added prusaslicer config folder
This commit is contained in:
@@ -0,0 +1,55 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-08-16 at 00:56:16 UTC
|
||||
bed_temperature = 60
|
||||
bridge_fan_speed = 100
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
compatible_prints =
|
||||
compatible_prints_condition =
|
||||
cooling = 1
|
||||
disable_fan_first_layers = 3
|
||||
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
||||
extrusion_multiplier = 1
|
||||
fan_always_on = 0
|
||||
fan_below_layer_time = 60
|
||||
filament_colour = #29B2B2
|
||||
filament_cooling_final_speed = 3.4
|
||||
filament_cooling_initial_speed = 2.2
|
||||
filament_cooling_moves = 4
|
||||
filament_cost = 0
|
||||
filament_density = 0
|
||||
filament_deretract_speed = nil
|
||||
filament_diameter = 1.75
|
||||
filament_load_time = 0
|
||||
filament_loading_speed = 28
|
||||
filament_loading_speed_start = 3
|
||||
filament_max_volumetric_speed = 0
|
||||
filament_minimal_purge_on_wipe_tower = 15
|
||||
filament_notes = ""
|
||||
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
||||
filament_retract_before_travel = nil
|
||||
filament_retract_before_wipe = nil
|
||||
filament_retract_layer_change = nil
|
||||
filament_retract_length = nil
|
||||
filament_retract_lift = nil
|
||||
filament_retract_lift_above = nil
|
||||
filament_retract_lift_below = nil
|
||||
filament_retract_restart_extra = nil
|
||||
filament_retract_speed = nil
|
||||
filament_settings_id = ""
|
||||
filament_soluble = 0
|
||||
filament_toolchange_delay = 0
|
||||
filament_type = PLA
|
||||
filament_unload_time = 0
|
||||
filament_unloading_speed = 90
|
||||
filament_unloading_speed_start = 100
|
||||
filament_vendor = (Unknown)
|
||||
filament_wipe = nil
|
||||
first_layer_bed_temperature = 60
|
||||
first_layer_temperature = 200
|
||||
inherits =
|
||||
max_fan_speed = 100
|
||||
min_fan_speed = 35
|
||||
min_print_speed = 10
|
||||
slowdown_below_layer_time = 5
|
||||
start_filament_gcode = "; Filament gcode\n"
|
||||
temperature = 200
|
||||
@@ -0,0 +1,114 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-08-16 at 00:56:42 UTC
|
||||
avoid_crossing_perimeters = 0
|
||||
bottom_fill_pattern = rectilinear
|
||||
bottom_solid_layers = 3
|
||||
bottom_solid_min_thickness = 0
|
||||
bridge_acceleration = 0
|
||||
bridge_angle = 0
|
||||
bridge_flow_ratio = 1
|
||||
bridge_speed = 60
|
||||
brim_width = 0
|
||||
clip_multipart_objects = 1
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
complete_objects = 0
|
||||
default_acceleration = 0
|
||||
dont_support_bridges = 1
|
||||
draft_shield = 0
|
||||
elefant_foot_compensation = 0.2
|
||||
ensure_vertical_shell_thickness = 0
|
||||
external_perimeter_extrusion_width = 0.45
|
||||
external_perimeter_speed = 50%
|
||||
external_perimeters_first = 0
|
||||
extra_perimeters = 1
|
||||
extruder_clearance_height = 20
|
||||
extruder_clearance_radius = 20
|
||||
extrusion_width = 0.45
|
||||
fill_angle = 45
|
||||
fill_density = 20%
|
||||
fill_pattern = gyroid
|
||||
first_layer_acceleration = 0
|
||||
first_layer_extrusion_width = 0.42
|
||||
first_layer_height = 0.35
|
||||
first_layer_speed = 30
|
||||
gap_fill_speed = 20
|
||||
gcode_comments = 0
|
||||
gcode_label_objects = 0
|
||||
infill_acceleration = 0
|
||||
infill_every_layers = 1
|
||||
infill_extruder = 1
|
||||
infill_extrusion_width = 0.45
|
||||
infill_first = 0
|
||||
infill_only_where_needed = 0
|
||||
infill_overlap = 25%
|
||||
infill_speed = 80
|
||||
inherits =
|
||||
interface_shells = 0
|
||||
layer_height = 0.3
|
||||
max_print_speed = 80
|
||||
max_volumetric_speed = 0
|
||||
min_skirt_length = 0
|
||||
notes =
|
||||
only_retract_when_crossing_perimeters = 1
|
||||
ooze_prevention = 0
|
||||
output_filename_format = [input_filename_base].gcode
|
||||
overhangs = 1
|
||||
perimeter_acceleration = 0
|
||||
perimeter_extruder = 1
|
||||
perimeter_extrusion_width = 0.45
|
||||
perimeter_speed = 60
|
||||
perimeters = 3
|
||||
post_process =
|
||||
print_settings_id =
|
||||
raft_layers = 0
|
||||
resolution = 0
|
||||
seam_position = aligned
|
||||
single_extruder_multi_material_priming = 1
|
||||
skirt_distance = 6
|
||||
skirt_height = 1
|
||||
skirts = 1
|
||||
slice_closing_radius = 0.049
|
||||
small_perimeter_speed = 15
|
||||
solid_infill_below_area = 70
|
||||
solid_infill_every_layers = 0
|
||||
solid_infill_extruder = 1
|
||||
solid_infill_extrusion_width = 0.45
|
||||
solid_infill_speed = 20
|
||||
spiral_vase = 0
|
||||
standby_temperature_delta = -5
|
||||
support_material = 0
|
||||
support_material_angle = 0
|
||||
support_material_auto = 1
|
||||
support_material_buildplate_only = 0
|
||||
support_material_contact_distance = 0.2
|
||||
support_material_enforce_layers = 0
|
||||
support_material_extruder = 1
|
||||
support_material_extrusion_width = 0.35
|
||||
support_material_interface_contact_loops = 0
|
||||
support_material_interface_extruder = 1
|
||||
support_material_interface_layers = 3
|
||||
support_material_interface_spacing = 0
|
||||
support_material_interface_speed = 100%
|
||||
support_material_pattern = rectilinear
|
||||
support_material_spacing = 2.5
|
||||
support_material_speed = 60
|
||||
support_material_synchronize_layers = 0
|
||||
support_material_threshold = 0
|
||||
support_material_with_sheath = 1
|
||||
support_material_xy_spacing = 50%
|
||||
thin_walls = 1
|
||||
threads = 8
|
||||
top_fill_pattern = rectilinear
|
||||
top_infill_extrusion_width = 0.4
|
||||
top_solid_infill_speed = 15
|
||||
top_solid_layers = 3
|
||||
top_solid_min_thickness = 0
|
||||
travel_speed = 130
|
||||
wipe_tower = 0
|
||||
wipe_tower_bridging = 10
|
||||
wipe_tower_no_sparse_layers = 0
|
||||
wipe_tower_rotation_angle = 0
|
||||
wipe_tower_width = 60
|
||||
wipe_tower_x = 180
|
||||
wipe_tower_y = 140
|
||||
xy_size_compensation = 0
|
||||
@@ -0,0 +1,75 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-08-16 at 00:56:16 UTC
|
||||
bed_custom_model =
|
||||
bed_custom_texture =
|
||||
bed_shape = 99.6195x8.71557,98.4808x17.3648,96.5926x25.8819,93.9693x34.202,90.6308x42.2618,86.6025x50,81.9152x57.3576,76.6044x64.2788,70.7107x70.7107,64.2788x76.6044,57.3576x81.9152,50x86.6025,42.2618x90.6308,34.202x93.9693,25.8819x96.5926,17.3648x98.4808,8.71557x99.6195,6.12323e-15x100,-8.71557x99.6195,-17.3648x98.4808,-25.8819x96.5926,-34.202x93.9693,-42.2618x90.6308,-50x86.6025,-57.3576x81.9152,-64.2788x76.6044,-70.7107x70.7107,-76.6044x64.2788,-81.9152x57.3576,-86.6025x50,-90.6308x42.2618,-93.9693x34.202,-96.5926x25.8819,-98.4808x17.3648,-99.6195x8.71557,-100x1.22465e-14,-99.6195x-8.71557,-98.4808x-17.3648,-96.5926x-25.8819,-93.9693x-34.202,-90.6308x-42.2618,-86.6025x-50,-81.9152x-57.3576,-76.6044x-64.2788,-70.7107x-70.7107,-64.2788x-76.6044,-57.3576x-81.9152,-50x-86.6025,-42.2618x-90.6308,-34.202x-93.9693,-25.8819x-96.5926,-17.3648x-98.4808,-8.71557x-99.6195,-1.83697e-14x-100,8.71557x-99.6195,17.3648x-98.4808,25.8819x-96.5926,34.202x-93.9693,42.2618x-90.6308,50x-86.6025,57.3576x-81.9152,64.2788x-76.6044,70.7107x-70.7107,76.6044x-64.2788,81.9152x-57.3576,86.6025x-50,90.6308x-42.2618,93.9693x-34.202,96.5926x-25.8819,98.4808x-17.3648,99.6195x-8.71557,100x-2.44929e-14
|
||||
before_layer_gcode =
|
||||
between_objects_gcode =
|
||||
cooling_tube_length = 5
|
||||
cooling_tube_retraction = 91.5
|
||||
default_filament_profile = ""
|
||||
default_print_profile =
|
||||
deretract_speed = 0
|
||||
end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n
|
||||
extra_loading_move = -2
|
||||
extruder_colour = ""
|
||||
extruder_offset = 0x0
|
||||
gcode_flavor = marlin
|
||||
high_current_on_filament_swap = 0
|
||||
host_type = octoprint
|
||||
inherits =
|
||||
layer_gcode =
|
||||
machine_max_acceleration_e = 10000,5000
|
||||
machine_max_acceleration_extruding = 1500,1250
|
||||
machine_max_acceleration_retracting = 1500,1250
|
||||
machine_max_acceleration_x = 9000,1000
|
||||
machine_max_acceleration_y = 9000,1000
|
||||
machine_max_acceleration_z = 500,200
|
||||
machine_max_feedrate_e = 120,120
|
||||
machine_max_feedrate_x = 500,200
|
||||
machine_max_feedrate_y = 500,200
|
||||
machine_max_feedrate_z = 12,12
|
||||
machine_max_jerk_e = 2.5,2.5
|
||||
machine_max_jerk_x = 10,10
|
||||
machine_max_jerk_y = 10,10
|
||||
machine_max_jerk_z = 0.2,0.4
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
max_layer_height = 0
|
||||
max_print_height = 200
|
||||
min_layer_height = 0.07
|
||||
nozzle_diameter = 0.4
|
||||
parking_pos_retraction = 92
|
||||
print_host =
|
||||
printer_model =
|
||||
printer_notes =
|
||||
printer_settings_id =
|
||||
printer_technology = FFF
|
||||
printer_variant =
|
||||
printer_vendor =
|
||||
printhost_apikey =
|
||||
printhost_cafile =
|
||||
remaining_times = 0
|
||||
retract_before_travel = 2
|
||||
retract_before_wipe = 0%
|
||||
retract_layer_change = 0
|
||||
retract_length = 2
|
||||
retract_length_toolchange = 10
|
||||
retract_lift = 0
|
||||
retract_lift_above = 0
|
||||
retract_lift_below = 0
|
||||
retract_restart_extra = 0
|
||||
retract_restart_extra_toolchange = 0
|
||||
retract_speed = 40
|
||||
serial_port =
|
||||
serial_speed = 250000
|
||||
silent_mode = 1
|
||||
single_extruder_multi_material = 0
|
||||
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
|
||||
thumbnails =
|
||||
toolchange_gcode =
|
||||
use_firmware_retraction = 0
|
||||
use_relative_e_distances = 0
|
||||
use_volumetric_e = 0
|
||||
variable_layer_height = 1
|
||||
wipe = 0
|
||||
z_offset = 0
|
||||
@@ -0,0 +1,19 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-09-06 at 20:59:15 UTC
|
||||
|
||||
[snapshot]
|
||||
id = 20200906T205915Z
|
||||
time_captured = 20200906T205915Z
|
||||
slic3r_version_captured = 2.2.0+linux-x64
|
||||
comment =
|
||||
reason = upgrade
|
||||
|
||||
[presets]
|
||||
print = delta
|
||||
filament = delta
|
||||
printer = delta
|
||||
|
||||
[Vendor:PrusaResearch]
|
||||
version = 1.1.2
|
||||
min_slic3r_version = 2.2.0-alpha3
|
||||
max_slic3r_version = 2147483647.2147483647.2147483647
|
||||
model_MINI = 0.25;0.4;0.6
|
||||
+4480
File diff suppressed because it is too large
Load Diff
+55
@@ -0,0 +1,55 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-12 at 05:06:14 UTC
|
||||
bed_temperature = 55
|
||||
bridge_fan_speed = 100
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
compatible_prints =
|
||||
compatible_prints_condition =
|
||||
cooling = 1
|
||||
disable_fan_first_layers = 1
|
||||
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
||||
extrusion_multiplier = 0.95
|
||||
fan_always_on = 1
|
||||
fan_below_layer_time = 60
|
||||
filament_colour = #6432E8
|
||||
filament_cooling_final_speed = 3.4
|
||||
filament_cooling_initial_speed = 2.2
|
||||
filament_cooling_moves = 4
|
||||
filament_cost = 20
|
||||
filament_density = 0
|
||||
filament_deretract_speed = nil
|
||||
filament_diameter = 1.75
|
||||
filament_load_time = 0
|
||||
filament_loading_speed = 28
|
||||
filament_loading_speed_start = 3
|
||||
filament_max_volumetric_speed = 0
|
||||
filament_minimal_purge_on_wipe_tower = 15
|
||||
filament_notes = ""
|
||||
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
||||
filament_retract_before_travel = nil
|
||||
filament_retract_before_wipe = nil
|
||||
filament_retract_layer_change = nil
|
||||
filament_retract_length = nil
|
||||
filament_retract_lift = nil
|
||||
filament_retract_lift_above = nil
|
||||
filament_retract_lift_below = nil
|
||||
filament_retract_restart_extra = nil
|
||||
filament_retract_speed = nil
|
||||
filament_settings_id = ""
|
||||
filament_soluble = 0
|
||||
filament_toolchange_delay = 0
|
||||
filament_type = PLA
|
||||
filament_unload_time = 0
|
||||
filament_unloading_speed = 90
|
||||
filament_unloading_speed_start = 100
|
||||
filament_vendor = (Unknown)
|
||||
filament_wipe = nil
|
||||
first_layer_bed_temperature = 55
|
||||
first_layer_temperature = 192
|
||||
inherits =
|
||||
max_fan_speed = 100
|
||||
min_fan_speed = 40
|
||||
min_print_speed = 10
|
||||
slowdown_below_layer_time = 8
|
||||
start_filament_gcode = "; Filament gcode\n"
|
||||
temperature = 190
|
||||
@@ -0,0 +1,55 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-09-24 at 14:30:47 UTC
|
||||
bed_temperature = 60
|
||||
bridge_fan_speed = 100
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
compatible_prints =
|
||||
compatible_prints_condition =
|
||||
cooling = 1
|
||||
disable_fan_first_layers = 3
|
||||
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
||||
extrusion_multiplier = 1
|
||||
fan_always_on = 1
|
||||
fan_below_layer_time = 90
|
||||
filament_colour = #29B2B2
|
||||
filament_cooling_final_speed = 3.4
|
||||
filament_cooling_initial_speed = 2.2
|
||||
filament_cooling_moves = 4
|
||||
filament_cost = 20
|
||||
filament_density = 0
|
||||
filament_deretract_speed = nil
|
||||
filament_diameter = 1.75
|
||||
filament_load_time = 0
|
||||
filament_loading_speed = 28
|
||||
filament_loading_speed_start = 3
|
||||
filament_max_volumetric_speed = 0
|
||||
filament_minimal_purge_on_wipe_tower = 15
|
||||
filament_notes = ""
|
||||
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
||||
filament_retract_before_travel = nil
|
||||
filament_retract_before_wipe = nil
|
||||
filament_retract_layer_change = nil
|
||||
filament_retract_length = nil
|
||||
filament_retract_lift = nil
|
||||
filament_retract_lift_above = nil
|
||||
filament_retract_lift_below = nil
|
||||
filament_retract_restart_extra = nil
|
||||
filament_retract_speed = nil
|
||||
filament_settings_id = ""
|
||||
filament_soluble = 0
|
||||
filament_toolchange_delay = 0
|
||||
filament_type = PLA
|
||||
filament_unload_time = 0
|
||||
filament_unloading_speed = 90
|
||||
filament_unloading_speed_start = 100
|
||||
filament_vendor = (Unknown)
|
||||
filament_wipe = nil
|
||||
first_layer_bed_temperature = 62
|
||||
first_layer_temperature = 195
|
||||
inherits =
|
||||
max_fan_speed = 100
|
||||
min_fan_speed = 100
|
||||
min_print_speed = 10
|
||||
slowdown_below_layer_time = 5
|
||||
start_filament_gcode = "; Filament gcode\n"
|
||||
temperature = 195
|
||||
@@ -0,0 +1,114 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-09 at 01:57:43 UTC
|
||||
avoid_crossing_perimeters = 0
|
||||
bottom_fill_pattern = rectilinear
|
||||
bottom_solid_layers = 3
|
||||
bottom_solid_min_thickness = 0
|
||||
bridge_acceleration = 0
|
||||
bridge_angle = 0
|
||||
bridge_flow_ratio = 0.91
|
||||
bridge_speed = 60
|
||||
brim_width = 0
|
||||
clip_multipart_objects = 1
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
complete_objects = 0
|
||||
default_acceleration = 0
|
||||
dont_support_bridges = 1
|
||||
draft_shield = 0
|
||||
elefant_foot_compensation = 0.1
|
||||
ensure_vertical_shell_thickness = 1
|
||||
external_perimeter_extrusion_width = 0.42
|
||||
external_perimeter_speed = 30
|
||||
external_perimeters_first = 0
|
||||
extra_perimeters = 1
|
||||
extruder_clearance_height = 20
|
||||
extruder_clearance_radius = 20
|
||||
extrusion_width = 0.44
|
||||
fill_angle = 45
|
||||
fill_density = 20%
|
||||
fill_pattern = cubic
|
||||
first_layer_acceleration = 0
|
||||
first_layer_extrusion_width = 0.44
|
||||
first_layer_height = 0.3
|
||||
first_layer_speed = 20
|
||||
gap_fill_speed = 20
|
||||
gcode_comments = 0
|
||||
gcode_label_objects = 0
|
||||
infill_acceleration = 0
|
||||
infill_every_layers = 1
|
||||
infill_extruder = 1
|
||||
infill_extrusion_width = 0.44
|
||||
infill_first = 0
|
||||
infill_only_where_needed = 0
|
||||
infill_overlap = 30%
|
||||
infill_speed = 80
|
||||
inherits =
|
||||
interface_shells = 0
|
||||
layer_height = 0.2
|
||||
max_print_speed = 100
|
||||
max_volumetric_speed = 0
|
||||
min_skirt_length = 10
|
||||
notes =
|
||||
only_retract_when_crossing_perimeters = 0
|
||||
ooze_prevention = 0
|
||||
output_filename_format = [input_filename_base].gcode
|
||||
overhangs = 1
|
||||
perimeter_acceleration = 0
|
||||
perimeter_extruder = 1
|
||||
perimeter_extrusion_width = 0.44
|
||||
perimeter_speed = 60
|
||||
perimeters = 3
|
||||
post_process =
|
||||
print_settings_id =
|
||||
raft_layers = 0
|
||||
resolution = 0
|
||||
seam_position = aligned
|
||||
single_extruder_multi_material_priming = 1
|
||||
skirt_distance = 6
|
||||
skirt_height = 1
|
||||
skirts = 1
|
||||
slice_closing_radius = 0.049
|
||||
small_perimeter_speed = 50%
|
||||
solid_infill_below_area = 70
|
||||
solid_infill_every_layers = 0
|
||||
solid_infill_extruder = 1
|
||||
solid_infill_extrusion_width = 0.44
|
||||
solid_infill_speed = 50
|
||||
spiral_vase = 0
|
||||
standby_temperature_delta = -5
|
||||
support_material = 0
|
||||
support_material_angle = 0
|
||||
support_material_auto = 1
|
||||
support_material_buildplate_only = 1
|
||||
support_material_contact_distance = 0.2
|
||||
support_material_enforce_layers = 0
|
||||
support_material_extruder = 1
|
||||
support_material_extrusion_width = 0.45
|
||||
support_material_interface_contact_loops = 0
|
||||
support_material_interface_extruder = 1
|
||||
support_material_interface_layers = 3
|
||||
support_material_interface_spacing = 0
|
||||
support_material_interface_speed = 100%
|
||||
support_material_pattern = rectilinear
|
||||
support_material_spacing = 1.5
|
||||
support_material_speed = 50
|
||||
support_material_synchronize_layers = 0
|
||||
support_material_threshold = 20
|
||||
support_material_with_sheath = 1
|
||||
support_material_xy_spacing = 50%
|
||||
thin_walls = 1
|
||||
threads = 8
|
||||
top_fill_pattern = rectilinear
|
||||
top_infill_extrusion_width = 0.44
|
||||
top_solid_infill_speed = 20
|
||||
top_solid_layers = 3
|
||||
top_solid_min_thickness = 0
|
||||
travel_speed = 250
|
||||
wipe_tower = 0
|
||||
wipe_tower_bridging = 10
|
||||
wipe_tower_no_sparse_layers = 0
|
||||
wipe_tower_rotation_angle = 0
|
||||
wipe_tower_width = 60
|
||||
wipe_tower_x = 180
|
||||
wipe_tower_y = 140
|
||||
xy_size_compensation = 0
|
||||
@@ -0,0 +1,114 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-09 at 15:48:42 UTC
|
||||
avoid_crossing_perimeters = 0
|
||||
bottom_fill_pattern = rectilinear
|
||||
bottom_solid_layers = 3
|
||||
bottom_solid_min_thickness = 0
|
||||
bridge_acceleration = 0
|
||||
bridge_angle = 0
|
||||
bridge_flow_ratio = 0.91
|
||||
bridge_speed = 100
|
||||
brim_width = 0
|
||||
clip_multipart_objects = 1
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
complete_objects = 0
|
||||
default_acceleration = 0
|
||||
dont_support_bridges = 1
|
||||
draft_shield = 0
|
||||
elefant_foot_compensation = 0.1
|
||||
ensure_vertical_shell_thickness = 1
|
||||
external_perimeter_extrusion_width = 0.42
|
||||
external_perimeter_speed = 100
|
||||
external_perimeters_first = 0
|
||||
extra_perimeters = 1
|
||||
extruder_clearance_height = 20
|
||||
extruder_clearance_radius = 20
|
||||
extrusion_width = 0.44
|
||||
fill_angle = 45
|
||||
fill_density = 15%
|
||||
fill_pattern = cubic
|
||||
first_layer_acceleration = 0
|
||||
first_layer_extrusion_width = 0.44
|
||||
first_layer_height = 0.3
|
||||
first_layer_speed = 40
|
||||
gap_fill_speed = 100
|
||||
gcode_comments = 0
|
||||
gcode_label_objects = 0
|
||||
infill_acceleration = 0
|
||||
infill_every_layers = 1
|
||||
infill_extruder = 1
|
||||
infill_extrusion_width = 0.44
|
||||
infill_first = 0
|
||||
infill_only_where_needed = 0
|
||||
infill_overlap = 30%
|
||||
infill_speed = 100
|
||||
inherits =
|
||||
interface_shells = 0
|
||||
layer_height = 0.2
|
||||
max_print_speed = 200
|
||||
max_volumetric_speed = 0
|
||||
min_skirt_length = 10
|
||||
notes =
|
||||
only_retract_when_crossing_perimeters = 0
|
||||
ooze_prevention = 0
|
||||
output_filename_format = [input_filename_base].gcode
|
||||
overhangs = 1
|
||||
perimeter_acceleration = 0
|
||||
perimeter_extruder = 1
|
||||
perimeter_extrusion_width = 0.44
|
||||
perimeter_speed = 100
|
||||
perimeters = 3
|
||||
post_process =
|
||||
print_settings_id =
|
||||
raft_layers = 0
|
||||
resolution = 0
|
||||
seam_position = aligned
|
||||
single_extruder_multi_material_priming = 1
|
||||
skirt_distance = 6
|
||||
skirt_height = 1
|
||||
skirts = 1
|
||||
slice_closing_radius = 0.049
|
||||
small_perimeter_speed = 100
|
||||
solid_infill_below_area = 70
|
||||
solid_infill_every_layers = 0
|
||||
solid_infill_extruder = 1
|
||||
solid_infill_extrusion_width = 0.44
|
||||
solid_infill_speed = 100
|
||||
spiral_vase = 0
|
||||
standby_temperature_delta = -5
|
||||
support_material = 0
|
||||
support_material_angle = 0
|
||||
support_material_auto = 1
|
||||
support_material_buildplate_only = 1
|
||||
support_material_contact_distance = 0.2
|
||||
support_material_enforce_layers = 0
|
||||
support_material_extruder = 1
|
||||
support_material_extrusion_width = 0.45
|
||||
support_material_interface_contact_loops = 0
|
||||
support_material_interface_extruder = 1
|
||||
support_material_interface_layers = 3
|
||||
support_material_interface_spacing = 0
|
||||
support_material_interface_speed = 100%
|
||||
support_material_pattern = rectilinear
|
||||
support_material_spacing = 1.5
|
||||
support_material_speed = 100
|
||||
support_material_synchronize_layers = 0
|
||||
support_material_threshold = 20
|
||||
support_material_with_sheath = 1
|
||||
support_material_xy_spacing = 50%
|
||||
thin_walls = 1
|
||||
threads = 8
|
||||
top_fill_pattern = rectilinear
|
||||
top_infill_extrusion_width = 0.44
|
||||
top_solid_infill_speed = 100
|
||||
top_solid_layers = 3
|
||||
top_solid_min_thickness = 0
|
||||
travel_speed = 250
|
||||
wipe_tower = 0
|
||||
wipe_tower_bridging = 10
|
||||
wipe_tower_no_sparse_layers = 0
|
||||
wipe_tower_rotation_angle = 0
|
||||
wipe_tower_width = 60
|
||||
wipe_tower_x = 180
|
||||
wipe_tower_y = 140
|
||||
xy_size_compensation = 0
|
||||
@@ -0,0 +1,75 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-11 at 19:45:55 UTC
|
||||
bed_custom_model =
|
||||
bed_custom_texture =
|
||||
bed_shape = 89.6575x7.84402,88.6327x15.6283,86.9333x23.2937,84.5723x30.7818,81.5677x38.0356,77.9423x45,73.7237x51.6219,68.944x57.8509,63.6396x63.6396,57.8509x68.944,51.6219x73.7237,45x77.9423,38.0356x81.5677,30.7818x84.5723,23.2937x86.9333,15.6283x88.6327,7.84402x89.6575,5.51091e-15x90,-7.84402x89.6575,-15.6283x88.6327,-23.2937x86.9333,-30.7818x84.5723,-38.0356x81.5677,-45x77.9423,-51.6219x73.7237,-57.8509x68.944,-63.6396x63.6396,-68.944x57.8509,-73.7237x51.6219,-77.9423x45,-81.5677x38.0356,-84.5723x30.7818,-86.9333x23.2937,-88.6327x15.6283,-89.6575x7.84402,-90x1.10218e-14,-89.6575x-7.84402,-88.6327x-15.6283,-86.9333x-23.2937,-84.5723x-30.7818,-81.5677x-38.0356,-77.9423x-45,-73.7237x-51.6219,-68.944x-57.8509,-63.6396x-63.6396,-57.8509x-68.944,-51.6219x-73.7237,-45x-77.9423,-38.0356x-81.5677,-30.7818x-84.5723,-23.2937x-86.9333,-15.6283x-88.6327,-7.84402x-89.6575,-1.65327e-14x-90,7.84402x-89.6575,15.6283x-88.6327,23.2937x-86.9333,30.7818x-84.5723,38.0356x-81.5677,45x-77.9423,51.6219x-73.7237,57.8509x-68.944,63.6396x-63.6396,68.944x-57.8509,73.7237x-51.6219,77.9423x-45,81.5677x-38.0356,84.5723x-30.7818,86.9333x-23.2937,88.6327x-15.6283,89.6575x-7.84402,90x-2.20436e-14
|
||||
before_layer_gcode = ; Layer change to Layer [layer_num]\n; Z=[layer_z]\n
|
||||
between_objects_gcode =
|
||||
cooling_tube_length = 5
|
||||
cooling_tube_retraction = 91.5
|
||||
default_filament_profile = ""
|
||||
default_print_profile =
|
||||
deretract_speed = 0
|
||||
end_gcode = M104 S0 ; turn off hotend temperature\nM190 S0; turn off bed temperature\nG28 ; home \nM84 ; disable motors\n\n
|
||||
extra_loading_move = -2
|
||||
extruder_colour = #019B9B
|
||||
extruder_offset = 0x0
|
||||
gcode_flavor = marlin
|
||||
high_current_on_filament_swap = 0
|
||||
host_type = octoprint
|
||||
inherits =
|
||||
layer_gcode =
|
||||
machine_max_acceleration_e = 10000,5000
|
||||
machine_max_acceleration_extruding = 1500,1250
|
||||
machine_max_acceleration_retracting = 1500,1250
|
||||
machine_max_acceleration_x = 9000,9000
|
||||
machine_max_acceleration_y = 9000,9000
|
||||
machine_max_acceleration_z = 9000,9000
|
||||
machine_max_feedrate_e = 250,250
|
||||
machine_max_feedrate_x = 1500,1500
|
||||
machine_max_feedrate_y = 1500,1500
|
||||
machine_max_feedrate_z = 1500,1500
|
||||
machine_max_jerk_e = 2.5,2.5
|
||||
machine_max_jerk_x = 9,9
|
||||
machine_max_jerk_y = 9,9
|
||||
machine_max_jerk_z = 9,9
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
max_layer_height = 0
|
||||
max_print_height = 196
|
||||
min_layer_height = 0.1
|
||||
nozzle_diameter = 0.4
|
||||
parking_pos_retraction = 92
|
||||
print_host =
|
||||
printer_model =
|
||||
printer_notes =
|
||||
printer_settings_id =
|
||||
printer_technology = FFF
|
||||
printer_variant =
|
||||
printer_vendor =
|
||||
printhost_apikey =
|
||||
printhost_cafile =
|
||||
remaining_times = 1
|
||||
retract_before_travel = 2
|
||||
retract_before_wipe = 10%
|
||||
retract_layer_change = 0
|
||||
retract_length = 1.85
|
||||
retract_length_toolchange = 10
|
||||
retract_lift = 0.2
|
||||
retract_lift_above = 0.4
|
||||
retract_lift_below = 150
|
||||
retract_restart_extra = 0
|
||||
retract_restart_extra_toolchange = 0
|
||||
retract_speed = 30
|
||||
serial_port =
|
||||
serial_speed = 250000
|
||||
silent_mode = 1
|
||||
single_extruder_multi_material = 0
|
||||
start_gcode = G28 ; home all axes\nM140 S[first_layer_bed_temperature] ; set bed final temp\nG1 X0 Y0 Z100 F4000 ; safe position\nG1 X-65 Y42 Z5 F4000 ; lift nozzle\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\nM104 S[first_layer_temperature] ; set extruder final temp\nM109 S[first_layer_temperature] ; wait for extruder final temp\nG1 X-67 Y40 Z0.3 F3000 ; move down\nG1 Z0.5; lift\nG92 E0\n{if perimeter_speed >= 100}M900 K0; Disable LINEAR_ADVANCE for speed's sake!\n{elsif perimeter_speed >= 65}M900 K0.2; reduced LINEAR_ADVANCE because of higher speeds\n{else}M900 K0.38; LINEAR_ADVANCE high quality preset\n{endif}
|
||||
thumbnails =
|
||||
toolchange_gcode =
|
||||
use_firmware_retraction = 0
|
||||
use_relative_e_distances = 0
|
||||
use_volumetric_e = 0
|
||||
variable_layer_height = 1
|
||||
wipe = 0
|
||||
z_offset = 0
|
||||
@@ -0,0 +1,19 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-12 at 19:12:58 UTC
|
||||
|
||||
[snapshot]
|
||||
id = 20201012T191258Z
|
||||
time_captured = 20201012T191258Z
|
||||
slic3r_version_captured = 2.2.0+linux-x64
|
||||
comment =
|
||||
reason = upgrade
|
||||
|
||||
[presets]
|
||||
print = delta
|
||||
filament = PLA_Noulei-Silk BlueSilver_Silk Blue
|
||||
printer = delta
|
||||
|
||||
[Vendor:PrusaResearch]
|
||||
version = 1.1.8
|
||||
min_slic3r_version = 2.2.0-alpha3
|
||||
max_slic3r_version = 2147483647.2147483647.2147483647
|
||||
model_MINI = 0.25;0.4;0.6
|
||||
+5085
File diff suppressed because it is too large
Load Diff
@@ -0,0 +1,55 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-15 at 21:23:23 UTC
|
||||
bed_temperature = 55
|
||||
bridge_fan_speed = 100
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
compatible_prints =
|
||||
compatible_prints_condition =
|
||||
cooling = 1
|
||||
disable_fan_first_layers = 1
|
||||
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
||||
extrusion_multiplier = 0.95
|
||||
fan_always_on = 1
|
||||
fan_below_layer_time = 60
|
||||
filament_colour = #000000
|
||||
filament_cooling_final_speed = 3.4
|
||||
filament_cooling_initial_speed = 2.2
|
||||
filament_cooling_moves = 4
|
||||
filament_cost = 20
|
||||
filament_density = 1.18
|
||||
filament_deretract_speed = nil
|
||||
filament_diameter = 1.75
|
||||
filament_load_time = 0
|
||||
filament_loading_speed = 28
|
||||
filament_loading_speed_start = 3
|
||||
filament_max_volumetric_speed = 0
|
||||
filament_minimal_purge_on_wipe_tower = 15
|
||||
filament_notes = "Noulei Silk PLA Filaments.\nPrint well on low temps <200°C, but black has far better strength and layer adhesion than the bright colours.\nSuccessfully tested filaments already testet on delta /w e3dv6/0.4:\n\n#24 Silk Black\n#11Silk Blue\n#14Silk Silver Blue\n\nnext ones to test out:\n#26 antique gold\n#9 red\n#4 white\npetg?"
|
||||
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
||||
filament_retract_before_travel = nil
|
||||
filament_retract_before_wipe = nil
|
||||
filament_retract_layer_change = nil
|
||||
filament_retract_length = nil
|
||||
filament_retract_lift = nil
|
||||
filament_retract_lift_above = nil
|
||||
filament_retract_lift_below = nil
|
||||
filament_retract_restart_extra = nil
|
||||
filament_retract_speed = nil
|
||||
filament_settings_id = ""
|
||||
filament_soluble = 0
|
||||
filament_toolchange_delay = 0
|
||||
filament_type = PLA
|
||||
filament_unload_time = 0
|
||||
filament_unloading_speed = 90
|
||||
filament_unloading_speed_start = 100
|
||||
filament_vendor = (Unknown)
|
||||
filament_wipe = nil
|
||||
first_layer_bed_temperature = 55
|
||||
first_layer_temperature = 192
|
||||
inherits =
|
||||
max_fan_speed = 100
|
||||
min_fan_speed = 40
|
||||
min_print_speed = 10
|
||||
slowdown_below_layer_time = 8
|
||||
start_filament_gcode = "; Filament gcode\n"
|
||||
temperature = 190
|
||||
@@ -0,0 +1,114 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-18 at 13:56:15 UTC
|
||||
avoid_crossing_perimeters = 0
|
||||
bottom_fill_pattern = rectilinear
|
||||
bottom_solid_layers = 3
|
||||
bottom_solid_min_thickness = 0
|
||||
bridge_acceleration = 0
|
||||
bridge_angle = 0
|
||||
bridge_flow_ratio = 0.91
|
||||
bridge_speed = 60
|
||||
brim_width = 0
|
||||
clip_multipart_objects = 1
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
complete_objects = 0
|
||||
default_acceleration = 0
|
||||
dont_support_bridges = 1
|
||||
draft_shield = 0
|
||||
elefant_foot_compensation = 0.1
|
||||
ensure_vertical_shell_thickness = 1
|
||||
external_perimeter_extrusion_width = 0.42
|
||||
external_perimeter_speed = 30
|
||||
external_perimeters_first = 0
|
||||
extra_perimeters = 1
|
||||
extruder_clearance_height = 20
|
||||
extruder_clearance_radius = 20
|
||||
extrusion_width = 0.44
|
||||
fill_angle = 45
|
||||
fill_density = 20%
|
||||
fill_pattern = gyroid
|
||||
first_layer_acceleration = 0
|
||||
first_layer_extrusion_width = 0.44
|
||||
first_layer_height = 0.3
|
||||
first_layer_speed = 20
|
||||
gap_fill_speed = 20
|
||||
gcode_comments = 0
|
||||
gcode_label_objects = 0
|
||||
infill_acceleration = 0
|
||||
infill_every_layers = 1
|
||||
infill_extruder = 1
|
||||
infill_extrusion_width = 0.44
|
||||
infill_first = 0
|
||||
infill_only_where_needed = 0
|
||||
infill_overlap = 30%
|
||||
infill_speed = 80
|
||||
inherits =
|
||||
interface_shells = 0
|
||||
layer_height = 0.2
|
||||
max_print_speed = 100
|
||||
max_volumetric_speed = 0
|
||||
min_skirt_length = 10
|
||||
notes =
|
||||
only_retract_when_crossing_perimeters = 0
|
||||
ooze_prevention = 0
|
||||
output_filename_format = [input_filename_base].gcode
|
||||
overhangs = 1
|
||||
perimeter_acceleration = 0
|
||||
perimeter_extruder = 1
|
||||
perimeter_extrusion_width = 0.44
|
||||
perimeter_speed = 60
|
||||
perimeters = 3
|
||||
post_process =
|
||||
print_settings_id =
|
||||
raft_layers = 0
|
||||
resolution = 0
|
||||
seam_position = aligned
|
||||
single_extruder_multi_material_priming = 1
|
||||
skirt_distance = 6
|
||||
skirt_height = 1
|
||||
skirts = 1
|
||||
slice_closing_radius = 0.049
|
||||
small_perimeter_speed = 50%
|
||||
solid_infill_below_area = 70
|
||||
solid_infill_every_layers = 0
|
||||
solid_infill_extruder = 1
|
||||
solid_infill_extrusion_width = 0.44
|
||||
solid_infill_speed = 50
|
||||
spiral_vase = 0
|
||||
standby_temperature_delta = -5
|
||||
support_material = 0
|
||||
support_material_angle = 0
|
||||
support_material_auto = 1
|
||||
support_material_buildplate_only = 1
|
||||
support_material_contact_distance = 0.2
|
||||
support_material_enforce_layers = 0
|
||||
support_material_extruder = 1
|
||||
support_material_extrusion_width = 0.45
|
||||
support_material_interface_contact_loops = 0
|
||||
support_material_interface_extruder = 1
|
||||
support_material_interface_layers = 3
|
||||
support_material_interface_spacing = 0
|
||||
support_material_interface_speed = 100%
|
||||
support_material_pattern = rectilinear
|
||||
support_material_spacing = 1.5
|
||||
support_material_speed = 50
|
||||
support_material_synchronize_layers = 0
|
||||
support_material_threshold = 20
|
||||
support_material_with_sheath = 1
|
||||
support_material_xy_spacing = 50%
|
||||
thin_walls = 1
|
||||
threads = 8
|
||||
top_fill_pattern = rectilinear
|
||||
top_infill_extrusion_width = 0.44
|
||||
top_solid_infill_speed = 20
|
||||
top_solid_layers = 3
|
||||
top_solid_min_thickness = 0
|
||||
travel_speed = 250
|
||||
wipe_tower = 0
|
||||
wipe_tower_bridging = 10
|
||||
wipe_tower_no_sparse_layers = 0
|
||||
wipe_tower_rotation_angle = 0
|
||||
wipe_tower_width = 60
|
||||
wipe_tower_x = 180
|
||||
wipe_tower_y = 140
|
||||
xy_size_compensation = 0
|
||||
@@ -0,0 +1,114 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-09 at 15:48:42 UTC
|
||||
avoid_crossing_perimeters = 0
|
||||
bottom_fill_pattern = rectilinear
|
||||
bottom_solid_layers = 3
|
||||
bottom_solid_min_thickness = 0
|
||||
bridge_acceleration = 0
|
||||
bridge_angle = 0
|
||||
bridge_flow_ratio = 0.91
|
||||
bridge_speed = 100
|
||||
brim_width = 0
|
||||
clip_multipart_objects = 1
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
complete_objects = 0
|
||||
default_acceleration = 0
|
||||
dont_support_bridges = 1
|
||||
draft_shield = 0
|
||||
elefant_foot_compensation = 0.1
|
||||
ensure_vertical_shell_thickness = 1
|
||||
external_perimeter_extrusion_width = 0.42
|
||||
external_perimeter_speed = 100
|
||||
external_perimeters_first = 0
|
||||
extra_perimeters = 1
|
||||
extruder_clearance_height = 20
|
||||
extruder_clearance_radius = 20
|
||||
extrusion_width = 0.44
|
||||
fill_angle = 45
|
||||
fill_density = 15%
|
||||
fill_pattern = cubic
|
||||
first_layer_acceleration = 0
|
||||
first_layer_extrusion_width = 0.44
|
||||
first_layer_height = 0.3
|
||||
first_layer_speed = 40
|
||||
gap_fill_speed = 100
|
||||
gcode_comments = 0
|
||||
gcode_label_objects = 0
|
||||
infill_acceleration = 0
|
||||
infill_every_layers = 1
|
||||
infill_extruder = 1
|
||||
infill_extrusion_width = 0.44
|
||||
infill_first = 0
|
||||
infill_only_where_needed = 0
|
||||
infill_overlap = 30%
|
||||
infill_speed = 100
|
||||
inherits =
|
||||
interface_shells = 0
|
||||
layer_height = 0.2
|
||||
max_print_speed = 200
|
||||
max_volumetric_speed = 0
|
||||
min_skirt_length = 10
|
||||
notes =
|
||||
only_retract_when_crossing_perimeters = 0
|
||||
ooze_prevention = 0
|
||||
output_filename_format = [input_filename_base].gcode
|
||||
overhangs = 1
|
||||
perimeter_acceleration = 0
|
||||
perimeter_extruder = 1
|
||||
perimeter_extrusion_width = 0.44
|
||||
perimeter_speed = 100
|
||||
perimeters = 3
|
||||
post_process =
|
||||
print_settings_id =
|
||||
raft_layers = 0
|
||||
resolution = 0
|
||||
seam_position = aligned
|
||||
single_extruder_multi_material_priming = 1
|
||||
skirt_distance = 6
|
||||
skirt_height = 1
|
||||
skirts = 1
|
||||
slice_closing_radius = 0.049
|
||||
small_perimeter_speed = 100
|
||||
solid_infill_below_area = 70
|
||||
solid_infill_every_layers = 0
|
||||
solid_infill_extruder = 1
|
||||
solid_infill_extrusion_width = 0.44
|
||||
solid_infill_speed = 100
|
||||
spiral_vase = 0
|
||||
standby_temperature_delta = -5
|
||||
support_material = 0
|
||||
support_material_angle = 0
|
||||
support_material_auto = 1
|
||||
support_material_buildplate_only = 1
|
||||
support_material_contact_distance = 0.2
|
||||
support_material_enforce_layers = 0
|
||||
support_material_extruder = 1
|
||||
support_material_extrusion_width = 0.45
|
||||
support_material_interface_contact_loops = 0
|
||||
support_material_interface_extruder = 1
|
||||
support_material_interface_layers = 3
|
||||
support_material_interface_spacing = 0
|
||||
support_material_interface_speed = 100%
|
||||
support_material_pattern = rectilinear
|
||||
support_material_spacing = 1.5
|
||||
support_material_speed = 100
|
||||
support_material_synchronize_layers = 0
|
||||
support_material_threshold = 20
|
||||
support_material_with_sheath = 1
|
||||
support_material_xy_spacing = 50%
|
||||
thin_walls = 1
|
||||
threads = 8
|
||||
top_fill_pattern = rectilinear
|
||||
top_infill_extrusion_width = 0.44
|
||||
top_solid_infill_speed = 100
|
||||
top_solid_layers = 3
|
||||
top_solid_min_thickness = 0
|
||||
travel_speed = 250
|
||||
wipe_tower = 0
|
||||
wipe_tower_bridging = 10
|
||||
wipe_tower_no_sparse_layers = 0
|
||||
wipe_tower_rotation_angle = 0
|
||||
wipe_tower_width = 60
|
||||
wipe_tower_x = 180
|
||||
wipe_tower_y = 140
|
||||
xy_size_compensation = 0
|
||||
@@ -0,0 +1,75 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-11 at 19:45:55 UTC
|
||||
bed_custom_model =
|
||||
bed_custom_texture =
|
||||
bed_shape = 89.6575x7.84402,88.6327x15.6283,86.9333x23.2937,84.5723x30.7818,81.5677x38.0356,77.9423x45,73.7237x51.6219,68.944x57.8509,63.6396x63.6396,57.8509x68.944,51.6219x73.7237,45x77.9423,38.0356x81.5677,30.7818x84.5723,23.2937x86.9333,15.6283x88.6327,7.84402x89.6575,5.51091e-15x90,-7.84402x89.6575,-15.6283x88.6327,-23.2937x86.9333,-30.7818x84.5723,-38.0356x81.5677,-45x77.9423,-51.6219x73.7237,-57.8509x68.944,-63.6396x63.6396,-68.944x57.8509,-73.7237x51.6219,-77.9423x45,-81.5677x38.0356,-84.5723x30.7818,-86.9333x23.2937,-88.6327x15.6283,-89.6575x7.84402,-90x1.10218e-14,-89.6575x-7.84402,-88.6327x-15.6283,-86.9333x-23.2937,-84.5723x-30.7818,-81.5677x-38.0356,-77.9423x-45,-73.7237x-51.6219,-68.944x-57.8509,-63.6396x-63.6396,-57.8509x-68.944,-51.6219x-73.7237,-45x-77.9423,-38.0356x-81.5677,-30.7818x-84.5723,-23.2937x-86.9333,-15.6283x-88.6327,-7.84402x-89.6575,-1.65327e-14x-90,7.84402x-89.6575,15.6283x-88.6327,23.2937x-86.9333,30.7818x-84.5723,38.0356x-81.5677,45x-77.9423,51.6219x-73.7237,57.8509x-68.944,63.6396x-63.6396,68.944x-57.8509,73.7237x-51.6219,77.9423x-45,81.5677x-38.0356,84.5723x-30.7818,86.9333x-23.2937,88.6327x-15.6283,89.6575x-7.84402,90x-2.20436e-14
|
||||
before_layer_gcode = ; Layer change to Layer [layer_num]\n; Z=[layer_z]\n
|
||||
between_objects_gcode =
|
||||
cooling_tube_length = 5
|
||||
cooling_tube_retraction = 91.5
|
||||
default_filament_profile = ""
|
||||
default_print_profile =
|
||||
deretract_speed = 0
|
||||
end_gcode = M104 S0 ; turn off hotend temperature\nM190 S0; turn off bed temperature\nG28 ; home \nM84 ; disable motors\n\n
|
||||
extra_loading_move = -2
|
||||
extruder_colour = #019B9B
|
||||
extruder_offset = 0x0
|
||||
gcode_flavor = marlin
|
||||
high_current_on_filament_swap = 0
|
||||
host_type = octoprint
|
||||
inherits =
|
||||
layer_gcode =
|
||||
machine_max_acceleration_e = 10000,5000
|
||||
machine_max_acceleration_extruding = 1500,1250
|
||||
machine_max_acceleration_retracting = 1500,1250
|
||||
machine_max_acceleration_x = 9000,9000
|
||||
machine_max_acceleration_y = 9000,9000
|
||||
machine_max_acceleration_z = 9000,9000
|
||||
machine_max_feedrate_e = 250,250
|
||||
machine_max_feedrate_x = 1500,1500
|
||||
machine_max_feedrate_y = 1500,1500
|
||||
machine_max_feedrate_z = 1500,1500
|
||||
machine_max_jerk_e = 2.5,2.5
|
||||
machine_max_jerk_x = 9,9
|
||||
machine_max_jerk_y = 9,9
|
||||
machine_max_jerk_z = 9,9
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
max_layer_height = 0
|
||||
max_print_height = 196
|
||||
min_layer_height = 0.1
|
||||
nozzle_diameter = 0.4
|
||||
parking_pos_retraction = 92
|
||||
print_host =
|
||||
printer_model =
|
||||
printer_notes =
|
||||
printer_settings_id =
|
||||
printer_technology = FFF
|
||||
printer_variant =
|
||||
printer_vendor =
|
||||
printhost_apikey =
|
||||
printhost_cafile =
|
||||
remaining_times = 1
|
||||
retract_before_travel = 2
|
||||
retract_before_wipe = 10%
|
||||
retract_layer_change = 0
|
||||
retract_length = 1.85
|
||||
retract_length_toolchange = 10
|
||||
retract_lift = 0.2
|
||||
retract_lift_above = 0.4
|
||||
retract_lift_below = 150
|
||||
retract_restart_extra = 0
|
||||
retract_restart_extra_toolchange = 0
|
||||
retract_speed = 30
|
||||
serial_port =
|
||||
serial_speed = 250000
|
||||
silent_mode = 1
|
||||
single_extruder_multi_material = 0
|
||||
start_gcode = G28 ; home all axes\nM140 S[first_layer_bed_temperature] ; set bed final temp\nG1 X0 Y0 Z100 F4000 ; safe position\nG1 X-65 Y42 Z5 F4000 ; lift nozzle\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\nM104 S[first_layer_temperature] ; set extruder final temp\nM109 S[first_layer_temperature] ; wait for extruder final temp\nG1 X-67 Y40 Z0.3 F3000 ; move down\nG1 Z0.5; lift\nG92 E0\n{if perimeter_speed >= 100}M900 K0; Disable LINEAR_ADVANCE for speed's sake!\n{elsif perimeter_speed >= 65}M900 K0.2; reduced LINEAR_ADVANCE because of higher speeds\n{else}M900 K0.38; LINEAR_ADVANCE high quality preset\n{endif}
|
||||
thumbnails =
|
||||
toolchange_gcode =
|
||||
use_firmware_retraction = 0
|
||||
use_relative_e_distances = 0
|
||||
use_volumetric_e = 0
|
||||
variable_layer_height = 1
|
||||
wipe = 0
|
||||
z_offset = 0
|
||||
@@ -0,0 +1,19 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-30 at 21:39:05 UTC
|
||||
|
||||
[snapshot]
|
||||
id = 20201030T213905Z
|
||||
time_captured = 20201030T213905Z
|
||||
slic3r_version_captured = 2.2.0+linux-x64
|
||||
comment =
|
||||
reason = upgrade
|
||||
|
||||
[presets]
|
||||
print = delta
|
||||
filament = PLA_Noulei-Silk Filaments
|
||||
printer = delta
|
||||
|
||||
[Vendor:PrusaResearch]
|
||||
version = 1.1.9
|
||||
min_slic3r_version = 2.2.0-alpha3
|
||||
max_slic3r_version = 2147483647.2147483647.2147483647
|
||||
model_MINI = 0.25;0.4;0.6
|
||||
+5289
File diff suppressed because it is too large
Load Diff
@@ -0,0 +1,55 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-11-09 at 06:05:44 UTC
|
||||
bed_temperature = 70
|
||||
bridge_fan_speed = 100
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
compatible_prints =
|
||||
compatible_prints_condition =
|
||||
cooling = 1
|
||||
disable_fan_first_layers = 1
|
||||
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
||||
extrusion_multiplier = 0.97
|
||||
fan_always_on = 1
|
||||
fan_below_layer_time = 60
|
||||
filament_colour = #000000
|
||||
filament_cooling_final_speed = 3.4
|
||||
filament_cooling_initial_speed = 2.2
|
||||
filament_cooling_moves = 4
|
||||
filament_cost = 20
|
||||
filament_density = 1.18
|
||||
filament_deretract_speed = nil
|
||||
filament_diameter = 1.75
|
||||
filament_load_time = 0
|
||||
filament_loading_speed = 28
|
||||
filament_loading_speed_start = 3
|
||||
filament_max_volumetric_speed = 0
|
||||
filament_minimal_purge_on_wipe_tower = 15
|
||||
filament_notes = "Noulei Silk PLA Filaments.\nPrint well on low temps <200°C, but black has far better strength and layer adhesion than the bright colours.\nSuccessfully tested filaments already testet on delta /w e3dv6/0.4:\n\n#24 Silk Black\n#11Silk Blue\n#14Silk Silver Blue\n\nnext ones to test out:\n#26 antique gold\n#9 red\n#4 white\npetg?"
|
||||
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
||||
filament_retract_before_travel = nil
|
||||
filament_retract_before_wipe = nil
|
||||
filament_retract_layer_change = nil
|
||||
filament_retract_length = nil
|
||||
filament_retract_lift = nil
|
||||
filament_retract_lift_above = nil
|
||||
filament_retract_lift_below = nil
|
||||
filament_retract_restart_extra = nil
|
||||
filament_retract_speed = nil
|
||||
filament_settings_id = ""
|
||||
filament_soluble = 0
|
||||
filament_toolchange_delay = 0
|
||||
filament_type = PET
|
||||
filament_unload_time = 0
|
||||
filament_unloading_speed = 90
|
||||
filament_unloading_speed_start = 100
|
||||
filament_vendor = (Unknown)
|
||||
filament_wipe = nil
|
||||
first_layer_bed_temperature = 72
|
||||
first_layer_temperature = 235
|
||||
inherits =
|
||||
max_fan_speed = 100
|
||||
min_fan_speed = 100
|
||||
min_print_speed = 10
|
||||
slowdown_below_layer_time = 8
|
||||
start_filament_gcode = "; Filament gcode\n"
|
||||
temperature = 230
|
||||
@@ -0,0 +1,55 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-15 at 21:23:23 UTC
|
||||
bed_temperature = 55
|
||||
bridge_fan_speed = 100
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
compatible_prints =
|
||||
compatible_prints_condition =
|
||||
cooling = 1
|
||||
disable_fan_first_layers = 1
|
||||
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
||||
extrusion_multiplier = 0.95
|
||||
fan_always_on = 1
|
||||
fan_below_layer_time = 60
|
||||
filament_colour = #000000
|
||||
filament_cooling_final_speed = 3.4
|
||||
filament_cooling_initial_speed = 2.2
|
||||
filament_cooling_moves = 4
|
||||
filament_cost = 20
|
||||
filament_density = 1.18
|
||||
filament_deretract_speed = nil
|
||||
filament_diameter = 1.75
|
||||
filament_load_time = 0
|
||||
filament_loading_speed = 28
|
||||
filament_loading_speed_start = 3
|
||||
filament_max_volumetric_speed = 0
|
||||
filament_minimal_purge_on_wipe_tower = 15
|
||||
filament_notes = "Noulei Silk PLA Filaments.\nPrint well on low temps <200°C, but black has far better strength and layer adhesion than the bright colours.\nSuccessfully tested filaments already testet on delta /w e3dv6/0.4:\n\n#24 Silk Black\n#11Silk Blue\n#14Silk Silver Blue\n\nnext ones to test out:\n#26 antique gold\n#9 red\n#4 white\npetg?"
|
||||
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
||||
filament_retract_before_travel = nil
|
||||
filament_retract_before_wipe = nil
|
||||
filament_retract_layer_change = nil
|
||||
filament_retract_length = nil
|
||||
filament_retract_lift = nil
|
||||
filament_retract_lift_above = nil
|
||||
filament_retract_lift_below = nil
|
||||
filament_retract_restart_extra = nil
|
||||
filament_retract_speed = nil
|
||||
filament_settings_id = ""
|
||||
filament_soluble = 0
|
||||
filament_toolchange_delay = 0
|
||||
filament_type = PLA
|
||||
filament_unload_time = 0
|
||||
filament_unloading_speed = 90
|
||||
filament_unloading_speed_start = 100
|
||||
filament_vendor = (Unknown)
|
||||
filament_wipe = nil
|
||||
first_layer_bed_temperature = 55
|
||||
first_layer_temperature = 192
|
||||
inherits =
|
||||
max_fan_speed = 100
|
||||
min_fan_speed = 40
|
||||
min_print_speed = 10
|
||||
slowdown_below_layer_time = 8
|
||||
start_filament_gcode = "; Filament gcode\n"
|
||||
temperature = 190
|
||||
@@ -0,0 +1,114 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-11-17 at 13:29:52 UTC
|
||||
avoid_crossing_perimeters = 0
|
||||
bottom_fill_pattern = rectilinear
|
||||
bottom_solid_layers = 4
|
||||
bottom_solid_min_thickness = 0
|
||||
bridge_acceleration = 0
|
||||
bridge_angle = 0
|
||||
bridge_flow_ratio = 0.91
|
||||
bridge_speed = 60
|
||||
brim_width = 0
|
||||
clip_multipart_objects = 1
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
complete_objects = 0
|
||||
default_acceleration = 0
|
||||
dont_support_bridges = 1
|
||||
draft_shield = 0
|
||||
elefant_foot_compensation = 0.1
|
||||
ensure_vertical_shell_thickness = 1
|
||||
external_perimeter_extrusion_width = 0.42
|
||||
external_perimeter_speed = 30
|
||||
external_perimeters_first = 0
|
||||
extra_perimeters = 1
|
||||
extruder_clearance_height = 20
|
||||
extruder_clearance_radius = 20
|
||||
extrusion_width = 0.44
|
||||
fill_angle = 45
|
||||
fill_density = 50%
|
||||
fill_pattern = cubic
|
||||
first_layer_acceleration = 0
|
||||
first_layer_extrusion_width = 0.44
|
||||
first_layer_height = 0.3
|
||||
first_layer_speed = 15
|
||||
gap_fill_speed = 20
|
||||
gcode_comments = 0
|
||||
gcode_label_objects = 0
|
||||
infill_acceleration = 0
|
||||
infill_every_layers = 1
|
||||
infill_extruder = 1
|
||||
infill_extrusion_width = 0.44
|
||||
infill_first = 0
|
||||
infill_only_where_needed = 0
|
||||
infill_overlap = 25%
|
||||
infill_speed = 80
|
||||
inherits =
|
||||
interface_shells = 0
|
||||
layer_height = 0.3
|
||||
max_print_speed = 100
|
||||
max_volumetric_speed = 0
|
||||
min_skirt_length = 15
|
||||
notes =
|
||||
only_retract_when_crossing_perimeters = 0
|
||||
ooze_prevention = 0
|
||||
output_filename_format = [input_filename_base].gcode
|
||||
overhangs = 1
|
||||
perimeter_acceleration = 0
|
||||
perimeter_extruder = 1
|
||||
perimeter_extrusion_width = 0.44
|
||||
perimeter_speed = 60
|
||||
perimeters = 4
|
||||
post_process =
|
||||
print_settings_id =
|
||||
raft_layers = 0
|
||||
resolution = 0
|
||||
seam_position = aligned
|
||||
single_extruder_multi_material_priming = 1
|
||||
skirt_distance = 4
|
||||
skirt_height = 1
|
||||
skirts = 1
|
||||
slice_closing_radius = 0.049
|
||||
small_perimeter_speed = 50%
|
||||
solid_infill_below_area = 70
|
||||
solid_infill_every_layers = 0
|
||||
solid_infill_extruder = 1
|
||||
solid_infill_extrusion_width = 0.44
|
||||
solid_infill_speed = 60
|
||||
spiral_vase = 0
|
||||
standby_temperature_delta = -5
|
||||
support_material = 0
|
||||
support_material_angle = 0
|
||||
support_material_auto = 1
|
||||
support_material_buildplate_only = 1
|
||||
support_material_contact_distance = 0.23
|
||||
support_material_enforce_layers = 0
|
||||
support_material_extruder = 1
|
||||
support_material_extrusion_width = 0.45
|
||||
support_material_interface_contact_loops = 0
|
||||
support_material_interface_extruder = 1
|
||||
support_material_interface_layers = 3
|
||||
support_material_interface_spacing = 0
|
||||
support_material_interface_speed = 100%
|
||||
support_material_pattern = rectilinear-grid
|
||||
support_material_spacing = 2.5
|
||||
support_material_speed = 60
|
||||
support_material_synchronize_layers = 0
|
||||
support_material_threshold = 25
|
||||
support_material_with_sheath = 1
|
||||
support_material_xy_spacing = 60%
|
||||
thin_walls = 1
|
||||
threads = 8
|
||||
top_fill_pattern = rectilinear
|
||||
top_infill_extrusion_width = 0.44
|
||||
top_solid_infill_speed = 20
|
||||
top_solid_layers = 4
|
||||
top_solid_min_thickness = 0
|
||||
travel_speed = 222
|
||||
wipe_tower = 0
|
||||
wipe_tower_bridging = 10
|
||||
wipe_tower_no_sparse_layers = 0
|
||||
wipe_tower_rotation_angle = 0
|
||||
wipe_tower_width = 60
|
||||
wipe_tower_x = 180
|
||||
wipe_tower_y = 140
|
||||
xy_size_compensation = 0
|
||||
@@ -0,0 +1,114 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-09 at 15:48:42 UTC
|
||||
avoid_crossing_perimeters = 0
|
||||
bottom_fill_pattern = rectilinear
|
||||
bottom_solid_layers = 3
|
||||
bottom_solid_min_thickness = 0
|
||||
bridge_acceleration = 0
|
||||
bridge_angle = 0
|
||||
bridge_flow_ratio = 0.91
|
||||
bridge_speed = 100
|
||||
brim_width = 0
|
||||
clip_multipart_objects = 1
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
complete_objects = 0
|
||||
default_acceleration = 0
|
||||
dont_support_bridges = 1
|
||||
draft_shield = 0
|
||||
elefant_foot_compensation = 0.1
|
||||
ensure_vertical_shell_thickness = 1
|
||||
external_perimeter_extrusion_width = 0.42
|
||||
external_perimeter_speed = 100
|
||||
external_perimeters_first = 0
|
||||
extra_perimeters = 1
|
||||
extruder_clearance_height = 20
|
||||
extruder_clearance_radius = 20
|
||||
extrusion_width = 0.44
|
||||
fill_angle = 45
|
||||
fill_density = 15%
|
||||
fill_pattern = cubic
|
||||
first_layer_acceleration = 0
|
||||
first_layer_extrusion_width = 0.44
|
||||
first_layer_height = 0.3
|
||||
first_layer_speed = 40
|
||||
gap_fill_speed = 100
|
||||
gcode_comments = 0
|
||||
gcode_label_objects = 0
|
||||
infill_acceleration = 0
|
||||
infill_every_layers = 1
|
||||
infill_extruder = 1
|
||||
infill_extrusion_width = 0.44
|
||||
infill_first = 0
|
||||
infill_only_where_needed = 0
|
||||
infill_overlap = 30%
|
||||
infill_speed = 100
|
||||
inherits =
|
||||
interface_shells = 0
|
||||
layer_height = 0.2
|
||||
max_print_speed = 200
|
||||
max_volumetric_speed = 0
|
||||
min_skirt_length = 10
|
||||
notes =
|
||||
only_retract_when_crossing_perimeters = 0
|
||||
ooze_prevention = 0
|
||||
output_filename_format = [input_filename_base].gcode
|
||||
overhangs = 1
|
||||
perimeter_acceleration = 0
|
||||
perimeter_extruder = 1
|
||||
perimeter_extrusion_width = 0.44
|
||||
perimeter_speed = 100
|
||||
perimeters = 3
|
||||
post_process =
|
||||
print_settings_id =
|
||||
raft_layers = 0
|
||||
resolution = 0
|
||||
seam_position = aligned
|
||||
single_extruder_multi_material_priming = 1
|
||||
skirt_distance = 6
|
||||
skirt_height = 1
|
||||
skirts = 1
|
||||
slice_closing_radius = 0.049
|
||||
small_perimeter_speed = 100
|
||||
solid_infill_below_area = 70
|
||||
solid_infill_every_layers = 0
|
||||
solid_infill_extruder = 1
|
||||
solid_infill_extrusion_width = 0.44
|
||||
solid_infill_speed = 100
|
||||
spiral_vase = 0
|
||||
standby_temperature_delta = -5
|
||||
support_material = 0
|
||||
support_material_angle = 0
|
||||
support_material_auto = 1
|
||||
support_material_buildplate_only = 1
|
||||
support_material_contact_distance = 0.2
|
||||
support_material_enforce_layers = 0
|
||||
support_material_extruder = 1
|
||||
support_material_extrusion_width = 0.45
|
||||
support_material_interface_contact_loops = 0
|
||||
support_material_interface_extruder = 1
|
||||
support_material_interface_layers = 3
|
||||
support_material_interface_spacing = 0
|
||||
support_material_interface_speed = 100%
|
||||
support_material_pattern = rectilinear
|
||||
support_material_spacing = 1.5
|
||||
support_material_speed = 100
|
||||
support_material_synchronize_layers = 0
|
||||
support_material_threshold = 20
|
||||
support_material_with_sheath = 1
|
||||
support_material_xy_spacing = 50%
|
||||
thin_walls = 1
|
||||
threads = 8
|
||||
top_fill_pattern = rectilinear
|
||||
top_infill_extrusion_width = 0.44
|
||||
top_solid_infill_speed = 100
|
||||
top_solid_layers = 3
|
||||
top_solid_min_thickness = 0
|
||||
travel_speed = 250
|
||||
wipe_tower = 0
|
||||
wipe_tower_bridging = 10
|
||||
wipe_tower_no_sparse_layers = 0
|
||||
wipe_tower_rotation_angle = 0
|
||||
wipe_tower_width = 60
|
||||
wipe_tower_x = 180
|
||||
wipe_tower_y = 140
|
||||
xy_size_compensation = 0
|
||||
@@ -0,0 +1,75 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-11-07 at 20:30:02 UTC
|
||||
bed_custom_model =
|
||||
bed_custom_texture =
|
||||
bed_shape = 89.6575x7.84402,88.6327x15.6283,86.9333x23.2937,84.5723x30.7818,81.5677x38.0356,77.9423x45,73.7237x51.6219,68.944x57.8509,63.6396x63.6396,57.8509x68.944,51.6219x73.7237,45x77.9423,38.0356x81.5677,30.7818x84.5723,23.2937x86.9333,15.6283x88.6327,7.84402x89.6575,5.51091e-15x90,-7.84402x89.6575,-15.6283x88.6327,-23.2937x86.9333,-30.7818x84.5723,-38.0356x81.5677,-45x77.9423,-51.6219x73.7237,-57.8509x68.944,-63.6396x63.6396,-68.944x57.8509,-73.7237x51.6219,-77.9423x45,-81.5677x38.0356,-84.5723x30.7818,-86.9333x23.2937,-88.6327x15.6283,-89.6575x7.84402,-90x1.10218e-14,-89.6575x-7.84402,-88.6327x-15.6283,-86.9333x-23.2937,-84.5723x-30.7818,-81.5677x-38.0356,-77.9423x-45,-73.7237x-51.6219,-68.944x-57.8509,-63.6396x-63.6396,-57.8509x-68.944,-51.6219x-73.7237,-45x-77.9423,-38.0356x-81.5677,-30.7818x-84.5723,-23.2937x-86.9333,-15.6283x-88.6327,-7.84402x-89.6575,-1.65327e-14x-90,7.84402x-89.6575,15.6283x-88.6327,23.2937x-86.9333,30.7818x-84.5723,38.0356x-81.5677,45x-77.9423,51.6219x-73.7237,57.8509x-68.944,63.6396x-63.6396,68.944x-57.8509,73.7237x-51.6219,77.9423x-45,81.5677x-38.0356,84.5723x-30.7818,86.9333x-23.2937,88.6327x-15.6283,89.6575x-7.84402,90x-2.20436e-14
|
||||
before_layer_gcode = ; Layer change to Layer [layer_num]\n; Z=[layer_z]\n
|
||||
between_objects_gcode =
|
||||
cooling_tube_length = 5
|
||||
cooling_tube_retraction = 91.5
|
||||
default_filament_profile = ""
|
||||
default_print_profile =
|
||||
deretract_speed = 0
|
||||
end_gcode = M104 S0 ; turn off hotend temperature\nM190 S0; turn off bed temperature\nM106; hotend fan full blast\nG28; home \nM84; disable motors\nG4 S10; wait 10 seconds for hotend cooldown\n; play some tunes:\n;Mission Impossible\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2637 P75\nM300 S2793 P75\nM300 S2959 P75\nM300 S3135 P75\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S1864 P150\nM300 S0 P150\nM300 S2093 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S2793 P150\nM300 S0 P150\nM300 S2959 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S1864 P150\nM300 S0 P150\nM300 S2093 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S2793 P150\nM300 S0 P150\nM300 S2959 P150\nM300 S0 P150\nM300 S1864 P150\nM300 S3135 P150\nM300 S2349 P1200\nM300 S0 P75\nM300 S1864 P150\nM300 S3135 P150\nM300 S2217 P1200\nM300 S0 P75\nM300 S1864 P150\nM300 S3135 P150\nM300 S2093 P1200\nM300 S0 P150\nM300 S932 P150\nM300 S2093 P150\n; end of tune\nG4 S120; wait another 2 Minutes for hotend cooldown\nM107; hotend fan off
|
||||
extra_loading_move = -2
|
||||
extruder_colour = #019B9B
|
||||
extruder_offset = 0x0
|
||||
gcode_flavor = marlin
|
||||
high_current_on_filament_swap = 0
|
||||
host_type = octoprint
|
||||
inherits =
|
||||
layer_gcode =
|
||||
machine_max_acceleration_e = 10000,5000
|
||||
machine_max_acceleration_extruding = 1500,1250
|
||||
machine_max_acceleration_retracting = 1500,1250
|
||||
machine_max_acceleration_x = 9000,9000
|
||||
machine_max_acceleration_y = 9000,9000
|
||||
machine_max_acceleration_z = 9000,9000
|
||||
machine_max_feedrate_e = 250,250
|
||||
machine_max_feedrate_x = 1500,1500
|
||||
machine_max_feedrate_y = 1500,1500
|
||||
machine_max_feedrate_z = 1500,1500
|
||||
machine_max_jerk_e = 2.5,2.5
|
||||
machine_max_jerk_x = 9,9
|
||||
machine_max_jerk_y = 9,9
|
||||
machine_max_jerk_z = 9,9
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
max_layer_height = 0
|
||||
max_print_height = 196
|
||||
min_layer_height = 0.1
|
||||
nozzle_diameter = 0.4
|
||||
parking_pos_retraction = 92
|
||||
print_host =
|
||||
printer_model =
|
||||
printer_notes =
|
||||
printer_settings_id =
|
||||
printer_technology = FFF
|
||||
printer_variant =
|
||||
printer_vendor =
|
||||
printhost_apikey =
|
||||
printhost_cafile =
|
||||
remaining_times = 1
|
||||
retract_before_travel = 2
|
||||
retract_before_wipe = 10%
|
||||
retract_layer_change = 0
|
||||
retract_length = 2
|
||||
retract_length_toolchange = 10
|
||||
retract_lift = 0.2
|
||||
retract_lift_above = 0.3
|
||||
retract_lift_below = 150
|
||||
retract_restart_extra = 0
|
||||
retract_restart_extra_toolchange = 0
|
||||
retract_speed = 30
|
||||
serial_port =
|
||||
serial_speed = 250000
|
||||
silent_mode = 1
|
||||
single_extruder_multi_material = 0
|
||||
start_gcode = G28 ; home all axes\nM140 S[first_layer_bed_temperature] ; set bed final temp\nG1 X0 Y0 Z100 F4000 ; safe position\nG1 X0 Y-50 Z5 F4000 ; lift nozzle\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\nM104 S[first_layer_temperature] ; set extruder final temp\nM109 S[first_layer_temperature] ; wait for extruder final temp\nG1 X0 Y-45 Z0.3 F3000 ; move down\n;G1 Z0.5; lift\nG92 E0\n{if perimeter_speed >= 100}M900 K0; Disable LINEAR_ADVANCE for speed's sake!\n{elsif perimeter_speed >= 65}M900 K0.2; reduced LINEAR_ADVANCE because of higher speeds\n{else}M900 K0.38; LINEAR_ADVANCE high quality preset\n{endif}
|
||||
thumbnails =
|
||||
toolchange_gcode =
|
||||
use_firmware_retraction = 0
|
||||
use_relative_e_distances = 0
|
||||
use_volumetric_e = 0
|
||||
variable_layer_height = 1
|
||||
wipe = 0
|
||||
z_offset = 0
|
||||
@@ -0,0 +1,19 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-12-23 at 21:26:23 UTC
|
||||
|
||||
[snapshot]
|
||||
id = 20201223T212623Z
|
||||
time_captured = 20201223T212623Z
|
||||
slic3r_version_captured = 2.2.0+linux-x64
|
||||
comment =
|
||||
reason = upgrade
|
||||
|
||||
[presets]
|
||||
print = delta
|
||||
filament = PLA_Noulei-Silk Filaments
|
||||
printer = delta
|
||||
|
||||
[Vendor:PrusaResearch]
|
||||
version = 1.1.10
|
||||
min_slic3r_version = 2.2.0-alpha3
|
||||
max_slic3r_version = 2147483647.2147483647.2147483647
|
||||
model_MINI = 0.25;0.4;0.6
|
||||
+5289
File diff suppressed because it is too large
Load Diff
@@ -0,0 +1,57 @@
|
||||
# generated by PrusaSlicer 2.3.0+linux-x64 on 2021-02-18 at 11:28:23 UTC
|
||||
bed_temperature = 70
|
||||
bridge_fan_speed = 100
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
compatible_prints =
|
||||
compatible_prints_condition =
|
||||
cooling = 1
|
||||
disable_fan_first_layers = 1
|
||||
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
||||
extrusion_multiplier = 0.97
|
||||
fan_always_on = 1
|
||||
fan_below_layer_time = 30
|
||||
filament_colour = #000000
|
||||
filament_cooling_final_speed = 3.4
|
||||
filament_cooling_initial_speed = 2.2
|
||||
filament_cooling_moves = 4
|
||||
filament_cost = 20
|
||||
filament_density = 1.18
|
||||
filament_deretract_speed = nil
|
||||
filament_diameter = 1.75
|
||||
filament_load_time = 0
|
||||
filament_loading_speed = 28
|
||||
filament_loading_speed_start = 3
|
||||
filament_max_volumetric_speed = 0
|
||||
filament_minimal_purge_on_wipe_tower = 15
|
||||
filament_notes = "Noulei Silk PLA Filaments.\nPrint well on low temps <200°C, but black has far better strength and layer adhesion than the bright colours.\nSuccessfully tested filaments already testet on delta /w e3dv6/0.4:\n#24 Silk Black\n#11Silk Blue\n#14Silk Silver Blue\n\nDasFilament PETG:\nusually good at 230/70°C, but spahipblau prints better at 220.\n\nnext ones to test out:\n#26 antique gold\n#9 red\n#4 white\npetg?"
|
||||
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
||||
filament_retract_before_travel = nil
|
||||
filament_retract_before_wipe = nil
|
||||
filament_retract_layer_change = nil
|
||||
filament_retract_length = nil
|
||||
filament_retract_lift = nil
|
||||
filament_retract_lift_above = nil
|
||||
filament_retract_lift_below = nil
|
||||
filament_retract_restart_extra = nil
|
||||
filament_retract_speed = nil
|
||||
filament_settings_id = PETG-DasFilament_Saphirblau
|
||||
filament_soluble = 0
|
||||
filament_spool_weight = 0
|
||||
filament_toolchange_delay = 0
|
||||
filament_type = PET
|
||||
filament_unload_time = 0
|
||||
filament_unloading_speed = 90
|
||||
filament_unloading_speed_start = 100
|
||||
filament_vendor = (Unknown)
|
||||
filament_wipe = nil
|
||||
first_layer_bed_temperature = 72
|
||||
first_layer_temperature = 225
|
||||
full_fan_speed_layer = 0
|
||||
inherits =
|
||||
max_fan_speed = 85
|
||||
min_fan_speed = 35
|
||||
min_print_speed = 10
|
||||
slowdown_below_layer_time = 8
|
||||
start_filament_gcode = "; Filament gcode\n"
|
||||
temperature = 220
|
||||
@@ -0,0 +1,55 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-11-09 at 06:05:44 UTC
|
||||
bed_temperature = 70
|
||||
bridge_fan_speed = 100
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
compatible_prints =
|
||||
compatible_prints_condition =
|
||||
cooling = 1
|
||||
disable_fan_first_layers = 1
|
||||
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
||||
extrusion_multiplier = 0.97
|
||||
fan_always_on = 1
|
||||
fan_below_layer_time = 60
|
||||
filament_colour = #000000
|
||||
filament_cooling_final_speed = 3.4
|
||||
filament_cooling_initial_speed = 2.2
|
||||
filament_cooling_moves = 4
|
||||
filament_cost = 20
|
||||
filament_density = 1.18
|
||||
filament_deretract_speed = nil
|
||||
filament_diameter = 1.75
|
||||
filament_load_time = 0
|
||||
filament_loading_speed = 28
|
||||
filament_loading_speed_start = 3
|
||||
filament_max_volumetric_speed = 0
|
||||
filament_minimal_purge_on_wipe_tower = 15
|
||||
filament_notes = "Noulei Silk PLA Filaments.\nPrint well on low temps <200°C, but black has far better strength and layer adhesion than the bright colours.\nSuccessfully tested filaments already testet on delta /w e3dv6/0.4:\n\n#24 Silk Black\n#11Silk Blue\n#14Silk Silver Blue\n\nnext ones to test out:\n#26 antique gold\n#9 red\n#4 white\npetg?"
|
||||
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
||||
filament_retract_before_travel = nil
|
||||
filament_retract_before_wipe = nil
|
||||
filament_retract_layer_change = nil
|
||||
filament_retract_length = nil
|
||||
filament_retract_lift = nil
|
||||
filament_retract_lift_above = nil
|
||||
filament_retract_lift_below = nil
|
||||
filament_retract_restart_extra = nil
|
||||
filament_retract_speed = nil
|
||||
filament_settings_id = ""
|
||||
filament_soluble = 0
|
||||
filament_toolchange_delay = 0
|
||||
filament_type = PET
|
||||
filament_unload_time = 0
|
||||
filament_unloading_speed = 90
|
||||
filament_unloading_speed_start = 100
|
||||
filament_vendor = (Unknown)
|
||||
filament_wipe = nil
|
||||
first_layer_bed_temperature = 72
|
||||
first_layer_temperature = 235
|
||||
inherits =
|
||||
max_fan_speed = 100
|
||||
min_fan_speed = 100
|
||||
min_print_speed = 10
|
||||
slowdown_below_layer_time = 8
|
||||
start_filament_gcode = "; Filament gcode\n"
|
||||
temperature = 230
|
||||
@@ -0,0 +1,55 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-15 at 21:23:23 UTC
|
||||
bed_temperature = 55
|
||||
bridge_fan_speed = 100
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
compatible_prints =
|
||||
compatible_prints_condition =
|
||||
cooling = 1
|
||||
disable_fan_first_layers = 1
|
||||
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
||||
extrusion_multiplier = 0.95
|
||||
fan_always_on = 1
|
||||
fan_below_layer_time = 60
|
||||
filament_colour = #000000
|
||||
filament_cooling_final_speed = 3.4
|
||||
filament_cooling_initial_speed = 2.2
|
||||
filament_cooling_moves = 4
|
||||
filament_cost = 20
|
||||
filament_density = 1.18
|
||||
filament_deretract_speed = nil
|
||||
filament_diameter = 1.75
|
||||
filament_load_time = 0
|
||||
filament_loading_speed = 28
|
||||
filament_loading_speed_start = 3
|
||||
filament_max_volumetric_speed = 0
|
||||
filament_minimal_purge_on_wipe_tower = 15
|
||||
filament_notes = "Noulei Silk PLA Filaments.\nPrint well on low temps <200°C, but black has far better strength and layer adhesion than the bright colours.\nSuccessfully tested filaments already testet on delta /w e3dv6/0.4:\n\n#24 Silk Black\n#11Silk Blue\n#14Silk Silver Blue\n\nnext ones to test out:\n#26 antique gold\n#9 red\n#4 white\npetg?"
|
||||
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
||||
filament_retract_before_travel = nil
|
||||
filament_retract_before_wipe = nil
|
||||
filament_retract_layer_change = nil
|
||||
filament_retract_length = nil
|
||||
filament_retract_lift = nil
|
||||
filament_retract_lift_above = nil
|
||||
filament_retract_lift_below = nil
|
||||
filament_retract_restart_extra = nil
|
||||
filament_retract_speed = nil
|
||||
filament_settings_id = ""
|
||||
filament_soluble = 0
|
||||
filament_toolchange_delay = 0
|
||||
filament_type = PLA
|
||||
filament_unload_time = 0
|
||||
filament_unloading_speed = 90
|
||||
filament_unloading_speed_start = 100
|
||||
filament_vendor = (Unknown)
|
||||
filament_wipe = nil
|
||||
first_layer_bed_temperature = 55
|
||||
first_layer_temperature = 192
|
||||
inherits =
|
||||
max_fan_speed = 100
|
||||
min_fan_speed = 40
|
||||
min_print_speed = 10
|
||||
slowdown_below_layer_time = 8
|
||||
start_filament_gcode = "; Filament gcode\n"
|
||||
temperature = 190
|
||||
@@ -0,0 +1,122 @@
|
||||
# generated by PrusaSlicer 2.3.0+linux-x64 on 2021-02-18 at 22:33:05 UTC
|
||||
avoid_crossing_perimeters = 0
|
||||
avoid_crossing_perimeters_max_detour = 0
|
||||
bottom_fill_pattern = monotonic
|
||||
bottom_solid_layers = 4
|
||||
bottom_solid_min_thickness = 0
|
||||
bridge_acceleration = 0
|
||||
bridge_angle = 0
|
||||
bridge_flow_ratio = 0.91
|
||||
bridge_speed = 60
|
||||
brim_width = 0
|
||||
clip_multipart_objects = 1
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
complete_objects = 0
|
||||
default_acceleration = 0
|
||||
dont_support_bridges = 1
|
||||
draft_shield = 0
|
||||
elefant_foot_compensation = 0.1
|
||||
ensure_vertical_shell_thickness = 1
|
||||
external_perimeter_extrusion_width = 0.42
|
||||
external_perimeter_speed = 20
|
||||
external_perimeters_first = 0
|
||||
extra_perimeters = 1
|
||||
extruder_clearance_height = 20
|
||||
extruder_clearance_radius = 20
|
||||
extrusion_width = 0.44
|
||||
fill_angle = 45
|
||||
fill_density = 20%
|
||||
fill_pattern = cubic
|
||||
first_layer_acceleration = 0
|
||||
first_layer_extrusion_width = 0.44
|
||||
first_layer_height = 0.2
|
||||
first_layer_speed = 15
|
||||
gap_fill_speed = 20
|
||||
gcode_comments = 0
|
||||
gcode_label_objects = 0
|
||||
infill_acceleration = 0
|
||||
infill_anchor = 600%
|
||||
infill_anchor_max = 50
|
||||
infill_every_layers = 1
|
||||
infill_extruder = 1
|
||||
infill_extrusion_width = 0.44
|
||||
infill_first = 0
|
||||
infill_only_where_needed = 0
|
||||
infill_overlap = 25%
|
||||
infill_speed = 80
|
||||
inherits =
|
||||
interface_shells = 0
|
||||
ironing = 0
|
||||
ironing_flowrate = 12%
|
||||
ironing_spacing = 0.1
|
||||
ironing_speed = 20
|
||||
ironing_type = top
|
||||
layer_height = 0.2
|
||||
max_print_speed = 100
|
||||
max_volumetric_speed = 0
|
||||
min_skirt_length = 10
|
||||
notes =
|
||||
only_retract_when_crossing_perimeters = 1
|
||||
ooze_prevention = 0
|
||||
output_filename_format = [input_filename_base].gcode
|
||||
overhangs = 1
|
||||
perimeter_acceleration = 0
|
||||
perimeter_extruder = 1
|
||||
perimeter_extrusion_width = 0.44
|
||||
perimeter_speed = 60
|
||||
perimeters = 4
|
||||
post_process =
|
||||
print_settings_id = delta
|
||||
raft_layers = 0
|
||||
resolution = 0
|
||||
seam_position = aligned
|
||||
single_extruder_multi_material_priming = 1
|
||||
skirt_distance = 6
|
||||
skirt_height = 1
|
||||
skirts = 1
|
||||
slice_closing_radius = 0.049
|
||||
small_perimeter_speed = 50%
|
||||
solid_infill_below_area = 70
|
||||
solid_infill_every_layers = 0
|
||||
solid_infill_extruder = 1
|
||||
solid_infill_extrusion_width = 0.44
|
||||
solid_infill_speed = 60
|
||||
spiral_vase = 0
|
||||
standby_temperature_delta = -5
|
||||
support_material = 0
|
||||
support_material_angle = 0
|
||||
support_material_auto = 1
|
||||
support_material_buildplate_only = 1
|
||||
support_material_contact_distance = 0.23
|
||||
support_material_enforce_layers = 0
|
||||
support_material_extruder = 1
|
||||
support_material_extrusion_width = 0.45
|
||||
support_material_interface_contact_loops = 0
|
||||
support_material_interface_extruder = 1
|
||||
support_material_interface_layers = 3
|
||||
support_material_interface_spacing = 0
|
||||
support_material_interface_speed = 100%
|
||||
support_material_pattern = rectilinear-grid
|
||||
support_material_spacing = 2.5
|
||||
support_material_speed = 60
|
||||
support_material_synchronize_layers = 0
|
||||
support_material_threshold = 25
|
||||
support_material_with_sheath = 1
|
||||
support_material_xy_spacing = 60%
|
||||
thin_walls = 1
|
||||
threads = 8
|
||||
top_fill_pattern = monotonic
|
||||
top_infill_extrusion_width = 0.44
|
||||
top_solid_infill_speed = 20
|
||||
top_solid_layers = 4
|
||||
top_solid_min_thickness = 0
|
||||
travel_speed = 222
|
||||
wipe_tower = 0
|
||||
wipe_tower_bridging = 10
|
||||
wipe_tower_no_sparse_layers = 0
|
||||
wipe_tower_rotation_angle = 0
|
||||
wipe_tower_width = 60
|
||||
wipe_tower_x = 180
|
||||
wipe_tower_y = 140
|
||||
xy_size_compensation = 0
|
||||
@@ -0,0 +1,114 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-09 at 15:48:42 UTC
|
||||
avoid_crossing_perimeters = 0
|
||||
bottom_fill_pattern = rectilinear
|
||||
bottom_solid_layers = 3
|
||||
bottom_solid_min_thickness = 0
|
||||
bridge_acceleration = 0
|
||||
bridge_angle = 0
|
||||
bridge_flow_ratio = 0.91
|
||||
bridge_speed = 100
|
||||
brim_width = 0
|
||||
clip_multipart_objects = 1
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
complete_objects = 0
|
||||
default_acceleration = 0
|
||||
dont_support_bridges = 1
|
||||
draft_shield = 0
|
||||
elefant_foot_compensation = 0.1
|
||||
ensure_vertical_shell_thickness = 1
|
||||
external_perimeter_extrusion_width = 0.42
|
||||
external_perimeter_speed = 100
|
||||
external_perimeters_first = 0
|
||||
extra_perimeters = 1
|
||||
extruder_clearance_height = 20
|
||||
extruder_clearance_radius = 20
|
||||
extrusion_width = 0.44
|
||||
fill_angle = 45
|
||||
fill_density = 15%
|
||||
fill_pattern = cubic
|
||||
first_layer_acceleration = 0
|
||||
first_layer_extrusion_width = 0.44
|
||||
first_layer_height = 0.3
|
||||
first_layer_speed = 40
|
||||
gap_fill_speed = 100
|
||||
gcode_comments = 0
|
||||
gcode_label_objects = 0
|
||||
infill_acceleration = 0
|
||||
infill_every_layers = 1
|
||||
infill_extruder = 1
|
||||
infill_extrusion_width = 0.44
|
||||
infill_first = 0
|
||||
infill_only_where_needed = 0
|
||||
infill_overlap = 30%
|
||||
infill_speed = 100
|
||||
inherits =
|
||||
interface_shells = 0
|
||||
layer_height = 0.2
|
||||
max_print_speed = 200
|
||||
max_volumetric_speed = 0
|
||||
min_skirt_length = 10
|
||||
notes =
|
||||
only_retract_when_crossing_perimeters = 0
|
||||
ooze_prevention = 0
|
||||
output_filename_format = [input_filename_base].gcode
|
||||
overhangs = 1
|
||||
perimeter_acceleration = 0
|
||||
perimeter_extruder = 1
|
||||
perimeter_extrusion_width = 0.44
|
||||
perimeter_speed = 100
|
||||
perimeters = 3
|
||||
post_process =
|
||||
print_settings_id =
|
||||
raft_layers = 0
|
||||
resolution = 0
|
||||
seam_position = aligned
|
||||
single_extruder_multi_material_priming = 1
|
||||
skirt_distance = 6
|
||||
skirt_height = 1
|
||||
skirts = 1
|
||||
slice_closing_radius = 0.049
|
||||
small_perimeter_speed = 100
|
||||
solid_infill_below_area = 70
|
||||
solid_infill_every_layers = 0
|
||||
solid_infill_extruder = 1
|
||||
solid_infill_extrusion_width = 0.44
|
||||
solid_infill_speed = 100
|
||||
spiral_vase = 0
|
||||
standby_temperature_delta = -5
|
||||
support_material = 0
|
||||
support_material_angle = 0
|
||||
support_material_auto = 1
|
||||
support_material_buildplate_only = 1
|
||||
support_material_contact_distance = 0.2
|
||||
support_material_enforce_layers = 0
|
||||
support_material_extruder = 1
|
||||
support_material_extrusion_width = 0.45
|
||||
support_material_interface_contact_loops = 0
|
||||
support_material_interface_extruder = 1
|
||||
support_material_interface_layers = 3
|
||||
support_material_interface_spacing = 0
|
||||
support_material_interface_speed = 100%
|
||||
support_material_pattern = rectilinear
|
||||
support_material_spacing = 1.5
|
||||
support_material_speed = 100
|
||||
support_material_synchronize_layers = 0
|
||||
support_material_threshold = 20
|
||||
support_material_with_sheath = 1
|
||||
support_material_xy_spacing = 50%
|
||||
thin_walls = 1
|
||||
threads = 8
|
||||
top_fill_pattern = rectilinear
|
||||
top_infill_extrusion_width = 0.44
|
||||
top_solid_infill_speed = 100
|
||||
top_solid_layers = 3
|
||||
top_solid_min_thickness = 0
|
||||
travel_speed = 250
|
||||
wipe_tower = 0
|
||||
wipe_tower_bridging = 10
|
||||
wipe_tower_no_sparse_layers = 0
|
||||
wipe_tower_rotation_angle = 0
|
||||
wipe_tower_width = 60
|
||||
wipe_tower_x = 180
|
||||
wipe_tower_y = 140
|
||||
xy_size_compensation = 0
|
||||
@@ -0,0 +1,75 @@
|
||||
# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-11-07 at 20:30:02 UTC
|
||||
bed_custom_model =
|
||||
bed_custom_texture =
|
||||
bed_shape = 89.6575x7.84402,88.6327x15.6283,86.9333x23.2937,84.5723x30.7818,81.5677x38.0356,77.9423x45,73.7237x51.6219,68.944x57.8509,63.6396x63.6396,57.8509x68.944,51.6219x73.7237,45x77.9423,38.0356x81.5677,30.7818x84.5723,23.2937x86.9333,15.6283x88.6327,7.84402x89.6575,5.51091e-15x90,-7.84402x89.6575,-15.6283x88.6327,-23.2937x86.9333,-30.7818x84.5723,-38.0356x81.5677,-45x77.9423,-51.6219x73.7237,-57.8509x68.944,-63.6396x63.6396,-68.944x57.8509,-73.7237x51.6219,-77.9423x45,-81.5677x38.0356,-84.5723x30.7818,-86.9333x23.2937,-88.6327x15.6283,-89.6575x7.84402,-90x1.10218e-14,-89.6575x-7.84402,-88.6327x-15.6283,-86.9333x-23.2937,-84.5723x-30.7818,-81.5677x-38.0356,-77.9423x-45,-73.7237x-51.6219,-68.944x-57.8509,-63.6396x-63.6396,-57.8509x-68.944,-51.6219x-73.7237,-45x-77.9423,-38.0356x-81.5677,-30.7818x-84.5723,-23.2937x-86.9333,-15.6283x-88.6327,-7.84402x-89.6575,-1.65327e-14x-90,7.84402x-89.6575,15.6283x-88.6327,23.2937x-86.9333,30.7818x-84.5723,38.0356x-81.5677,45x-77.9423,51.6219x-73.7237,57.8509x-68.944,63.6396x-63.6396,68.944x-57.8509,73.7237x-51.6219,77.9423x-45,81.5677x-38.0356,84.5723x-30.7818,86.9333x-23.2937,88.6327x-15.6283,89.6575x-7.84402,90x-2.20436e-14
|
||||
before_layer_gcode = ; Layer change to Layer [layer_num]\n; Z=[layer_z]\n
|
||||
between_objects_gcode =
|
||||
cooling_tube_length = 5
|
||||
cooling_tube_retraction = 91.5
|
||||
default_filament_profile = ""
|
||||
default_print_profile =
|
||||
deretract_speed = 0
|
||||
end_gcode = M104 S0 ; turn off hotend temperature\nM190 S0; turn off bed temperature\nM106; hotend fan full blast\nG28; home \nM84; disable motors\nG4 S10; wait 10 seconds for hotend cooldown\n; play some tunes:\n;Mission Impossible\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2637 P75\nM300 S2793 P75\nM300 S2959 P75\nM300 S3135 P75\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S1864 P150\nM300 S0 P150\nM300 S2093 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S2793 P150\nM300 S0 P150\nM300 S2959 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S1864 P150\nM300 S0 P150\nM300 S2093 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S2793 P150\nM300 S0 P150\nM300 S2959 P150\nM300 S0 P150\nM300 S1864 P150\nM300 S3135 P150\nM300 S2349 P1200\nM300 S0 P75\nM300 S1864 P150\nM300 S3135 P150\nM300 S2217 P1200\nM300 S0 P75\nM300 S1864 P150\nM300 S3135 P150\nM300 S2093 P1200\nM300 S0 P150\nM300 S932 P150\nM300 S2093 P150\n; end of tune\nG4 S120; wait another 2 Minutes for hotend cooldown\nM107; hotend fan off
|
||||
extra_loading_move = -2
|
||||
extruder_colour = #019B9B
|
||||
extruder_offset = 0x0
|
||||
gcode_flavor = marlin
|
||||
high_current_on_filament_swap = 0
|
||||
host_type = octoprint
|
||||
inherits =
|
||||
layer_gcode =
|
||||
machine_max_acceleration_e = 10000,5000
|
||||
machine_max_acceleration_extruding = 1500,1250
|
||||
machine_max_acceleration_retracting = 1500,1250
|
||||
machine_max_acceleration_x = 9000,9000
|
||||
machine_max_acceleration_y = 9000,9000
|
||||
machine_max_acceleration_z = 9000,9000
|
||||
machine_max_feedrate_e = 250,250
|
||||
machine_max_feedrate_x = 1500,1500
|
||||
machine_max_feedrate_y = 1500,1500
|
||||
machine_max_feedrate_z = 1500,1500
|
||||
machine_max_jerk_e = 2.5,2.5
|
||||
machine_max_jerk_x = 9,9
|
||||
machine_max_jerk_y = 9,9
|
||||
machine_max_jerk_z = 9,9
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
max_layer_height = 0
|
||||
max_print_height = 196
|
||||
min_layer_height = 0.1
|
||||
nozzle_diameter = 0.4
|
||||
parking_pos_retraction = 92
|
||||
print_host =
|
||||
printer_model =
|
||||
printer_notes =
|
||||
printer_settings_id =
|
||||
printer_technology = FFF
|
||||
printer_variant =
|
||||
printer_vendor =
|
||||
printhost_apikey =
|
||||
printhost_cafile =
|
||||
remaining_times = 1
|
||||
retract_before_travel = 2
|
||||
retract_before_wipe = 10%
|
||||
retract_layer_change = 0
|
||||
retract_length = 2
|
||||
retract_length_toolchange = 10
|
||||
retract_lift = 0.2
|
||||
retract_lift_above = 0.3
|
||||
retract_lift_below = 150
|
||||
retract_restart_extra = 0
|
||||
retract_restart_extra_toolchange = 0
|
||||
retract_speed = 30
|
||||
serial_port =
|
||||
serial_speed = 250000
|
||||
silent_mode = 1
|
||||
single_extruder_multi_material = 0
|
||||
start_gcode = G28 ; home all axes\nM140 S[first_layer_bed_temperature] ; set bed final temp\nG1 X0 Y0 Z100 F4000 ; safe position\nG1 X0 Y-50 Z5 F4000 ; lift nozzle\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\nM104 S[first_layer_temperature] ; set extruder final temp\nM109 S[first_layer_temperature] ; wait for extruder final temp\nG1 X0 Y-45 Z0.3 F3000 ; move down\n;G1 Z0.5; lift\nG92 E0\n{if perimeter_speed >= 100}M900 K0; Disable LINEAR_ADVANCE for speed's sake!\n{elsif perimeter_speed >= 65}M900 K0.2; reduced LINEAR_ADVANCE because of higher speeds\n{else}M900 K0.38; LINEAR_ADVANCE high quality preset\n{endif}
|
||||
thumbnails =
|
||||
toolchange_gcode =
|
||||
use_firmware_retraction = 0
|
||||
use_relative_e_distances = 0
|
||||
use_volumetric_e = 0
|
||||
variable_layer_height = 1
|
||||
wipe = 0
|
||||
z_offset = 0
|
||||
@@ -0,0 +1,22 @@
|
||||
# generated by PrusaSlicer 2.3.0+linux-x64 on 2021-02-21 at 11:46:13 UTC
|
||||
|
||||
[snapshot]
|
||||
id = 20210221T114613Z
|
||||
time_captured = 20210221T114613Z
|
||||
slic3r_version_captured = 2.3.0+linux-x64
|
||||
comment =
|
||||
reason = upgrade
|
||||
|
||||
[presets]
|
||||
print = delta
|
||||
sla_print =
|
||||
filament = PETG-DasFilament_Saphirblau
|
||||
sla_material =
|
||||
printer = delta
|
||||
physical_printer =
|
||||
|
||||
[Vendor:PrusaResearch]
|
||||
version = 1.1.11
|
||||
min_slic3r_version = 2.2.0-alpha3
|
||||
max_slic3r_version = 2147483647.2147483647.2147483647
|
||||
model_MINI = 0.25;0.4;0.6
|
||||
+5519
File diff suppressed because it is too large
Load Diff
Reference in New Issue
Block a user