_ADVANCE because of higher speeds\n{else}M900 K0.38; LINEAR_ADVANCE high quality preset\n{endif}
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0