new config for 0.5 nozzle and prusament petg black

PrusaSlicer/PrusaSlicer.ini

@@ -1,6 +1,6 @@
-# generated by PrusaSlicer 2.5.2 on 2023-06-19 at 18:14:34 UTC
+# generated by PrusaSlicer 2.5.0+linux-x64-GTK2 on 2023-07-15 at 15:41:15 UTC
 allow_ip_resolve = 1
-auto_toolbar_size = 100
+auto_toolbar_size = 96
 autocenter = 0
 background_processing = 0
 clear_undo_redo_stack_on_new_project = 1
@@ -37,13 +37,13 @@ use_custom_toolbar_size = 0
 use_free_camera = 0
 use_inches = 0
 use_perspective_camera = 0
-version = 2.5.2
+version = 2.5.0+linux-x64-GTK2
 version_check = 1
 version_online = 2.4.2
 version_online_seen = 2.4.2
 version_system_info_sent = 2.5.0+linux-x64-GTK2
 view_mode = expert
-window_mainframe = 0; 69; 5120; 1371; 1
+window_mainframe = 36; 24; 1330; 744; 1
 
 [filaments]
 Generic ABS = 1

PrusaSlicer/filament/PETG-prusament-black-test.ini

@@ -0,0 +1,57 @@
+# generated by PrusaSlicer 2.5.0+linux-x64-GTK2 on 2023-06-20 at 20:59:06 UTC
+bed_temperature = 70
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = 
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #000000
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 20
+filament_density = 1.18
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = "Noulei Silk PLA Filaments.\nPrint well on low temps <200°C, but black has far better strength and layer adhesion than the bright colours.\nSuccessfully tested filaments already testet on delta /w e3dv6/0.4:\n\n#24 Silk Black\n#11Silk Blue\n#14Silk Silver Blue\n\nnext ones to test out:\n#26 antique gold\n#9 red\n#4 white\npetg?"
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_type = PET
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 72
+first_layer_temperature = 245
+full_fan_speed_layer = 3
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+slowdown_below_layer_time = 8
+start_filament_gcode = "; Filament gcode\n"
+temperature = 245

PrusaSlicer/filament/PLA_Sunlu_Grasgruen.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.5.0+linux-x64-GTK2 on 2022-09-26 at 18:17:08 UTC
+# generated by PrusaSlicer 2.5.0+linux-x64-GTK2 on 2023-06-19 at 18:24:16 UTC
 bed_temperature = 60
 bridge_fan_speed = 100
 compatible_printers = 
@@ -6,7 +6,7 @@ compatible_printers_condition =
 compatible_prints = 
 compatible_prints_condition = 
 cooling = 1
-disable_fan_first_layers = 2
+disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
 extrusion_multiplier = 0.98
 fan_always_on = 1

PrusaSlicer/print/delta.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.5.0+linux-x64-GTK2 on 2023-03-31 at 21:06:44 UTC
+# generated by PrusaSlicer 2.5.0+linux-x64-GTK2 on 2023-06-20 at 20:29:40 UTC
 avoid_crossing_perimeters = 0
 avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonic
@@ -33,7 +33,7 @@ fill_pattern = rectilinear
 first_layer_acceleration = 0
 first_layer_acceleration_over_raft = 0
 first_layer_extrusion_width = 200%
-first_layer_height = 0.4
+first_layer_height = 0.3
 first_layer_speed = 35
 first_layer_speed_over_raft = 30
 fuzzy_skin = none
@@ -62,7 +62,7 @@ ironing_flowrate = 15%
 ironing_spacing = 0.1
 ironing_speed = 20
 ironing_type = topmost
-layer_height = 0.4
+layer_height = 0.3
 max_print_speed = 200
 max_volumetric_extrusion_rate_slope_negative = 0
 max_volumetric_extrusion_rate_slope_positive = 0
@@ -92,7 +92,7 @@ raft_layers = 0
 resolution = 0
 seam_position = rear
 single_extruder_multi_material_priming = 1
-skirt_distance = 4
+skirt_distance = 2
 skirt_height = 1
 skirts = 1
 slice_closing_radius = 0.049

PrusaSlicer/printer/delta.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.5.0+linux-x64-GTK2 on 2022-09-26 at 18:16:41 UTC
+# generated by PrusaSlicer 2.5.0+linux-x64-GTK2 on 2023-06-20 at 20:29:30 UTC
 bed_custom_model = 
 bed_custom_texture = 
 bed_shape = 89.6575x7.84402,88.6327x15.6283,86.9333x23.2937,84.5723x30.7818,81.5677x38.0356,77.9423x45,73.7237x51.6219,68.944x57.8509,63.6396x63.6396,57.8509x68.944,51.6219x73.7237,45x77.9423,38.0356x81.5677,30.7818x84.5723,23.2937x86.9333,15.6283x88.6327,7.84402x89.6575,5.51091e-15x90,-7.84402x89.6575,-15.6283x88.6327,-23.2937x86.9333,-30.7818x84.5723,-38.0356x81.5677,-45x77.9423,-51.6219x73.7237,-57.8509x68.944,-63.6396x63.6396,-68.944x57.8509,-73.7237x51.6219,-77.9423x45,-81.5677x38.0356,-84.5723x30.7818,-86.9333x23.2937,-88.6327x15.6283,-89.6575x7.84402,-90x1.10218e-14,-89.6575x-7.84402,-88.6327x-15.6283,-86.9333x-23.2937,-84.5723x-30.7818,-81.5677x-38.0356,-77.9423x-45,-73.7237x-51.6219,-68.944x-57.8509,-63.6396x-63.6396,-57.8509x-68.944,-51.6219x-73.7237,-45x-77.9423,-38.0356x-81.5677,-30.7818x-84.5723,-23.2937x-86.9333,-15.6283x-88.6327,-7.84402x-89.6575,-1.65327e-14x-90,7.84402x-89.6575,15.6283x-88.6327,23.2937x-86.9333,30.7818x-84.5723,38.0356x-81.5677,45x-77.9423,51.6219x-73.7237,57.8509x-68.944,63.6396x-63.6396,68.944x-57.8509,73.7237x-51.6219,77.9423x-45,81.5677x-38.0356,84.5723x-30.7818,86.9333x-23.2937,88.6327x-15.6283,89.6575x-7.84402,90x-2.20436e-14
@@ -10,7 +10,7 @@ cooling_tube_retraction = 91.5
 default_filament_profile = ""
 default_print_profile = 
 deretract_speed = 0
-end_gcode = M104 S0 ; turn off hotend temperature\nM190 S0; turn off bed temperature\nM106; hotend fan full blast\nG28; home \nM84; disable motors\nG4 S10; wait 10 seconds for hotend cooldown\n; play some tunes:\n;Mission Impossible\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2637 P75\nM300 S2793 P75\nM300 S2959 P75\nM300 S3135 P75\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S1864 P150\nM300 S0 P150\nM300 S2093 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S2793 P150\nM300 S0 P150\nM300 S2959 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S1864 P150\nM300 S0 P150\nM300 S2093 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S2793 P150\nM300 S0 P150\nM300 S2959 P150\nM300 S0 P150\nM300 S1864 P150\nM300 S3135 P150\nM300 S2349 P1200\nM300 S0 P75\nM300 S1864 P150\nM300 S3135 P150\nM300 S2217 P1200\nM300 S0 P75\nM300 S1864 P150\nM300 S3135 P150\nM300 S2093 P1200\nM300 S0 P150\nM300 S932 P150\nM300 S2093 P150\n; end of tune\nG4 S120; wait another 2 Minutes for hotend cooldown\nM107; hotend fan off
+end_gcode = M104 S0 ; turn off hotend temperature\nM190 S0; turn off bed temperature\nM106; hotend fan full blast\nG28; home \nM84; disable motors\nG4 S10; wait 10 seconds for hotend cooldown\n; play some tunes:\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2637 P75\nM300 S2793 P75\nM300 S2959 P75\nM300 S3135 P75\nM300 S3135 P150\n; end of tune\nG4 S120; wait another 2 Minutes for hotend cooldown\nM107; hotend fan off
 extra_loading_move = -2
 extruder_colour = #019B9B
 extruder_offset = 0x0
@@ -37,10 +37,10 @@ machine_max_jerk_y = 9,9
 machine_max_jerk_z = 9,9
 machine_min_extruding_rate = 0,0
 machine_min_travel_rate = 0,0
-max_layer_height = 0
+max_layer_height = 0.35
 max_print_height = 190
 min_layer_height = 0.1
-nozzle_diameter = 0.6
+nozzle_diameter = 0.5
 parking_pos_retraction = 92
 pause_print_gcode = M601
 print_host =