prusaslicer profiles

PrusaSlicer/snapshots/20211112T225913Z/filament/PETG-DasFilament_Saphirblau.ini

@@ -0,0 +1,57 @@
+# generated by PrusaSlicer 2.3.0+linux-x64 on 2021-05-27 at 05:24:47 UTC
+bed_temperature = 75
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = 
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 2
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 0.99
+fan_always_on = 1
+fan_below_layer_time = 30
+filament_colour = #1730DD
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 25
+filament_density = 1.18
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = "Noulei Silk PLA Filaments.\nPrint well on low temps <200°C, but black has far better strength and layer adhesion than the bright colours.\nSuccessfully tested filaments already testet on delta /w e3dv6/0.4:\n#24 Silk Black\n#11Silk Blue\n#14Silk Silver Blue\n\nDasFilament PETG:\nusually good at 230/70°C, but spahipblau prints better at 220.\n\nnext ones to test out:\n#26 antique gold\n#9 red\n#4 white\npetg?"
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = PETG-DasFilament_Saphirblau
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_type = PET
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 70
+first_layer_temperature = 235
+full_fan_speed_layer = 3
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 15
+slowdown_below_layer_time = 10
+start_filament_gcode = "; Filament gcode\n"
+temperature = 240

PrusaSlicer/snapshots/20211112T225913Z/filament/PETG-Tinmorry White.ini

@@ -0,0 +1,55 @@
+# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-11-09 at 06:05:44 UTC
+bed_temperature = 70
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = 
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 0.97
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #000000
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 20
+filament_density = 1.18
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = "Noulei Silk PLA Filaments.\nPrint well on low temps <200°C, but black has far better strength and layer adhesion than the bright colours.\nSuccessfully tested filaments already testet on delta /w e3dv6/0.4:\n\n#24 Silk Black\n#11Silk Blue\n#14Silk Silver Blue\n\nnext ones to test out:\n#26 antique gold\n#9 red\n#4 white\npetg?"
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_toolchange_delay = 0
+filament_type = PET
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 72
+first_layer_temperature = 235
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+slowdown_below_layer_time = 8
+start_filament_gcode = "; Filament gcode\n"
+temperature = 230

PrusaSlicer/snapshots/20211112T225913Z/filament/PLA_Geetech_Black.ini

@@ -0,0 +1,57 @@
+# generated by PrusaSlicer 2.3.0+linux-x64 on 2021-06-23 at 14:26:28 UTC
+bed_temperature = 65
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = 
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 0.95
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #0EFB7C
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 20
+filament_density = 1.18
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 65
+first_layer_temperature = 200
+full_fan_speed_layer = 0
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+slowdown_below_layer_time = 8
+start_filament_gcode = "; Filament gcode\n"
+temperature = 195

PrusaSlicer/snapshots/20211112T225913Z/filament/PLA_Noulei-Silk Filaments.ini

@@ -0,0 +1,55 @@
+# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-15 at 21:23:23 UTC
+bed_temperature = 55
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = 
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 0.95
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #000000
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 20
+filament_density = 1.18
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = "Noulei Silk PLA Filaments.\nPrint well on low temps <200°C, but black has far better strength and layer adhesion than the bright colours.\nSuccessfully tested filaments already testet on delta /w e3dv6/0.4:\n\n#24 Silk Black\n#11Silk Blue\n#14Silk Silver Blue\n\nnext ones to test out:\n#26 antique gold\n#9 red\n#4 white\npetg?"
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_toolchange_delay = 0
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 55
+first_layer_temperature = 192
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 40
+min_print_speed = 10
+slowdown_below_layer_time = 8
+start_filament_gcode = "; Filament gcode\n"
+temperature = 190

PrusaSlicer/snapshots/20211112T225913Z/filament/sparky.ini

@@ -0,0 +1,57 @@
+# generated by PrusaSlicer 2.3.0+linux-x64 on 2021-06-20 at 21:08:45 UTC
+bed_temperature = 60
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = 
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 3
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #29B2B2
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 0
+filament_density = 0
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 65
+first_layer_temperature = 200
+full_fan_speed_layer = 0
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+slowdown_below_layer_time = 5
+start_filament_gcode = "; Filament gcode\n"
+temperature = 200

PrusaSlicer/snapshots/20211112T225913Z/print/delta.ini

@@ -0,0 +1,122 @@
+# generated by PrusaSlicer 2.3.0+linux-x64 on 2021-06-14 at 08:38:14 UTC
+avoid_crossing_perimeters = 0
+avoid_crossing_perimeters_max_detour = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 4
+bottom_solid_min_thickness = 1
+bridge_acceleration = 0
+bridge_angle = 0
+bridge_flow_ratio = 0.92
+bridge_speed = 50
+brim_width = 0
+clip_multipart_objects = 1
+compatible_printers = 
+compatible_printers_condition = 
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+draft_shield = 0
+elefant_foot_compensation = 0.1
+ensure_vertical_shell_thickness = 1
+external_perimeter_extrusion_width = 0.4
+external_perimeter_speed = 40
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0.4
+fill_angle = 45
+fill_density = 30%
+fill_pattern = cubic
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0.45
+first_layer_height = 0.25
+first_layer_speed = 30
+gap_fill_speed = 30
+gcode_comments = 0
+gcode_label_objects = 0
+infill_acceleration = 0
+infill_anchor = 600%
+infill_anchor_max = 50
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0.45
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 25%
+infill_speed = 100
+inherits = 
+interface_shells = 0
+ironing = 0
+ironing_flowrate = 13%
+ironing_spacing = 0.1
+ironing_speed = 20
+ironing_type = top
+layer_height = 0.25
+max_print_speed = 100
+max_volumetric_speed = 0
+min_skirt_length = 10
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0.4
+perimeter_speed = 60
+perimeters = 4
+post_process = 
+print_settings_id = delta
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+single_extruder_multi_material_priming = 1
+skirt_distance = 4
+skirt_height = 1
+skirts = 1
+slice_closing_radius = 0.049
+small_perimeter_speed = 50%
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0.45
+solid_infill_speed = 100
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 1
+support_material_buildplate_only = 0
+support_material_contact_distance = 0.25
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0.35
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear-grid
+support_material_spacing = 2
+support_material_speed = 80
+support_material_synchronize_layers = 0
+support_material_threshold = 30
+support_material_with_sheath = 0
+support_material_xy_spacing = 60%
+thin_walls = 1
+threads = 8
+top_fill_pattern = monotonic
+top_infill_extrusion_width = 0.4
+top_solid_infill_speed = 40
+top_solid_layers = 4
+top_solid_min_thickness = 1
+travel_speed = 200
+wipe_tower = 0
+wipe_tower_bridging = 10
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 180
+wipe_tower_y = 140
+xy_size_compensation = 0

PrusaSlicer/snapshots/20211112T225913Z/print/delta_speed-draft_100mm.ini

@@ -0,0 +1,114 @@
+# generated by PrusaSlicer 2.2.0+linux-x64 on 2020-10-09 at 15:48:42 UTC
+avoid_crossing_perimeters = 0
+bottom_fill_pattern = rectilinear
+bottom_solid_layers = 3
+bottom_solid_min_thickness = 0
+bridge_acceleration = 0
+bridge_angle = 0
+bridge_flow_ratio = 0.91
+bridge_speed = 100
+brim_width = 0
+clip_multipart_objects = 1
+compatible_printers = 
+compatible_printers_condition = 
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+draft_shield = 0
+elefant_foot_compensation = 0.1
+ensure_vertical_shell_thickness = 1
+external_perimeter_extrusion_width = 0.42
+external_perimeter_speed = 100
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0.44
+fill_angle = 45
+fill_density = 15%
+fill_pattern = cubic
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0.44
+first_layer_height = 0.3
+first_layer_speed = 40
+gap_fill_speed = 100
+gcode_comments = 0
+gcode_label_objects = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0.44
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 30%
+infill_speed = 100
+inherits = 
+interface_shells = 0
+layer_height = 0.2
+max_print_speed = 200
+max_volumetric_speed = 0
+min_skirt_length = 10
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0.44
+perimeter_speed = 100
+perimeters = 3
+post_process = 
+print_settings_id = 
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+single_extruder_multi_material_priming = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 1
+slice_closing_radius = 0.049
+small_perimeter_speed = 100
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0.44
+solid_infill_speed = 100
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 1
+support_material_buildplate_only = 1
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0.45
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 1.5
+support_material_speed = 100
+support_material_synchronize_layers = 0
+support_material_threshold = 20
+support_material_with_sheath = 1
+support_material_xy_spacing = 50%
+thin_walls = 1
+threads = 8
+top_fill_pattern = rectilinear
+top_infill_extrusion_width = 0.44
+top_solid_infill_speed = 100
+top_solid_layers = 3
+top_solid_min_thickness = 0
+travel_speed = 250
+wipe_tower = 0
+wipe_tower_bridging = 10
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 180
+wipe_tower_y = 140
+xy_size_compensation = 0

PrusaSlicer/snapshots/20211112T225913Z/print/sparky.ini

@@ -0,0 +1,122 @@
+# generated by PrusaSlicer 2.3.0+linux-x64 on 2021-06-23 at 10:26:16 UTC
+avoid_crossing_perimeters = 0
+avoid_crossing_perimeters_max_detour = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 3
+bottom_solid_min_thickness = 0
+bridge_acceleration = 0
+bridge_angle = 0
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+clip_multipart_objects = 1
+compatible_printers = 
+compatible_printers_condition = 
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+draft_shield = 0
+elefant_foot_compensation = 0.2
+ensure_vertical_shell_thickness = 1
+external_perimeter_extrusion_width = 0.45
+external_perimeter_speed = 30
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0.45
+fill_angle = 45
+fill_density = 20%
+fill_pattern = stars
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0.42
+first_layer_height = 0.3
+first_layer_speed = 30
+gap_fill_speed = 20
+gcode_comments = 0
+gcode_label_objects = 0
+infill_acceleration = 0
+infill_anchor = 600%
+infill_anchor_max = 50
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0.45
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 25%
+infill_speed = 80
+inherits = 
+interface_shells = 0
+ironing = 0
+ironing_flowrate = 15%
+ironing_spacing = 0.1
+ironing_speed = 15
+ironing_type = top
+layer_height = 0.3
+max_print_speed = 80
+max_volumetric_speed = 0
+min_skirt_length = 10
+notes = 
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0.45
+perimeter_speed = 60
+perimeters = 3
+post_process = 
+print_settings_id = 
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+single_extruder_multi_material_priming = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 1
+slice_closing_radius = 0.049
+small_perimeter_speed = 30
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0.45
+solid_infill_speed = 60
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 1
+support_material_buildplate_only = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0.35
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2.5
+support_material_speed = 60
+support_material_synchronize_layers = 0
+support_material_threshold = 0
+support_material_with_sheath = 1
+support_material_xy_spacing = 50%
+thin_walls = 1
+threads = 8
+top_fill_pattern = monotonic
+top_infill_extrusion_width = 0.4
+top_solid_infill_speed = 20
+top_solid_layers = 3
+top_solid_min_thickness = 0
+travel_speed = 130
+wipe_tower = 0
+wipe_tower_bridging = 10
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 180
+wipe_tower_y = 140
+xy_size_compensation = 0

PrusaSlicer/snapshots/20211112T225913Z/printer/delta.ini

@@ -0,0 +1,77 @@
+# generated by PrusaSlicer 2.3.0+linux-x64 on 2021-05-31 at 16:56:56 UTC
+bed_custom_model = 
+bed_custom_texture = 
+bed_shape = 89.6575x7.84402,88.6327x15.6283,86.9333x23.2937,84.5723x30.7818,81.5677x38.0356,77.9423x45,73.7237x51.6219,68.944x57.8509,63.6396x63.6396,57.8509x68.944,51.6219x73.7237,45x77.9423,38.0356x81.5677,30.7818x84.5723,23.2937x86.9333,15.6283x88.6327,7.84402x89.6575,5.51091e-15x90,-7.84402x89.6575,-15.6283x88.6327,-23.2937x86.9333,-30.7818x84.5723,-38.0356x81.5677,-45x77.9423,-51.6219x73.7237,-57.8509x68.944,-63.6396x63.6396,-68.944x57.8509,-73.7237x51.6219,-77.9423x45,-81.5677x38.0356,-84.5723x30.7818,-86.9333x23.2937,-88.6327x15.6283,-89.6575x7.84402,-90x1.10218e-14,-89.6575x-7.84402,-88.6327x-15.6283,-86.9333x-23.2937,-84.5723x-30.7818,-81.5677x-38.0356,-77.9423x-45,-73.7237x-51.6219,-68.944x-57.8509,-63.6396x-63.6396,-57.8509x-68.944,-51.6219x-73.7237,-45x-77.9423,-38.0356x-81.5677,-30.7818x-84.5723,-23.2937x-86.9333,-15.6283x-88.6327,-7.84402x-89.6575,-1.65327e-14x-90,7.84402x-89.6575,15.6283x-88.6327,23.2937x-86.9333,30.7818x-84.5723,38.0356x-81.5677,45x-77.9423,51.6219x-73.7237,57.8509x-68.944,63.6396x-63.6396,68.944x-57.8509,73.7237x-51.6219,77.9423x-45,81.5677x-38.0356,84.5723x-30.7818,86.9333x-23.2937,88.6327x-15.6283,89.6575x-7.84402,90x-2.20436e-14
+before_layer_gcode = ; Layer change to Layer [layer_num]\n; Z=[layer_z]\n
+between_objects_gcode = 
+color_change_gcode = M600
+cooling_tube_length = 5
+cooling_tube_retraction = 91.5
+default_filament_profile = ""
+default_print_profile = 
+deretract_speed = 0
+end_gcode = M104 S0 ; turn off hotend temperature\nM190 S0; turn off bed temperature\nM106; hotend fan full blast\nG28; home \nM84; disable motors\nG4 S10; wait 10 seconds for hotend cooldown\n; play some tunes:\n;Mission Impossible\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2349 P75\nM300 S2349 P75\nM300 S2489 P75\nM300 S2637 P75\nM300 S2793 P75\nM300 S2959 P75\nM300 S3135 P75\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S1864 P150\nM300 S0 P150\nM300 S2093 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S2793 P150\nM300 S0 P150\nM300 S2959 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S1864 P150\nM300 S0 P150\nM300 S2093 P150\nM300 S0 P150\nM300 S3135 P150\nM300 S0 P300\nM300 S3135 P150\nM300 S0 P300\nM300 S2793 P150\nM300 S0 P150\nM300 S2959 P150\nM300 S0 P150\nM300 S1864 P150\nM300 S3135 P150\nM300 S2349 P1200\nM300 S0 P75\nM300 S1864 P150\nM300 S3135 P150\nM300 S2217 P1200\nM300 S0 P75\nM300 S1864 P150\nM300 S3135 P150\nM300 S2093 P1200\nM300 S0 P150\nM300 S932 P150\nM300 S2093 P150\n; end of tune\nG4 S60; wait another 2 Minutes for hotend cooldown\nM107; hotend fan off
+extra_loading_move = -2
+extruder_colour = #019B9B
+extruder_offset = 0x0
+gcode_flavor = marlin
+high_current_on_filament_swap = 0
+host_type = octoprint
+inherits = 
+layer_gcode = 
+machine_limits_usage = emit_to_gcode
+machine_max_acceleration_e = 10000,5000
+machine_max_acceleration_extruding = 1500,1250
+machine_max_acceleration_retracting = 1500,1250
+machine_max_acceleration_x = 9000,9000
+machine_max_acceleration_y = 9000,9000
+machine_max_acceleration_z = 9000,9000
+machine_max_feedrate_e = 250,250
+machine_max_feedrate_x = 1500,1500
+machine_max_feedrate_y = 1500,1500
+machine_max_feedrate_z = 1500,1500
+machine_max_jerk_e = 2.5,2.5
+machine_max_jerk_x = 9,9
+machine_max_jerk_y = 9,9
+machine_max_jerk_z = 9,9
+machine_min_extruding_rate = 0,0
+machine_min_travel_rate = 0,0
+max_layer_height = 0
+max_print_height = 196
+min_layer_height = 0.1
+nozzle_diameter = 0.4
+parking_pos_retraction = 92
+pause_print_gcode = M601
+print_host = 
+printer_model = 
+printer_notes = 
+printer_settings_id = 
+printer_technology = FFF
+printer_variant = 
+printer_vendor = 
+printhost_apikey = 
+printhost_cafile = 
+remaining_times = 1
+retract_before_travel = 2
+retract_before_wipe = 10%
+retract_layer_change = 0
+retract_length = 2
+retract_length_toolchange = 10
+retract_lift = 0.15
+retract_lift_above = 0
+retract_lift_below = 150
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 35
+silent_mode = 1
+single_extruder_multi_material = 0
+start_gcode = G28 ; home all axes\nM140 S[first_layer_bed_temperature] ; set bed final temp\nG1 X0 Y0 Z100 F4000 ; safe position\nG1 X0 Y-50 Z5 F4000 ; lift nozzle\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\nM104 S[first_layer_temperature] ; set extruder final temp\nM109 S[first_layer_temperature] ; wait for extruder final temp\nG1 X0 Y-45 Z0.3 F3000 ; move down\n;G1 Z0.5; lift\nG92 E0\n{if perimeter_speed >= 75}M900 K0; Disable LINEAR_ADVANCE for speed's sake!\n;{elsif perimeter_speed >= 65}M900 K0.2; reduced LINEAR_ADVANCE because of higher speeds\n{else}M900 K0.38; LINEAR_ADVANCE high quality preset\n{endif}
+template_custom_gcode = 
+thumbnails = 
+toolchange_gcode = 
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+use_volumetric_e = 0
+variable_layer_height = 1
+wipe = 0
+z_offset = 0

PrusaSlicer/snapshots/20211112T225913Z/printer/sparky.ini

@@ -0,0 +1,77 @@
+# generated by PrusaSlicer 2.3.0+linux-x64 on 2021-06-22 at 23:05:45 UTC
+bed_custom_model = 
+bed_custom_texture = 
+bed_shape = 0x0,177x0,177x175,0x175
+before_layer_gcode = 
+between_objects_gcode = 
+color_change_gcode = M600
+cooling_tube_length = 5
+cooling_tube_retraction = 91.5
+default_filament_profile = 
+default_print_profile = 
+deretract_speed = 0
+end_gcode = M104 S0 ; turn off hotend\nM140 S0 ; turn off bed\nG28 X0  ; home X axis\nM84     ; disable motors\nM106 S255 ; Cooldown Hotend\nG4 S30 ; wait 30secs\nM107 ; turn off Fan \n
+extra_loading_move = -2
+extruder_colour = ""
+extruder_offset = 0x0
+gcode_flavor = marlin
+high_current_on_filament_swap = 0
+host_type = octoprint
+inherits = 
+layer_gcode = 
+machine_limits_usage = emit_to_gcode
+machine_max_acceleration_e = 10000,5000
+machine_max_acceleration_extruding = 1500,1250
+machine_max_acceleration_retracting = 1500,1250
+machine_max_acceleration_x = 9000,1000
+machine_max_acceleration_y = 9000,1000
+machine_max_acceleration_z = 500,200
+machine_max_feedrate_e = 120,120
+machine_max_feedrate_x = 500,200
+machine_max_feedrate_y = 500,200
+machine_max_feedrate_z = 5,5
+machine_max_jerk_e = 2.5,2.5
+machine_max_jerk_x = 10,10
+machine_max_jerk_y = 10,10
+machine_max_jerk_z = 0.2,0.4
+machine_min_extruding_rate = 0,0
+machine_min_travel_rate = 0,0
+max_layer_height = 0
+max_print_height = 145
+min_layer_height = 0.07
+nozzle_diameter = 0.4
+parking_pos_retraction = 92
+pause_print_gcode = M601
+print_host = 
+printer_model = 
+printer_notes = 
+printer_settings_id = 
+printer_technology = FFF
+printer_variant = 
+printer_vendor = 
+printhost_apikey = 
+printhost_cafile = 
+remaining_times = 0
+retract_before_travel = 2
+retract_before_wipe = 0%
+retract_layer_change = 0
+retract_length = 2
+retract_length_toolchange = 10
+retract_lift = 0.1
+retract_lift_above = 0
+retract_lift_below = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 40
+silent_mode = 1
+single_extruder_multi_material = 0
+start_gcode = G28 ; home all axes\nG1 X0 Y0 Z3 F2500 ; lift nozzle\nG92 E0 ;Reset Extruder\nM140 S[first_layer_bed_temperature]\nM109 S[first_layer_temperature] ; wait for nozzle\nG1 X1 Y0 Z[first_layer_height] F5000.0\nG1 X150 Y0 F1500.0 E12 ; Draw line\nG1 X150 Y5 F5000 ; wipe\nG1 Z1 F2500; lift\nG92 E0; reset Extruder
+template_custom_gcode = 
+thumbnails = 
+toolchange_gcode = 
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+use_volumetric_e = 0
+variable_layer_height = 1
+wipe = 0
+z_offset = 0

PrusaSlicer/snapshots/20211112T225913Z/snapshot.ini

@@ -0,0 +1,23 @@
+# generated by PrusaSlicer 2.3.3+linux-x64 on 2021-11-12 at 22:59:14 UTC
+
+[snapshot]
+id = 20211112T225913Z
+time_captured = 20211112T225913Z
+slic3r_version_captured = 2.3.3+linux-x64
+comment = 
+reason = upgrade
+
+[presets]
+print = delta
+sla_print = 
+filament = PETG-DasFilament_Saphirblau
+sla_material = 
+printer = delta
+physical_printer = 
+
+[Vendor:PrusaResearch]
+version = 1.2.4
+min_slic3r_version = 2.3.0-rc1
+max_slic3r_version = 2147483647.2147483647.2147483647
+model_MINI = 0.25;0.4;0.6
+model_MK3S = 0.4